Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0110063 LANE DEPARTURE ALERT SYSTEM U

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Lane Departure Alert / Data List.


e.

Read the Data List according to the display on the GTS.

Chassis > Lane Departure Alert > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
LDA Control Status of the LDA control Prohibit or Permit Prohibit: Lane departure alert system operation prohibited
Permit: Lane departure alert system operation permitted
-
Head Light (High Beam) Status of the head light (high beam) OFF or ON ON: Headlight dimmer switch HI
OFF: Headlight dimmer switch except HI
-
Turn Signal Switch (Right) Status of turn signal light switch (right) OFF or ON ON: Turn signal light switch on (right)
OFF: Turn signal light switch off
-
Turn Signal Switch (Left) Status of turn signal light switch (left) OFF or ON ON: Turn signal light switch on (left)
OFF: Turn signal light switch off
-
Destination Information Status of the country JPN, NA, EURO, CHINA or OTHER Actual country code -
LDA Indicator Status of the lane departure alert indicator Nothing or Green Nothing: Lane departure alert indicator not displayed
Green: Lane departure alert indicator displayed
-
Left Lane Indicator Status of left lane indicator Nothing, Heavy, Thin or H blink Nothing: Lane departure alert system deactivated
Heavy: Left lane detected
Thin: Left lane not detected
H blink: Departing from left lane
-
Right Lane Indicator Status of right lane indicator Nothing, Heavy, Thin or H blink Nothing: Lane departure alert system deactivated
Heavy: Right lane detected
Thin: Right lane not detected
H blink: Departing from right lane
-
Skid Control Buzzer Demand Status of skid control buzzer assembly*1 or lane departure warning buzzer*2 demand OFF or ON OFF: Skid control buzzer assembly*1 or lane departure warning buzzer*2 does not sound (lane departure warning is not being issued)
ON: Skid control buzzer assembly*1 or lane departure warning buzzer*2 sounds (lane departure warning is being issued)
-
The Number of DTCs Number of DTCs min.: 0, max.: 255 Actual number of DTCs -

*1: w/ Dynamic Radar Cruise Control System

*2: w/o Dynamic Radar Cruise Control System




ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Lane Departure Alert / Active Test.


e.

Perform Active Test according to the display on the GTS.

HINT:

The engine switch must be turned on to proceed with the Active Test using the GTS.


Chassis > Lane Departure Alert > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
LDA Buzzer Skid control buzzer assembly*1 or lane departure warning buzzer*2 OFF or ON Vehicle condition: Vehicle stopped

*1: w/ Dynamic Radar Cruise Control System

*2: w/o Dynamic Radar Cruise Control System



f.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


g.

Perform Active Test according to the display on the GTS.

HINT:

The engine switch must be turned on to proceed with the Active Test using the GTS.


Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All Confirm that the vehicle is stopped with the engine switch on (IG)