Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM3160E _58 Vehicle Interior _019714 HEATING / AIR CONDITIONING _0109951 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Blower Motor Circuit  


DESCRIPTION

The blower motor with fan sub-assembly is operated by signals from the air conditioning amplifier assembly. Blower motor speed signals are transmitted in accordance with changes in the duty ratio.

WIRING DIAGRAM

E287490E01
0.26,1 1.156,1.26 0.896,0.26 10 false from Battery 2.875,1.792 3.229,2 0.354,0.208 10 false F82 2.042,1.188 2.396,1.396 0.354,0.208 10 false HTR 2.875,1.958 4.333,2.375 1.458,0.417 10 false Blower Motor with Fan Sub-assembly 3.01,0.927 3.365,1.135 0.354,0.208 10 false 3 4.125,1.24 4.479,1.448 0.354,0.208 10 false 1 4.135,0.625 4.49,0.833 0.354,0.208 10 false 2 5.313,0.615 5.667,0.823 0.354,0.208 10 false 22 3.167,1 3.521,1.208 0.354,0.208 10 false +B 3.906,0.708 4.26,0.917 0.354,0.208 10 false SI 3.75,1.354 4.125,1.563 0.375,0.208 10 false GND 5.552,0.698 5.927,0.906 0.375,0.208 10 false BLW 5.344,3.313 5.719,3.521 0.375,0.208 10 false F80 5.354,3.479 6.938,3.99 1.583,0.51 10 false Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Blower Motor Blower motor with fan sub-assembly Min.: 0
Max.: 31
-
Body Electrical > Air Conditioner > Active Test
Tester Display
Blower Motor
50004 121 2

Result:
Result Proceed to
OK A
NG (Blower motor with fan sub-assembly does not operate) B
NG (Blower motor with fan sub-assembly operates but does not change speed) C



A

B

2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BODY GROUND)

C

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the F82 blower motor with fan sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F82-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BATTERY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F82-3 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
a.

Disconnect the F80 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F80-22 (BLW) - F82-2 (SI) Always Below 1 Ω
F80-22 (BLW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY
a.

Reconnect the F82 blower motor with fan sub-assembly connector.


b.
E285438C01
1.375,0.25 1.771,0.458 0.396,0.208 1.198,1.917 0.917,1.51 false 0.188,0.208 0.5,0.406 0.313,0.198 10 false *a 1.25,1.823 1.781,2.031 0.531,0.208 10 false BLW 1.438,0.271 1.896,0.469 0.458,0.198 10 false F80
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F80-22 (BLW) - Body ground Always 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Reconnect the F80 air conditioning amplifier assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the blower switch on (LO).


d.
E285439C01
1.958,0.656 2.313,0.885 0.354,0.229 2.323,2 2.656,1.438 false 0.198,0.219 0.51,0.417 0.313,0.198 10 false *a 2.021,0.698 2.458,0.948 0.438,0.25 10 false F80 2.823,3.938 3.26,4.188 0.438,0.25 10 false GND 2.125,2.073 2.563,2.323 0.438,0.25 10 false BLW
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the waveform between terminal F80-22 (BLW) of the air conditioning amplifier assembly and body ground.

OK:

Waveform is similar to that shown in the illustration.


HINT:

The waveform varies with the blower speed.


Item Content
Tool Setting 1 V/DIV., 500 μs./DIV.
Vehicle Condition
·

Ignition switch ON

·

Blower switch: LO




Result:
Proceed to
OK
NG



OK

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY