Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM3160E _58 Vehicle Interior _019714 HEATING / AIR CONDITIONING _0109952 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1457  Driver Side Air Outlet Damper Control Servo Motor Circuit  


DESCRIPTION

The rear air mix damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear air mix damper servo sub-assembly to the appropriate position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the rear side is controlled.

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the No. 2 air conditioning harness assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1457 Driver Side Air Outlet Damper Control Servo Motor Circuit Rear air mix damper position sensor value does not change even if air conditioning amplifier assembly operates rear air mix damper servo sub-assembly
·

Rear air mix damper servo sub-assembly

·

No. 2 air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized
(30 sec. or more)*1

*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E235146E05
5.354,2.75 6.927,3.26 1.573,0.51 10 false Air Conditioning Amplifier Assembly 2.396,2.771 3.76,3.281 1.365,0.51 10 false No. 2 Air Conditioning Harness Assembly 0.542,2.594 1.844,3.146 1.302,0.552 10 false Rear Air Mix Damper Servo Sub-assembly 5.104,0.698 5.417,0.927 0.313,0.229 10 false 25 5.094,1.292 5.406,1.49 0.313,0.198 10 false 27 3.854,0.698 4.167,0.896 0.313,0.198 10 false 2 5.365,2.073 6,2.292 0.635,0.219 10 false R BUS 5.375,1.427 6.01,1.646 0.635,0.219 10 false R BBU 5.354,0.781 5.99,1 0.635,0.219 10 false R BUG 3.344,0.792 3.979,1.01 0.635,0.219 10 false R BUG 3.344,1.438 3.979,1.656 0.635,0.219 10 false R BBU 3.344,2.042 3.979,2.26 0.635,0.219 10 false R BUS 5.167,1.948 5.479,2.146 0.313,0.198 10 false 1 3.865,1.292 4.177,1.49 0.313,0.198 10 false 4 3.854,1.969 4.031,2.177 0.177,0.208 10 false 3 5.354,2.583 5.99,2.802 0.635,0.219 10 false F81 2.396,2.594 3.031,2.813 0.635,0.219 10 false L20

CAUTION / NOTICE / HINT

HINT:

Confirm that no mechanical problems are present because this DTC can be output when either a damper link or damper is mechanically locked.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Operate the rear passenger side temperature adjustment switch.


e.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Air Mix Servo Targ Pls(F&R D) Rear air mix damper servo sub-assembly target pulse Min.: 128
Max.: 383
·

MAX COLD: 9 (pulse)

·

MAX HOT: 54 (pulse)


-
A/M Servo Actual Pulse(F&R D) Rear air mix damper servo sub-assembly actual pulse Min.: 128
Max.: 383
·

MAX COLD: 9 (pulse)

·

MAX HOT: 54 (pulse)


-
Body Electrical > Air Conditioner > Data List
Tester Display
Air Mix Servo Targ Pls(F&R D)
A/M Servo Actual Pulse(F&R D)
50003 121 94,147
OK:

When the rear passenger side temperature adjustment switch is turned from MAX COLD to MAX HOT, the actual pulse changes following the target pulse.



Result:
Result Proceed to
Target pulse changes but actual pulse does not change A
Target pulse and actual pulse do not change B
Actual pulse changes following the target pulse (When troubleshooting according to the DTC) C
Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) D



A

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 2 AIR CONDITIONING HARNESS ASSEMBLY)

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

5.RECONFIRM DTC OUTPUT

D

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 2 AIR CONDITIONING HARNESS ASSEMBLY)
a.

Disconnect the L20 No. 2 air conditioning harness assembly connector.


b.

Disconnect the F81 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-27 (R BBU) - L20-4 (R BBU) Always Below 1 Ω
F81-1 (R BUS) - L20-3 (R BUS) Always Below 1 Ω
F81-25 (R BUG) - L20-2 (R BUG) Always Below 1 Ω
F81-27 (R BBU) - Body ground Always 10 kΩ or higher
F81-1 (R BUS) - Body ground Always 10 kΩ or higher
F81-25 (R BUG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE REAR AIR MIX DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE REAR AIR MIX DAMPER SERVO SUB-ASSEMBLY
a.

Replace the rear air mix damper servo sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1457 is output A
DTC B1457 is not output B



A

4.REPLACE NO. 2 AIR CONDITIONING HARNESS ASSEMBLY

B

END (REAR AIR MIX DAMPER SERVO SUB-ASSEMBLY WAS DEFECTIVE)

4.REPLACE NO. 2 AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the No. 2 air conditioning harness assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the No. 2 air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the No. 2 air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1457 is output A
DTC B1457 is not output B



A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

END (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)

5.RECONFIRM DTC OUTPUT
a.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1457 is output A
DTC B1457 is not output B



A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B