Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM3160E _58 Vehicle Interior _019714 HEATING / AIR CONDITIONING _0109952 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Rear Blower Motor Circuit  


DESCRIPTION

The rear blower motor with fan sub-assembly is operated by signals from the air conditioning amplifier assembly. Rear blower motor speed signals are transmitted in accordance with changes in the duty ratio.

WIRING DIAGRAM

E285451E01
0.281,0.688 2.115,0.885 1.833,0.198 10 false from Battery 0.563,2.115 2.396,2.313 1.833,0.198 10 false L18 0.573,2.281 2.031,2.792 1.458,0.51 10 false Rear Blower Motor with Fan Sub-assembly 2.938,1.802 4.771,2 1.833,0.198 10 false L19 2.938,1.958 4.396,2.469 1.458,0.51 10 false Blower Motor Control 5.313,3.281 7.146,3.479 1.833,0.198 10 false F81 5.302,3.458 6.865,3.875 1.563,0.417 10 false Air Conditioning Amplifier Assembly 5.573,0.708 6.188,0.906 0.615,0.198 10 false BLWH 5.292,0.594 5.906,0.792 0.615,0.198 10 false 26 4.146,0.583 4.76,0.781 0.615,0.198 10 false 3 4.146,1.219 4.76,1.417 0.615,0.198 10 false 6 2.99,0.583 3.604,0.781 0.615,0.198 10 false 1 3,1.229 3.615,1.427 0.615,0.198 10 false 2 2.281,1.885 2.896,2.083 0.615,0.198 10 false 2 2.271,2.51 2.885,2.708 0.615,0.198 10 false 1 1.99,0.854 2.531,1.156 0.542,0.302 10 false A/C RR 3.188,0.719 3.802,0.917 0.615,0.198 10 false +B 3.198,1.354 3.813,1.552 0.615,0.198 10 false VM 3.885,0.729 4.5,0.927 0.615,0.198 10 false SI 3.729,1.365 4.344,1.563 0.615,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Blower Motor Rear blower motor with fan sub-assembly Min.: 0
Max.: 31
-
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Blower Motor
50004 121 35

Result:
Result Proceed to
OK A
NG (Rear blower motor with fan sub-assembly does not operate) B
NG (Rear blower motor with fan sub-assembly operates but does not change speed) C



A

B

2.INSPECT REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY

C

9.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
2.INSPECT REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY
a.

Disconnect the L18 rear blower motor with fan sub-assembly connector.


b.
E168786C01
1.375,0.677 1.76,0.938 0.385,0.26 0.615,1.323 1.542,1.99 false 2.427,1.333 1.656,1.99 false 0.156,0.115 0.469,0.271 0.313,0.156 10 false *a 0.521,1.146 0.76,1.375 0.24,0.229 10 false 2 2.479,1.198 2.719,1.427 0.24,0.229 10 false 1 1.448,0.729 1.906,0.927 0.458,0.198 10 false L18
*a Component without harness connected
(Rear Blower Motor with Fan Sub-assembly)


Connect a positive (+) lead from the battery to terminal 2 and a negative (-) lead to terminal 1, and check that the motor operates.

OK:

The rear blower motor with fan sub-assembly operates smoothly.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - BODY GROUND)

NG

REPLACE REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - BODY GROUND)
a.

Disconnect the L19 blower motor control connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L19-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - BATTERY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L19-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L19-2 (VM) - L18-2 Always Below 1 Ω
L19-2 (VM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L18-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F81 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-26 (BLWH) - L19-3 (SI) Always Below 1 Ω
F81-26 (BLWH) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BLOWER MOTOR CONTROL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BLOWER MOTOR CONTROL
a.

Reconnect the L19 blower motor control connector.


b.
E285456C01
1.448,0.729 1.844,0.969 0.396,0.24 1.927,2.583 2.344,2.167 false 0.281,0.271 0.594,0.469 0.313,0.198 10 false *a 1.521,0.771 1.906,1.021 0.385,0.25 10 false F81 1.646,2.635 2.26,2.833 0.615,0.198 10 false BLWH
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F81-26 (BLWH) - Body ground Always 6.0 to 7.0 V



Result:
Proceed to
OK
NG



OK

9.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

9.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Reconnect the F81 air conditioning amplifier assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the rear blower switch on (LO).


d.
E285439C02
0.583,0.646 0.917,0.875 0.333,0.229 1.021,2.021 0.469,1.438 false 0.198,0.219 0.51,0.417 0.313,0.198 10 false *a 0.635,0.677 1.167,0.958 0.531,0.281 10 false F81 0.885,2.063 1.417,2.344 0.531,0.281 10 false BLWH 2.823,3.948 3.354,4.229 0.531,0.281 10 false GND
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the waveform between terminal F81-26 (BLWH) of the air conditioning amplifier assembly and body ground.

OK:

Waveform is similar to that shown in the illustration.


HINT:

The waveform varies with the blower level.


Item Content
Tool Setting 1 V/DIV., 500 μs./DIV.
Vehicle Condition
·

Ignition switch ON

·

Rear blower switch: LO




Result:
Proceed to
OK
NG



OK

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY