Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY
RM3160E _52 Drivetrain _019687 AXLE AND DIFFERENTIAL _0109983 REAR DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Use an overhaul stand as necessary.


PROCEDURE

Hide 1.SEPARATE ELECTRO MAGNETIC CONTROL COUPLING WIRE HARNESS

C223319

a.

Disengage the claw and separate the electro magnetic control coupling wire harness from the 2 clamps.


Hide 2.REMOVE CONNECTOR BRACKET

a.
C230086
1.042,1.469 0.656,1.469 true 2.125,1.073 1.854,1.073 false 0.5,1.385 0.813,1.583 0.313,0.198 10 false *1 1.708,0.979 2.021,1.177 0.313,0.198 10 false *1
*1 Clamp


Remove the 3 bolts and 2 connector brackets from the rear differential carrier assembly.


b.

Remove the 2 clamps from the 2 connector brackets.


Hide 41110H 3.REMOVE REAR DIFFERENTIAL FILLER PLUG

a.
C201222

Remove the rear differential filler plug and gasket.


Hide 41303 4.INSPECT RUNOUT OF ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY

a.
C295937C01
2.115,2.979 2.115,3.802 true 0.292,0.24 0.604,0.438 0.313,0.198 10 false *a 1.927,0.229 2.24,0.427 0.313,0.198 10 false *b 2,3.833 2.458,4.031 0.458,0.198 10 false SST
*a Vertical Runout
*b Lateral Runout


Install a dial indicator and magnetic base perpendicular to the inner side of the electro magnetic control coupling sub-assembly as shown in the illustration.


b.

Using SST, rotate the electro magnetic control coupling sub-assembly forward and backward, and measure the vertical runout.

SST
09564-32011  

Maximum Runout:

0.06 mm (0.00236 in.)


If the runout is greater than the maximum value, replace the electro magnetic control coupling sub-assembly.


c.

Install a dial indicator and magnetic base perpendicular to the electro magnetic control coupling sub-assembly as shown in the illustration.


d.

Using SST, rotate the electro magnetic control coupling sub-assembly forward and backward, and measure the lateral runout.

SST
09564-32011  

Maximum Runout:

0.07 mm (0.00276 in.)


If the runout is greater than the maximum value, replace the electro magnetic control coupling sub-assembly.


Hide 41108C 5.REMOVE REAR DIFFERENTIAL CARRIER COVER BREATHER PLUG

a.
C201223

Using a screwdriver, remove the rear differential carrier cover breather plug.


Hide 6.REMOVE STUD BOLT

C295955
1.344,2.677 1.344,2.865 1.344,2.865 1.865,2.865 false 1.583,2.229 1.583,2.042 1.583,2.042 1.927,2.042 false 1.906,2.781 2.219,2.938 0.313,0.156 10 false *a 1.958,1.958 2.271,2.115 0.313,0.156 10 false *b 0.865,0.281 1.177,0.438 0.313,0.156 10 false *c 2.479,1.156 2.792,1.313 0.313,0.156 10 false *d
*a Upper Nut
*b Lower Nut
*c Turn
*d Hold


a.

Install 2 service nuts to the stud bolt.

Recommended Service Nut:
Thread Diameter:

10 mm (0.394 in.)

Thread Pitch:

1.0 mm (0.0394 in.)



b.

Lock the upper nut using the lower nut.


c.

Turn the lower nut and remove the other 3 stud bolts in the same way.

NOTICE:

Prevent foreign matter from entering the electro magnetic control coupling sub-assembly.


HINT:

If the threads of the electro magnetic control coupling sub-assembly are damaged while removing the stud bolt, replace the electro magnetic control coupling sub-assembly with a new one.



Hide 41303 7.REMOVE ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY

a.
C295957

Remove the 4 bolts.


b.

Using a plastic hammer, lightly tap the electro magnetic control coupling sub-assembly to remove it from the rear differential carrier assembly.

NOTICE:

Do not damage the contact surface.



Hide 41252 8.REMOVE REAR DIFFERENTIAL DUST DEFLECTOR

a.
C295938
2.427,1.594 2.156,1.594 2.156,1.594 1.698,1.042 false 1.156,1.146 0.625,1.229 0.625,1.229 1.146,1.188 true 2.448,1.5 2.76,1.698 0.313,0.198 10 false *a 0.479,1.135 0.792,1.333 0.313,0.198 10 false *b
*a Protective Tape
*b Matchmark


Put matchmarks on the rear differential dust deflector and electro magnetic control coupling sub-assembly.


b.

Using a screwdriver, remove the rear differential dust deflector.

NOTICE:
·

Pry around the circumference of the rear differential dust deflector uniformly to prevent deformation.

·

Do not damage the end surface of the electro magnetic control coupling sub-assembly.



HINT:
·

Tape the screwdriver tip before use.

·

If the end surface of the electro magnetic control coupling sub-assembly is damaged while removing the rear differential dust deflector, replace the electro magnetic control coupling sub-assembly with a new one.




Hide 41330E 9.REMOVE TRANSMISSION COUPLING CONICAL SPRING WASHER

a.
C198087
0.801,0.541 0.984,0.729 0.183,0.189 10 *1 1.896,0.632 1.006,0.632 false
*1 Transmission Coupling Conical Spring Washer


Remove the transmission coupling conical spring washer from the rear differential carrier assembly.


Hide 41330H 10.REMOVE TRANSMISSION COUPLING SPACER

a.
C198088
1.027,0.322 1.238,0.548 0.212,0.226 10 *1 1.964,0.4 1.248,0.4 false
*1 Transmission Coupling Spacer


Remove the transmission coupling spacer from the rear differential carrier assembly.


Hide 11.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C202763N02
0.844,1.708 0.74,1.604 0.74,1.604 0.542,1.604 false 1.135,3.042 1.708,3.042 true 0.25,1.51 0.594,1.729 0.344,0.219 10 false SST 1.76,2.958 2.135,3.188 0.375,0.229 10 false SST

Insert a dial indicator and magnetic base through the rear differential filler plug hole, and set it perpendicular to a differential ring gear tooth tip.


b.

Using SST, hold the differential drive pinion in place.

SST
09556-16011  


c.

Using SST, rotate the rear differential case assembly forward and backward, and measure the backlash.

SST
09564-32011  

Backlash:

0.13 to 0.25 mm (0.00512 to 0.00984 in.)


If the backlash is not within the specification, adjust the side bearing preload or repair as necessary.

HINT:

Measure at 3 or more areas on the circumference of the differential ring gear.



Hide 12.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C201986
2.417,0.813 1.979,0.813 false 2.469,0.719 2.854,0.927 0.385,0.208 10 false SST

Using SST and a torque wrench, inspect the differential drive pinion preload (starting torque) of the backlash between the differential drive pinion and differential ring gear.

SST
09556-16011  

Standard Drive Pinion Preload:

1.51 to 2.52 N*m (16 to 25 kgf*cm, 14 to 22 in.*lbf)


If the differential drive pinion preload is not within the specified range, adjust the differential drive pinion preload or repair as necessary.

HINT:

For a more accurate measurement, rotate the rear differential case bearing forward and backward before measuring.



Hide 13.INSPECT TOTAL PRELOAD

a.
C201986
2.417,0.813 1.979,0.813 false 2.469,0.719 2.854,0.927 0.385,0.208 10 false SST

Using SST and a torque wrench, inspect the total preload (starting torque) with the teeth of the differential drive pinion and differential ring gear in contact.

SST
09556-16011  

Standard Total Preload:

2.80 to 5.34 N*m (29 to 54 kgf*cm, 25 to 47 in.*lbf)


If the total preload is not within the specified range, adjust the total preload or repair as necessary.

HINT:

For a more accurate measurement, rotate the rear differential case bearing forward and backward before measuring.



Hide 42340D 14.REMOVE REAR DRIVE SHAFT OIL SEAL LH

a.
C202761
1.615,1.188 1.615,1.583 false 1.49,1.625 1.844,1.823 0.354,0.198 10 false SST

Using SST, remove the rear drive shaft oil seal LH from the rear differential carrier assembly.

SST
09308-00010  


Hide 42330G 15.REMOVE REAR DRIVE SHAFT OIL SEAL RH

HINT:

Use the same procedure for the RH side and LH side.


Hide 41410D 16.REMOVE DIAPHRAGM OIL SEAL

a.
C201989
1.302,0.854 1.667,0.49 1.667,0.49 1.813,0.49 false 2.063,1.094 2.229,1.094 false 2.219,1.521 1.99,1.521 false 1.854,0.396 2.188,0.635 0.333,0.24 10 false SST 1.781,1.01 2.104,1.229 0.323,0.219 10 false SST 1.823,1.427 2.042,1.615 0.219,0.188 10 false *1
*1 Diaphragm Oil Seal


Using SST, remove the diaphragm oil seal from the rear differential carrier assembly.

SST
09308-00010  


Hide 41204B 17.REMOVE REAR DRIVE PINION NUT

a.
C155238
0.875,0.646 1.323,0.646 false 2.646,1.5 2.302,0.99 2.302,0.99 2.094,0.99 true 0.583,0.563 1.229,0.802 0.646,0.24 10 false SST 1.927,0.896 2.24,1.094 0.313,0.198 10 false *1
*1 Rear Drive Pinion Nut


Using SST and a hammer, release the staked part of the rear drive pinion nut.

SST
09930-00010  

NOTICE:
·

Use SST with the tapered part facing against the shaft.

·

Do not modify the SST tip with a grinder or equivalent.

·

Loosen the staked part of the rear drive pinion nut completely, otherwise the threads of the differential drive pinion may be damaged.




b.
C155239
1.458,1.063 0.875,1.625 true 2.302,0.552 1.594,0.552 true 0.271,0.792 0.625,0.979 0.354,0.188 10 false *a 2.448,0.885 2.792,1.073 0.344,0.188 10 false *b 0.563,1.573 0.927,1.729 0.365,0.156 10 false SST 2.333,0.469 2.698,0.625 0.365,0.156 10 false SST
*a Hold
*b Turn


Using SST, hold the differential drive pinion in place and remove the rear drive pinion nut from the differential drive pinion.

SST
09556-16011  09564-16020  


Hide 41201B 18.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C201992
0.521,1.125 0.948,1.125 true 3.073,1.458 3.073,1.313 3.073,1.313 2.844,1.094 true 2.25,1.927 2.25,1.625 true 0.229,1.052 0.573,1.281 0.344,0.229 10 false SST 2.927,1.469 3.26,1.646 0.333,0.177 10 false SST 2.167,1.948 2.406,2.135 0.24,0.188 10 false *1 0.323,0.677 0.563,0.865 0.24,0.188 10 false *a 1.885,0.573 2.125,0.76 0.24,0.188 10 false *b
*1 Rear Drive Pinion Front Tapered Roller Bearing (Inner Race)
*a Hold
*b Turn


Using SST, remove the rear drive pinion front tapered roller bearing (inner race) from the differential drive pinion.

SST
09556-40010  


Hide 19.REMOVE DIFFERENTIAL SIDE BEARING RETAINER

a.
C201227

Remove the 10 bolts from the rear differential carrier.


b.
C201228

Using a brass bar and a hammer, disengage the 2 pins and remove the differential side bearing retainer from the rear differential carrier.

NOTICE:
·

Set the brass bar on the ribbed part of the differential side bearing retainer.

·

Do not damage the contact surface.




Hide 20.REMOVE REAR DIFFERENTIAL CASE ASSEMBLY

a.
C201990

Remove the rear differential case assembly from the rear differential carrier.


Hide 41183 21.REMOVE REAR DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR

a.
C201231

Remove the 2 bolts and rear differential breather plug oil deflector from the rear differential carrier.


Hide 22.REMOVE DIFFERENTIAL DRIVE PINION

a.
C201991

Remove the differential drive pinion from the rear differential carrier.


Hide 41214 23.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

C095831

a.

Remove the rear differential drive pinion oil slinger from the differential drive pinion.


Hide 41231 24.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C095832

Remove the rear differential drive pinion bearing spacer from the differential drive pinion.


Hide 41201A 25.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C155244
0.875,1.917 0.875,1.635 false 0.74,1.927 1.094,2.115 0.354,0.188 10 false SST

Using SST and a press, press out the rear drive pinion rear tapered roller bearing (inner race) from the differential drive pinion.

SST
09950-00020  

NOTICE:
·

Do not drop the differential drive pinion.

·

If the rear differential driver pinion or differential ring gear is damaged, replace them both.




b.

Remove the rear differential drive pinion plate washer.


Hide 41201B 26.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C202760
0.531,1.427 0.854,1.427 false 2.427,2.594 2.281,2.75 2.281,2.75 2.281,3.01 true 1.313,2.99 1.313,2.24 true 0.24,1.344 0.604,1.542 0.365,0.198 10 false SST 2.198,3.042 2.438,3.25 0.24,0.208 10 false *1 0.177,0.427 0.417,0.635 0.24,0.208 10 false *a 2.719,0.771 2.958,0.979 0.24,0.208 10 false *b 1.188,3.021 1.552,3.219 0.365,0.198 10 false SST
*1 Rear Drive Pinion Front Tapered Roller Bearing (Outer Race)
*a Hold
*b Turn


Using SST, remove the rear drive pinion front tapered roller bearing (outer race) from the rear differential carrier.

SST
09387-00041  (09387-01030, 09387-01041)
09387-02020  


Hide 41201A 27.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C201994

Using a brass bar and a hammer, lightly and uniformly tap out the rear drive pinion rear tapered roller bearing (outer race) from the rear differential carrier.

NOTICE:

Set the brass bar on the notch.



Hide 41301A 28.REMOVE REAR DIFFERENTIAL CASE BEARING (for LH Side)

a.
C201996
1.74,1.156 2.042,1.156 2.042,1.156 2.042,1.688 true 1.823,1.271 2.042,1.271 true 2.521,0.865 2.521,1.417 true 2.958,0.781 2.958,1.323 true 1.917,1.719 2.302,1.958 0.385,0.24 10 true SST 2.896,1.354 3.115,1.552 0.219,0.198 10 false *2 2.438,1.448 2.677,1.615 0.24,0.167 10 false *1
*1 Rear Differential Case Bearing (Outer Race)
*2 Rear Differential Side Gear Shaft Plate Washer


Using SST and a press, remove the rear differential case bearing (LH side outer race) and rear differential side gear shaft plate washer from the differential side bearing retainer.

SST
09950-60010  (09951-00540)
09950-70010  (09951-07100)


Hide 41301A 29.REMOVE REAR DIFFERENTIAL CASE BEARING (for RH Side)

a.
C201995
1.188,1.042 1.063,1.042 1.063,1.042 1.063,0.552 true 1.26,0.552 0.844,0.552 false 2.146,1.021 2.146,1.406 true 2.74,0.875 2.74,1.354 true 2.083,1.417 2.302,1.635 0.219,0.219 10 false *1 2.677,1.385 2.927,1.594 0.25,0.208 10 false *2 0.563,0.479 0.917,0.677 0.354,0.198 10 false SST
*1 Rear Differential Case Bearing (Outer Race)
*2 Rear Differential Side Gear Shaft Plate Washer


Using SST and a press, remove the rear differential case bearing (RH side outer race) and rear differential side gear shaft plate washer from the rear differential carrier.

SST
09950-60010  (09951-00590)
09950-70010  (09951-07100)


Hide 30.REMOVE STRAIGHT PIN

a.

Remove the 4 straight pins from the rear differential carrier.

C201229


Hide 41301A 31.REMOVE REAR DIFFERENTIAL CASE BEARING (for LH Side)

HINT:

Perform this step only when replacing the rear differential case bearing or rear differential case sub-assembly.


a.
C201998
1.229,0.99 1.583,0.99 false 0.938,1.667 1.281,1.667 false 1.01,2.938 1.01,3.021 1.01,3.021 1.385,3.021 true 0.948,0.906 1.313,1.115 0.365,0.208 10 false SST 1.313,1.594 1.635,1.771 0.323,0.177 10 false SST 1.406,2.948 1.677,3.188 0.271,0.24 10 false *1 0.938,0.281 1.208,0.521 0.271,0.24 10 false *a 3.156,1.708 3.427,1.948 0.271,0.24 10 false *b
*1 Rear Differential Case Bearing (LH Side Inner Race)
*a Hold
*b Turn


Using SST, remove the rear differential case bearing (LH side inner race) from the rear differential case sub-assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)
09950-60010  (09951-00340)

NOTICE:

Before using the SST center bolt (09953-04020), apply grease to its threads and tip.


HINT:
·

If the race remains on the rear differential case sub-assembly, repeat the step above to remove the race.

·

If the rear differential case bearing (LH side inner race) is deformed, replace it with a new one.




Hide 41301A 32.REMOVE REAR DIFFERENTIAL CASE BEARING (for RH Side)

HINT:

Perform this step only when replacing the rear differential case bearing or rear differential case sub-assembly.


a.
C201997
1.5,1.01 1.135,1.01 false 0.938,1.656 1.281,1.656 false 1.01,2.802 1.01,2.906 1.01,2.906 1.271,2.906 true 0.865,0.927 1.24,1.125 0.375,0.198 10 false SST 1.302,2.823 1.531,3.042 0.229,0.219 10 false *1 1.313,1.583 1.625,1.792 0.313,0.208 10 false SST 0.948,0.229 1.177,0.448 0.229,0.219 10 false *a 3.115,1.667 3.344,1.885 0.229,0.219 10 false *b
*1 Rear Differential Case Bearing (RH Side Inner Race)
*a Hold
*b Turn


Using SST, remove the rear differential case bearing (RH side inner race) from the rear differential case sub-assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00370)

NOTICE:

Before using the SST center bolt (09953-04020), apply grease to its threads and tip.


HINT:
·

If the race remains on the rear differential case sub-assembly, repeat the step above to remove the race.

·

If the rear differential case bearing (RH side inner race) is deformed, replace it with a new one.




Hide 33.REMOVE DIFFERENTIAL RING GEAR

a.
C201999C01
1.542,1.292 1.656,1.292 1.656,1.292 1.656,1.656 true 1.542,1.354 1.646,1.354 true 1.573,1.656 1.854,1.906 0.281,0.25 10 true *a
*a Matchmark


Secure the rear differential case sub-assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Put matchmarks on the rear differential case sub-assembly and differential ring gear.


c.

Remove the 12 rear differential case bolts.


d.

Using a plastic hammer, lightly and uniformly tap the outer circumference of the differential ring gear to remove it from the rear differential case sub-assembly.

NOTICE:
·

Do not drop the differential ring gear.

·

If the differential drive pinion or differential ring gear is damaged, replace them both.



HINT:

If it is difficult to remove, tap the outer circumference of the differential ring gear using a brass bar and a hammer.



Hide 34.INSPECT DIFFERENTIAL PINION AND SIDE GEAR

a.

Check the differential pinion gears and differential side gears for wear.

If the differential pinion gears and differential side gears are damaged, replace the rear differential case sub-assembly.


Hide 35.INSPECT DIFFERENTIAL CASE

a.

Check the differential case for cracks or damage.

If the differential case is damaged, replace the rear differential case sub-assembly.