Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0110870 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Millimeter Wave Radar Sensor Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), battery voltage is applied to terminal IGB of the millimeter wave radar sensor assembly.

This circuit provides power to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly emits radio waves towards an object in front and measures the distance and direction of the object by receiving the beam reflections. Based on the reflections, the sensor calculates the difference in speed between the vehicle and the object in front. This data is transmitted to the driving support ECU assembly.

WIRING DIAGRAM

E259147
4.052,2.156 4.292,2.333 0.24,0.177 10 false A3 4.979,1.51 5.448,1.667 0.469,0.156 10 false SGND 4.979,0.469 5.333,0.625 0.354,0.156 10 false IGB 4.75,1.354 4.865,1.51 0.115,0.156 10 false 1 4.75,0.333 4.865,0.49 0.115,0.156 10 false 5 4.052,2.354 6.615,2.615 2.563,0.26 10 false Millimeter Wave Radar Sensor Assembly 2.667,0.646 3.219,0.938 0.552,0.292 10 false DSS-IG 0.417,0.448 1.396,0.823 0.979,0.375 10 false from IG1 NO. 3 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (IGB VOLTAGE)
a.
C268297
1.51,0.177 1.844,0.427 0.333,0.25 2.583,0.813 2.313,0.813 2.313,0.813 2,1.156 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 2.656,0.729 3.271,0.927 0.615,0.198 10 false IGB 1.604,0.219 1.917,0.375 0.313,0.156 10 false A3
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A3 millimeter wave radar sensor assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A3-5 (IGB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the A3 millimeter wave radar sensor assembly connector.


f.

Connect the GTS to the DLC3.


g.

Turn the engine switch on (IG).



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A3 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A3-1 (SGND) - Body ground Always Below 1 Ω



c.

Reconnect the A3 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)