The rear mode damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear mode damper servo sub-assembly to the appropriate position, which controls the air outlet switching.
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the No. 2 air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1486/86 | Driver Side Air Outlet Damper Control Servo Motor Circuit | Rear air outlet damper position sensor value does not change even if air conditioning amplifier assembly operates rear mode damper servo sub-assembly | ·
Rear mode damper servo sub-assembly ·
No. 2 air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized
(30 sec. or more)*1 |
*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
Confirm that no mechanical problems are present because this DTC can be output when either a damper link or damper is mechanically locked.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Operate the rear passenger side mode switch.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Air Outlet Servo Pls (F&R D) | Rear mode damper servo sub-assembly target pulse | Min.: 128
Max.: 383 |
·
FACE: 83 (pulse) ·
B/L: 38 (pulse) ·
FOOT: 7 (pulse) |
- |
| A/O Servo Actual Pulse(F&R D) | Rear mode damper servo sub-assembly actual pulse | Min.: 128
Max.: 383 |
·
FACE: 83 (pulse) ·
B/L: 38 (pulse) ·
FOOT: 7 (pulse) |
- |
| Tester Display |
|---|
| Air Outlet Servo Pls (F&R D) |
| A/O Servo Actual Pulse(F&R D) |
When the rear passenger side mode switch is operated, the actual pulse changes following the target pulse.
| Result | Proceed to |
|---|---|
| Target pulse changes but actual pulse does not change | A |
| Target pulse and actual pulse do not change | B |
| Actual pulse changes following the target pulse (When troubleshooting according to the DTC) | C |
| Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) | D |
A
B
C
D
Disconnect the L20 No. 2 air conditioning harness assembly connector.
Disconnect the F81 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-27 (R BBU) - L20-4 (R BBU) | Always | Below 1 Ω |
| F81-1 (R BUS) - L20-3 (R BUS) | Always | Below 1 Ω |
| F81-25 (R BUG) - L20-2 (R BUG) | Always | Below 1 Ω |
| F81-27 (R BBU) - Body ground | Always | 10 kΩ or higher |
| F81-1 (R BUS) - Body ground | Always | 10 kΩ or higher |
| F81-25 (R BUG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear mode damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1486/86 is output | A |
| DTC B1486/86 is not output | B |
A
B
Replace the No. 2 air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY
Since the No. 2 air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the No. 2 air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1486/86 is output | A |
| DTC B1486/86 is not output | B |
A
B
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1486/86 is output | A |
| DTC B1486/86 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING