Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0110870 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to turn the dynamic radar cruise control system on and off, as well as operate 8 functions: SET, -(COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, CANCEL, and MODE. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while it is being operated in the direction of each arrow and turns off when released. The internal contact points of the cruise control main switch turn on with switch operation. The ECM then reads the voltage value that has been changed by the switch operation to control MODE, SET, -, RES, +, or CANCEL function. The dynamic radar cruise control system has 2 cruise control modes: constant speed control mode and vehicle-to-vehicle distance control mode.

·

Vehicle-to-vehicle distance control mode is selected by default when the dynamic radar cruise control system is turned on using the cruise control main switch (ON-OFF button).

·

The operation of constant speed control mode is the same as that for a conventional cruise control system.


WIRING DIAGRAM

E259146E15
0.448,1.677 1.031,1.927 0.583,0.25 10 false CANCEL 1.333,1.698 1.854,1.958 0.521,0.26 10 false -/SET 2.198,1.625 2.823,1.865 0.625,0.24 10 false +/RES 3.104,1.531 3.729,1.865 0.625,0.333 10 false ON-OFF (MAIN) 3.208,2.375 3.688,2.563 0.479,0.188 10 false MODE 1.052,4.667 2.792,5.042 1.74,0.375 10 false Cruise Control Main Switch 3.969,4.76 4.865,5.292 0.896,0.531 10 false Cruise Control Switch Wire 4.875,4.688 5.969,5.021 1.094,0.333 10 false Spiral Cable Sub-assembly 4.073,1.01 4.198,1.156 0.125,0.146 10 false 4 4.073,2.135 4.198,2.281 0.125,0.146 10 false 3 4.698,0.938 4.823,1.083 0.125,0.146 10 false 3 4.719,3.99 4.844,4.177 0.125,0.188 10 false 4 5.656,4.01 5.792,4.208 0.135,0.198 10 false 2 5.635,2.083 5.781,2.281 0.146,0.198 10 false 8 5.635,0.948 5.76,1.094 0.125,0.146 10 false 1 4.073,4.104 4.198,4.25 0.125,0.146 10 false 1 4.688,2.083 4.813,2.229 0.125,0.146 10 false 1 4.656,1.146 4.917,1.323 0.26,0.177 10 false z8 4.656,2.26 4.906,2.49 0.25,0.229 10 false z8 4.656,4.198 4.938,4.438 0.281,0.24 10 false z8 5.563,4.208 5.844,4.469 0.281,0.26 10 false F61 5.563,2.271 5.833,2.5 0.271,0.229 10 false F61 5.563,1.146 5.865,1.417 0.302,0.271 10 false F61 5.208,1.031 5.531,1.198 0.323,0.167 10 false CCS 6.417,1.146 6.74,1.313 0.323,0.167 10 false CCS 6.406,2.281 6.844,2.448 0.438,0.167 10 false CCHG 6.406,2.979 6.604,3.146 0.198,0.167 10 false E1 5.25,2.135 5.521,2.302 0.271,0.167 10 false R/N 5.198,4.073 5.521,4.24 0.323,0.167 10 false ECC 6.542,3.406 6.906,3.688 0.365,0.281 10 false ECM 6.115,2.073 6.396,2.25 0.281,0.177 10 false 48 6.125,0.948 6.313,1.135 0.188,0.188 10 false 47 6.063,2.26 6.365,2.479 0.302,0.219 10 false A43 6.063,1.146 6.354,1.354 0.292,0.208 10 false A43 6.135,2.781 6.406,2.927 0.271,0.146 10 false 49 6.104,2.948 6.406,3.219 0.302,0.271 10 false C1

PROCEDURE

1.READ VALUE USING GTS (MAIN SW M-CPU, CANCEL SWITCH, SET/COAST SWITCH, RES/ACC SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise / Data List.


e.
A305789C03
2.656,1.198 2.969,1.354 0.313,0.156 10 false *a 0.615,1.75 0.927,1.906 0.313,0.156 10 false *b 1.323,1.844 1.583,2.063 0.26,0.219 10 false *c 1.354,0.24 1.667,0.396 0.313,0.156 10 false *d 2.177,0.292 2.438,0.531 0.26,0.24 10 false *e
*a ON-OFF
*b CANCEL
*c -SET
*d +RES
*e MODE


Check the Data List for proper functioning of the cruise control main switch.

Powertrain > Radar Cruise > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control main switch signal (Main CPU) ON or OFF ON: Cruise control main switch on
OFF: Cruise control main switch off
-
Cancel Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-
Powertrain > Radar Cruise > Data List
Tester Display
Main SW M-CPU
Cancel Switch
SET/COAST Switch
RES/ACC Switch
50003 239 15,22,21,20
OK:

When the cruise control main switch is operated, the display changes as shown in the table.



Result:
Proceed to
OK
NG


f.

Turn the engine switch off.



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

A315698C01
5.323,1.417 5.5,1.833 5.5,1.833 5.75,1.833 false 2.833,3.25 2.833,2.75 2.833,2.75 3,2.75 false 2.604,3.25 2.604,2.75 2.604,2.75 2.438,2.75 false 2.458,3.208 2.458,3.542 2.458,3.542 2.292,3.542 false 5.792,1.75 6.104,1.906 0.313,0.156 10 false *1 1.927,2.708 2.24,2.865 0.313,0.156 10 false *a 6.188,1 6.5,1.156 0.313,0.156 10 false *b 4.542,0.49 4.854,0.646 0.313,0.156 10 false *c 4.781,2.521 5.094,2.677 0.313,0.156 10 false *d 5.677,0.125 5.99,0.281 0.313,0.156 10 false *e 3.927,2.427 4.24,2.583 0.313,0.156 10 false *f 3.042,2.667 3.5,2.865 0.458,0.198 10 false ECC 2.188,2.667 2.646,2.865 0.458,0.198 10 false R/N 1.979,3.469 2.438,3.667 0.458,0.198 10 false CCS
*1 Cruise Control Main Switch (ON-OFF button) - -
*a Component without harness connected
(cruise control main switch)
*b ON-OFF
*c +/RES *d -/SET
*e MODE *f CANCEL


Standard Resistance:
Tester Connection Condition Specified Condition
1 (ECC) - 3 (R/N) Cruise control main switch (ON-OFF button) not pressed 1 MΩ or higher
MODE Below 1.5 Ω
1 (ECC) - 4 (CCS) Cruise control main switch (ON-OFF button) not pressed 1 MΩ or higher
Cruise control main switch (ON-OFF button) pressed Below 1.5 Ω
+/RES 235 to 245 Ω
-/SET 617 to 643 Ω
CANCEL 1509 to 1571 Ω



c.

Reinstall the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSTALLATION


Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL MAIN SWITCH)

NG

3.CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL MAIN SWITCH)
a.
A315700C05
0.333,1.333 0.74,1.615 0.406,0.281 0.396,0.688 0.708,0.906 0.313,0.219 10 false *a 0.5,3.104 0.813,3.302 0.313,0.198 10 false *b 0.469,1.385 0.781,1.583 0.313,0.198 10 false z8 0.125,0.104 0.406,0.281 0.281,0.177 10 false *1
*1 Cruise Control Switch Wire
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Main Switch)


Remove the cruise control switch wire.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z8-4 - Cruise control main switch side connector terminal 1 Always Below 1 Ω
z8-1 - Cruise control main switch side connector terminal 3 Always Below 1 Ω
z8-3 - Cruise control main switch side connector terminal 4 Always Below 1 Ω



c.

Reinstall the cruise control switch wire.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>INSTALLATION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
a.

Disconnect the A43 ECM connector.


b.

Disconnect the F61 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A43-47 (CCS) - F61-1 (CCS) Always 3 Ω or less
A43-48 (CCHG) - F61-8 (R/N) Always 3 Ω or less


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A43-47 (CCS) or F61-1 (CCS) - Body ground Always 1 MΩ or higher
A43-48 (CCHG) or F61-8 (R/N) - Body ground Always 1 MΩ or higher



d.

Reconnect the A43 ECM connector.


e.

Reconnect the F61 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the F61 spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F61-2 (ECC) - Body ground Always Below 1 Ω



c.

Reconnect the F61 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)