Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0109809 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) One of the following conditions (A) through (C) is met (2-trip detection logic)
(A) Either of the following conditions 1, 2 or 3 is met:
1. Any 2 or more signals of the following are ON simultaneously:
·

P input signal is ON.

·

R input signal is ON.

·

D input signal is ON.


2. Any 2 or more signals of the following are ON simultaneously:
·

N input signal is ON.

·

R input signal is ON.

·

D input signal is ON.


3. Any 2 or more signals of the following are ON simultaneously:
·

NSW input signal is ON.

·

R input signal is ON.

·

D input signal is ON.


(B) All switches are OFF simultaneously for P, N, NSW, R and D.
(C) When any of following conditions is met for 2.0 sec. or more in the S position:
·

P input signal is ON.

·

N input signal is ON.

·

NSW input signal is ON.

·

R input signal is ON.


·

Open or short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, R or D). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

C245326E03
6.094,5 6.448,5.167 0.354,0.167 10 false ECM 5.708,0.823 6.042,0.99 0.333,0.167 10 false 67 5.708,1.333 6.063,1.5 0.354,0.167 10 false 71 5.719,1.833 6.083,2 0.365,0.167 10 false 66 5.75,2.292 6.073,2.458 0.323,0.167 10 false 70 5.688,3.042 6.031,3.208 0.344,0.167 10 false C1 5.729,2.844 6.073,3.01 0.344,0.167 10 false 63 5.656,4.563 6.01,4.729 0.354,0.167 10 false A43 6,1 6.24,1.167 0.24,0.167 10 false D 6,1.521 6.24,1.688 0.24,0.167 10 false N 6,2.021 6.24,2.188 0.24,0.167 10 false R 6,2.521 6.24,2.688 0.24,0.167 10 false P 6,3.042 6.604,3.208 0.604,0.167 10 false NSW 5.969,4.563 6.208,4.729 0.24,0.167 10 false S 5.708,4.385 5.948,4.552 0.24,0.167 10 false 27 3.052,0.896 3.292,1.063 0.24,0.167 10 false 7 3.052,1.396 3.292,1.563 0.24,0.167 10 false 8 3.052,1.906 3.292,2.073 0.24,0.167 10 false 2 3.052,2.417 3.292,2.583 0.24,0.167 10 false 3 3.052,2.938 3.292,3.104 0.24,0.167 10 false 4 1.875,2.927 2.115,3.094 0.24,0.167 10 false 9 1.875,1.698 2.115,1.865 0.24,0.167 10 false 1 1.865,4.458 2.104,4.625 0.24,0.167 10 false 3 2.781,0.906 3.021,1.073 0.24,0.167 10 false DL 2.781,1.396 3.021,1.563 0.24,0.167 10 false NL 2.781,1.906 3.021,2.073 0.24,0.167 10 false RL 2.052,1.708 2.292,1.875 0.24,0.167 10 false RB 2.781,2.417 3.021,2.583 0.24,0.167 10 false PL 2.833,2.938 3,3.104 0.167,0.167 10 false B 2.844,4.458 3.083,4.625 0.24,0.167 10 false S 2.063,4.458 2.302,4.625 0.24,0.167 10 false IG 0.25,1.729 0.781,2.521 0.531,0.792 10 false from BKUP LP Fuse 0.125,4.573 0.708,5.271 0.583,0.698 10 false from IG1 NO. 3 Fuse 0.323,3.042 0.75,3.583 0.427,0.542 10 false to ST Relay 1.635,3.5 2.01,3.688 0.375,0.188 10 false C14 1.604,5.01 4.073,5.198 2.469,0.188 10 false Transmission Control Switch 2.073,2.938 2.24,3.104 0.167,0.167 10 false L 3.052,4.458 3.271,4.625 0.219,0.167 10 false 7 1.635,3.667 3.406,4.063 1.771,0.396 10 false Park/Neutral Position Switch Assembly 1.604,4.865 1.969,5.042 0.365,0.177 10 false F46 5.688,2.531 6.031,2.698 0.344,0.167 10 false C1 5.688,2.021 6.031,2.188 0.344,0.167 10 false C1 5.688,1.51 6.031,1.677 0.344,0.167 10 false C1 5.688,1 6.031,1.167 0.344,0.167 10 false C1

CAUTION / NOTICE / HINT

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (P Range) PNP switch status ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Sports Mode Selection SW Sport mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) PNP switch status ON or OFF
·

ON: Shift lever in D or S

·

OFF: Shift lever not in D or S


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Powertrain > Engine > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Sports Mode Selection SW
Shift SW Status (D Range)
50003 234 147,125,126,127,133,128


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
C190067C06
0.469,1.573 0.813,1.833 0.344,0.26 1.656,1.594 2.094,1.063 false 2.125,0.906 2.427,1.094 0.302,0.188 10 false RB 0.531,1.635 0.833,1.781 0.302,0.146 10 false C14 0.823,0.677 1.031,0.865 0.208,0.188 10 false *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C14-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)
a.
C190067C07
0.49,1.573 0.823,1.833 0.333,0.26 2.198,1.646 2.865,1.271 false 2.906,1.135 3.302,1.281 0.396,0.146 10 false B 0.542,1.635 0.885,1.781 0.344,0.146 10 false C14 0.698,0.75 0.885,0.958 0.188,0.208 10 false *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C14-4 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C275091C02
0.219,2.271 0.51,2.521 0.292,0.25 1.167,1.708 0.74,1.177 false 1.344,1.708 1.125,1.188 false 1.604,1.688 1.75,1.167 false 1.896,1.698 2.177,1.177 false 1.75,2.135 2.052,2.625 false 1.417,2.135 1.5,2.646 false 1.24,2.146 1.052,2.604 false 0.354,0.771 0.667,0.969 0.313,0.198 10 false *a 0.25,2.313 0.563,2.51 0.313,0.198 10 false C14 1.01,2.667 1.167,2.865 0.156,0.198 10 false L 1.438,2.667 1.75,2.865 0.313,0.198 10 false NL 2,2.667 2.313,2.865 0.313,0.198 10 false DL 0.667,0.969 0.823,1.167 0.156,0.198 10 false B 1.021,0.969 1.333,1.167 0.313,0.198 10 false PL 1.667,0.969 1.979,1.167 0.313,0.198 10 false RL 2.104,0.969 2.417,1.167 0.313,0.198 10 false RB
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
C14-4 (B) - C14-9 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher
C14-1 (RB) - C14-3 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
C14-1 (RB) - C14-8 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
C14-1 (RB) - C14-2 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
C14-1 (RB) - C14-7 (DL) Shift lever in D, S, "+" or "-" Below 1 Ω
Shift lever not in D, S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

4.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C168599C02
1.646,1.854 1.438,1.323 true 1.25,2.521 1.667,2.104 true 0.208,0.198 0.583,0.49 0.375,0.292 10 false *a 1.25,1.135 1.563,1.333 0.313,0.198 10 false IG 1.021,2.5 1.333,2.698 0.313,0.198 10 false S
*a Component without harness connected
(Transmission Control Switch)


Connect the park/neutral position switch assembly connector.


b.

Disconnect the transmission control switch connector from transmission floor shift assembly.


c.

Measure resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
F46-3 (IG) - F46-7 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)

NG

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)
a.
C245085C02
0.531,0.948 0.99,1.167 0.458,0.219 1.917,2.531 2.229,1.875 false 0.646,0.979 1.031,1.156 0.385,0.177 10 false A43 0.406,0.427 0.688,0.625 0.281,0.198 10 false *a 1.833,2.542 2.156,2.75 0.323,0.208 10 false S
*a Front view of wire harness connector
(to ECM)


Connect the transmission control switch connector.


b.

Disconnect the ECM connector.


c.

Turn the ignition switch to ON, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-27 (S) - Body ground Shift lever in S, "+" or "-" 11 to 14 V
Shift lever not in S, "+" or "-" Below 1 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.
C245086C02
0.365,0.802 0.76,1.031 0.396,0.229 0.698,1.802 0.49,2.49 false 0.771,1.802 0.979,2.333 false 1.073,1.813 1.396,2.563 false 1.146,1.813 1.677,2.344 false 0.156,0.375 0.448,0.573 0.292,0.198 10 false *a 1.385,2.594 1.781,2.802 0.396,0.208 10 false P 1.698,2.333 2,2.542 0.302,0.208 10 false N 0.927,2.365 1.229,2.573 0.302,0.208 10 false D 0.427,2.51 0.729,2.719 0.302,0.208 10 false R 0.479,0.833 0.875,1.01 0.396,0.177 10 false C1
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard Voltage:
Tester Connection Condition Specified Condition
C1-70 (P) - Body ground Shift lever in P 11 to 14 V
Shift lever not in P Below 1 V
C1-71 (N) - Body ground Shift lever in N 11 to 14 V
Shift lever not in N Below 1 V
C1-66 (R) - Body ground Shift lever in R 11 to 14 V*
Shift lever not in R Below 1 V
C1-67 (D) - Body ground Shift lever in D, S, "+" or "-" 11 to 14 V
Shift lever not in D, S, "+" or "-" Below 1 V


HINT:

*: The voltage will drop slightly due to lighting up of the back up light.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Disconnect the park/neutral position switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C14-4 (B) - C1-63 (NSW) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C14-4 (B) or C1-63 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR