Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL MOUNT CUSHION
RM3160E _52 Drivetrain _019687 AXLE AND DIFFERENTIAL _0109984 DIFFERENTIAL MOUNT CUSHION A

AXLE AND DIFFERENTIAL  DIFFERENTIAL MOUNT CUSHION  REPLACEMENT  


PROCEDURE

Hide 1.REMOVE SPARE TIRE

Hide 2.REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

Hide 41651A 3.REMOVE REAR NO. 2 DIFFERENTIAL MOUNT CUSHION

a.

Using SST, remove the rear No. 2 differential mount cushion.

SST
09570-48010  

C204711C01
5.677,2.188 5.677,2.531 5.677,2.531 6.51,2.531 false 6.24,2.219 6.24,2.531 false 1.26,0.979 1.052,0.979 1.052,0.979 0.948,1.083 false 1.302,0.896 1.635,1.094 0.333,0.198 10 false SST 6.563,2.438 6.917,2.667 0.354,0.229 10 false SST 5.417,0.875 5.646,1.083 0.229,0.208 10 false *a
*a Front of the Vehicle - -


NOTICE:
·

Before using SST, apply grease to the SST bolts.

·

Be sure to use the correct combination of SST.

·

Be sure to use the correct direction of SST.

·

Make sure that SST contacts the entire circumference of the rear No. 2 differential mount cushion.

·

Do not tilt the bolts of SST.

·

Tighten the 2 bolts of SST so that they enter the 2 holes of the rear No. 2 differential mount cushion by an equal amount.




Hide 41651A 4.INSTALL REAR NO. 2 DIFFERENTIAL MOUNT CUSHION

a.

Using SST, install a new rear No. 2 differential mount cushion.

SST
09570-48010  

C204712C01
6.177,1.292 6.542,1.292 true 6.323,2.292 6.323,2.115 6.323,2.115 6.594,2.115 false 6.479,2.333 6.479,2.115 false 1.229,0.99 1.031,0.99 1.031,0.99 0.948,1.073 false 1.271,0.906 1.563,1.063 0.292,0.156 10 false SST 6.292,3.24 6.5,3.438 0.208,0.198 10 false A 6.031,0.302 6.24,0.5 0.208,0.198 10 false *a 6.573,1.198 6.802,1.438 0.229,0.24 10 false *b 6.625,2.031 6.917,2.188 0.292,0.156 10 false SST 5.49,2.052 5.698,2.25 0.208,0.198 10 false *c
*a 0° +/- 3° *b Protrusion
*c Front of the Vehicle - -


Standard Distance (A):

9.8 to 10.8 mm (0.386 to 0.425 in.)


NOTICE:
·

Make sure that the rear No. 2 differential mount cushion is aligned within 3° from the center.

·

Install the rear No. 2 differential mount cushion so that the protrusion is positioned as shown in the illustration.

·

Temporarily install the rear No. 2 differential mount cushion to the rear suspension member sub-assembly in order to prevent it from tilting, and then install SST.

·

Before using SST, apply grease to the SST bolt.

·

Be sure to use the correct combination of SST.

·

Be sure to use the correct direction of SST.

·

Make sure that SST contacts the entire circumference of the rear No. 2 differential mount cushion.

·

Do not tilt the bolts of SST.

·

Tighten the 2 bolts of SST so that they enter the 2 holes of the rear No. 2 differential mount cushion by an equal amount.




Hide 5.INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

Hide 6.INSTALL SPARE TIRE