Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019711 PRE-CRASH SAFETY _0110871 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wiper Information Wiper operational status Unoperat, Oil off, Mist, Washer, Unknown, Intermi, Lo or Hi The respective operational status displayed -
PCS OFF Switch Pre-crash safety system cancel switch assembly status ON or OFF ON: Pre-crash safety system cancel switch assembly on
OFF: Pre-crash safety system cancel switch assembly off
-
Pre-Crash System Pre-crash safety system control Valid or Inval Valid: Pre-crash safety system control possible
Inval: Pre-crash safety system control not possible
-
PCS Indicator "Check PCS System" display request signal ON or OFF ON: "Check PCS System" display requested
OFF: "Check PCS System" display not requested
-
PCS Disabled Indicator "PCS temporarily not available" display request signal ON or OFF ON: "PCS temporarily not available" display requested
OFF: "PCS temporarily not available" display not requested
-
Pre-Crash Safety Warning Buz Pre-crash safety system warning buzzer Valid or Inval Valid: Pre-crash safety system warning buzzer operation possible
Inval: Pre-crash safety system warning buzzer operation not possible
-
Pre-Crash Brake Pre-crash safety brake function Valid or Inval Valid: Pre-crash safety brake operation possible
Inval: Pre-crash safety brake operation not possible
-
PBA Start Pre-crash safety brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2 OFF: Pre-crash safety brake assist not activated
Standby: Pre-crash safety brake assist standby
Assist Lv1: Pre-crash safety brake assist activated
Assist Lv2: Pre-crash safety brake assist activated
Signal status changes when the pre-crash brake assist is activated before a crash (Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
Brake Assist Standby Supplemental brake pressure signal ON or OFF ON: Supplemental brake pressure being provided
OFF: Supplemental brake pressure not being provided
Signal status changes when supplemental brake pressure is being provided after a crash is judged as unavoidable and before the brake pedal is depressed
Pre-Crash Brake Control Pre-crash safety brake operational status ON or OFF ON: Pre-crash safety brake operating
OFF: Pre-crash safety brake not operating
Status changes when pre-crash safety brake operates before a crash
AVS Start Adaptive variable suspension system control activation status ON or OFF - Unused
CCS Cancel Automatic cancellation of cruise control during pre-collision brake activation ON or OFF ON: Cruise control automatically canceled
OFF: Cruise control not automatically canceled
-
Pre-Crash Safety Brake Ind Pre-crash safety system "BRAKE!" alert status ON or OFF ON: Pre-crash safety system "BRAKE!" alert on
OFF: Pre-crash safety system "BRAKE!" alert off
-
Front Radar-Dirt History Millimeter wave radar sensor assembly dirt history ON or OFF ON: History of excessive dirt
OFF: No history of excessive dirt
-
Front Radar-Environment Hist Millimeter wave radar sensor assembly environment condition history Good or Bad Good: No history of excessive bad environment
Bad: History of excessive bad environment
-
Curr Com PCS-WIL-R Driver seat active headrest ECU connection status with or without with: Driver seat active headrest ECU connected
without: Driver seat active headrest ECU not connected
Not Supported
Curr Com PCS-WIL-L Front passenger seat active headrest ECU connection status with or without with: Front passenger seat active headrest ECU connected
without: Front passenger seat active headrest ECU not connected
Not Supported
Curr Com Night View ECU Night view ECU connection status with or without with: Night view ECU connected
without: Night view ECU not connected
Not Supported
Curr Com Front Camera Module Front camera module connection status with or without with: Front camera module connected
without: Front camera module not connected
Not Supported
Country# (DSS) Destination country for driving support ECU assembly JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC or NOFIX Actual country code -
The Number of DTCs Number of DTCs min: 0, max: 255 Number of DTCs will be displayed -

f.

Read the Data List according to the display on the GTS.


g.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


h.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay (STOP LP relay) output ON or OFF ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Perform Active Test according to the display on the GTS.

HINT:

The engine switch must be turned on (IG) to proceed with the Active Test using the GTS.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON or OFF Buzzer can be heard
PCS Approach Alarm Buzzer Skid control buzzer assembly ON or OFF Buzzer can be heard

f.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


g.

Perform Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Precrash PCS warning light ON or OFF -

h.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


i.

Perform Active Test according to the display on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (STOP LP relay) ON or OFF Stop lights come on