Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019711 PRE-CRASH SAFETY _0110871 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  TERMINALS OF ECU  


CHECK DRIVING SUPPORT ECU ASSEMBLY


E158948
3.458,0.188 3.896,0.469 0.438,0.281 3.573,0.24 3.969,0.49 0.396,0.25 10 false F84

a.

Disconnect the F84 driving support ECU assembly connector.

NOTICE:

Do not apply excessive force to the connector. If a force of 10 kg or more is applied, the connector may break.



b.

Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F84-5 (PBSW) - Body ground B - Body ground Pre-crash safety system cancel switch assembly signal Pre-crash safety system cancel switch assembly on Below 1 Ω
Pre-crash safety system cancel switch assembly off 10 kΩ or higher
F84-25 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
F84-30 (B) - Body ground R - Body ground Power source Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the F84 driving support ECU assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
F84-17 (CA2L) - F84-25 (GND) W - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
F84-18 (CA1N) - F84-25 (GND) W - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)
F84-39 (CA2H) - F84-25 (GND) G - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 3)
F84-40 (CA1P) - F84-25 (GND) R - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 4)


e.
E228688
2.99,1.442 3.317,1.617 0.327,0.175 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection F84-17 (CA2L) - F84-25 (GND)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




f.
E228688
2.99,1.442 3.317,1.617 0.327,0.175 10 GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection F84-18 (CA1N) - F84-25 (GND)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




g.
E228691
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 3

i.

CAN communication signal

Item Content
Tester Connection F84-39 (CA2H) - F84-25 (GND)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




h.
E228691
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 4

i.

CAN communication signal

Item Content
Tester Connection F84-40 (CA1P) - F84-25 (GND)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.