Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0110870 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the driving support ECU assembly. The driving support ECU assembly determines information about the vehicle in front based on data from the radar sensor, and then decides how much acceleration and/or deceleration is needed to maintain the set vehicle-to-vehicle distance. The driving support ECU assembly also requests to apply braking.

WIRING DIAGRAM

E259149
5.958,0.521 6.167,0.76 0.208,0.24 10 false B 5.688,1.292 5.927,1.458 0.24,0.167 10 false 25 5.948,1.438 6.281,1.688 0.333,0.25 10 false GND 5.677,0.406 5.875,0.594 0.198,0.188 10 false 30 5.135,2.208 7.063,2.74 1.927,0.531 10 false Driving Support ECU Assembly 5.146,2.031 5.448,2.177 0.302,0.146 10 false F84 3.719,0.688 4.406,1 0.688,0.313 10 false IG1 NO. 3 1.406,0.521 2.375,0.896 0.969,0.375 10 false from IG1 NO. 3 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
E244596C04
1.552,0.417 1.885,0.635 0.333,0.219 2.469,2.469 1.906,2.469 1.906,2.469 1.771,1.927 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 2.51,2.396 2.708,2.604 0.198,0.208 10 false B 1.594,0.438 1.927,0.604 0.333,0.167 10 false F84
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F84 driving support ECU assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F84-30 (B) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the F84 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the F84 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F84-25 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the F84 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)