Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2014.08–2015.11
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0107351 DIFFERENTIAL CASE A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41311F 1.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C303568N01
0.958,0.677 1.427,0.719 1.427,0.719 1.094,0.938 false 1.51,0.646 1.969,0.844 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing (inner race) to the front differential case.

SST
09726-36010  
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case rear tapered roller bearing (inner race) cage when installing the front differential case rear tapered roller bearing (inner race).

·

Ensure that there is no clearance between the front differential case rear tapered roller bearing (inner race) and front differential case.




b.
C196828N04
0.885,1.125 0.573,1.396 0.573,1.396 0.74,1.396 false 2.635,1.104 2.563,0.802 2.563,0.802 2.667,0.802 false 0.219,1.323 0.531,1.479 0.313,0.156 10 true SST 2.24,0.719 2.552,0.875 0.313,0.156 10 false SST

Using SST and a hammer, install a new front differential case rear tapered roller bearing (outer race) to the transaxle case sub-assembly.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case rear tapered roller bearing (outer race) and transaxle case sub-assembly.



Hide 41311E 2.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C196921N03
1.104,0.531 0.896,0.531 0.896,0.531 0.979,0.885 false 0.896,0.531 1.021,0.719 false 0.542,0.469 0.854,0.625 0.313,0.156 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing (inner race) to the front differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case front tapered roller bearing (inner race ) cage when installing the front differential case front tapered roller bearing (inner race).

·

Ensure that there is no clearance between the front differential case front tapered roller bearing (inner race) and front differential case.




b.
C196830N04
0.938,1.24 0.625,1.594 0.625,1.594 0.896,1.531 false 2.604,0.698 2.5,0.698 2.5,0.698 2.552,1.073 false 0.281,1.542 0.594,1.708 0.313,0.167 10 false SST 2.188,0.635 2.49,0.802 0.302,0.167 10 false SST

Install the shim to the transaxle housing.


c.

Using SST and a hammer, install a new front differential case front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case front tapered roller bearing (outer race), shim and transaxle housing.



Hide 3.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C288461C02
0.771,0.688 0.635,0.302 0.635,0.302 0.552,0.302 false 1.719,0.74 1.583,0.333 1.583,0.333 1.5,0.333 false 2.5,0.708 2.365,0.323 2.365,0.323 2.281,0.323 false 0.406,0.229 0.719,0.385 0.313,0.156 10 false *1 1.323,0.25 1.635,0.406 0.313,0.156 10 false *2 2.104,0.25 2.417,0.406 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer
V100135

ATF


Coat the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs with ATF.


b.
C309140C02
2.208,0.177 2.427,0.177 false 2.208,0.719 2.365,0.719 false 2.229,0.323 2.458,0.323 false 2.188,1.26 2.344,1.26 false 2.229,1.708 2.448,1.708 false 2.229,1.865 2.438,1.865 false 2.031,1.198 2.344,1.354 0.313,0.156 10 false *1 2.052,1.625 2.365,1.781 0.313,0.156 10 false *2 2.052,1.792 2.365,1.948 0.313,0.156 10 false *3 2.021,0.635 2.333,0.792 0.313,0.156 10 false *1 2.01,0.26 2.323,0.417 0.313,0.156 10 false *2 2.01,0.083 2.323,0.24 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs to the front differential case.

NOTICE:
·

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring.

·

Make sure that the conical spring is installed with the correct orientation.




c.

Install SST as shown in the illustration and tighten it.

C312293C01
4.844,0.167 5.156,0.167 false 4.469,1.24 4.969,1.24 4.969,1.24 5.125,1.146 false 4.979,1.25 5.125,1.385 false 3.135,0.188 3.448,0.344 0.313,0.156 10 false *a 1.115,2.281 1.427,2.438 0.313,0.156 10 false *b 4.552,0.083 4.865,0.24 0.313,0.156 10 false SST 4.188,1.156 4.5,1.313 0.313,0.156 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case.


HINT:
·

Tighten SST to create the necessary clearance to install the front differential pinions.

·

When installing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




d.
C287727C02
0,0 0,0 false
V100135

ATF


Coat the 2 front differential pinions and 2 front differential pinion thrust washers with ATF.


e.
C309144C01
2.729,2.823 2.573,2.823 2.573,2.823 2.573,2.365 false 2.792,2.75 3.104,2.906 0.313,0.156 10 false SST 1.969,0.698 2.281,0.854 0.313,0.156 10 false *a
*a Turn


Using SST as shown in the illustration, rotate the front differential side gear to install the 2 front differential pinions and 2 front differential pinion thrust washers.

SST
09528-52010  (09528-05030)

CAUTION:

Be careful not to catch your fingers between the front differential pinion and front differential case.


NOTICE:

Do not drop the front differential pinion or front differential pinion thrust washer.



Hide 4.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41342F 5.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C309145

Coat the front No. 1 differential pinion shaft with ATF.


b.

Install the front No. 1 differential pinion shaft to the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.


Hide 41342A 7.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C309146

Using a 5 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C309147

Using a chisel and a hammer, stake the front differential case.


Hide 8.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.


b.
C287785

Install the differential case to the transaxle case sub-assembly.


c.
C196800N01
0.875,0.74 0.573,0.208 0.573,0.208 1.333,0.469 false 0.583,0.208 1.146,0.531 false 1.771,0.5 2.979,0.281 2.979,0.281 2.292,0.74 false 2.49,1.417 3.135,1.052 3.135,1.052 2.573,0.927 false 0.677,1.625 0.219,1.292 0.219,1.292 0.594,1.021 false 0.573,0.208 1.021,0.635 false 2.021,0.615 2.948,0.292 false 1.094,1.813 1.021,2.01 false 2.604,1.156 3.104,1.052 false 1.5,1.625 2.646,2 2.646,2 2.229,1.646 false 1.896,1.656 2.615,1.979 false 0.24,1.292 0.552,1.375 false 0.24,1.281 0.542,1.198 false 1.302,1.74 1.031,2.01 1.031,2.01 0.875,1.76 false 0.406,0.104 0.563,0.302 0.156,0.198 10 false A 0.052,1.208 0.208,1.406 0.156,0.198 10 false A 0.865,1.958 1.031,2.135 0.167,0.177 10 false A 3.052,0.177 3.208,0.375 0.156,0.198 10 false A 3.188,0.969 3.344,1.167 0.156,0.198 10 false A 2.698,1.927 2.854,2.125 0.156,0.198 10 false B

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
Bolt (A) : 30.6 N*m (312 kgf*cm, 23 ft.*lbf)
Bolt (B) : 22.7 N*m (231 kgf*cm, 17 ft.*lbf)


d.
C301120N01
0.531,4.156 0.667,4.156 0.667,4.156 1.063,3.396 false 0.219,4.073 0.719,4.302 0.5,0.229 10 false SST

Using SST, turn the differential case right and left 2 or 3 times to settle the bearings.

SST
09564-33010  


e.

Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.

SST
09564-33010  

Turning Torque:

0.8 to 1.4 N*m (9 to 14 kgf*cm, 8 to 12 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness: mm (in.)
Thickness Thickness Thickness Thickness
2.000 (0.0787) 2.225 (0.0876) 2.450 (0.0965) 2.675 (0.105)
2.025 (0.0797) 2.250 (0.0886) 2.475 (0.0974) 2.700 (0.106)
2.050 (0.0807) 2.275 (0.0896) 2.500 (0.0984) 2.725 (0.107)
2.075 (0.0817) 2.300 (0.0906) 2.525 (0.0994) 2.750 (0.108)
2.100 (0.0827) 2.325 (0.0915) 2.550 (0.100) 2.775 (0.109)
2.125 (0.0837) 2.350 (0.0925) 2.575 (0.101) 2.800 (0.110)
2.150 (0.0846) 2.375 (0.0935) 2.600 (0.102) 2.825 (0.111)
2.175 (0.0856) 2.400 (0.0945) 2.625 (0.103) 2.850 (0.112)
2.200 (0.0866) 2.425 (0.0955) 2.650 (0.104) 2.875 (0.113)


f.
C296577

Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.


g.
C287785

Remove the differential case from the transaxle case assembly.


Hide 41221 9.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the front differential ring gear to more than 110°C (230°F).



b.
C313113C01
1.188,1.594 0.708,1.094 0.708,1.094 1.25,1.531 true 0.521,0.969 0.833,1.167 0.313,0.198 10 false *a
*a Matchmark


Clean the contact surface of the front differential case.


c.

Align the matchmarks, and install the front differential ring gear to the front differential case quickly.


d.
C306083

Install the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:
·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.

·

Tighten the bolts evenly in a diagonal pattern using several steps.




Hide 43420H 10.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.

Coat the lip of a new front drive shaft oil seal LH with MP grease.


b.
C307977N02
1.417,1.292 0.677,2.302 0.677,2.302 1.385,1.521 true 0.365,2.25 0.719,2.448 0.354,0.198 10 false SST

Using SST and a hammer, install the front drive shaft oil seal LH.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal LH is installed in the correct direction.

·

Do not damage the front drive shaft oil seal LH lip.




Hide 43410M 11.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

for Inside:

i.

Coat the lip of a new front drive shaft oil seal RH with MP grease.


ii.
C301121N02
2.531,0.635 2.802,0.5 2.802,0.5 2.604,1 false 2.844,0.385 3.26,0.615 0.417,0.229 10 false SST

Using SST and a hammer, install the front drive shaft oil seal RH to the front differential case.

SST
09950-60010  (09951-00410)
09950-70010  (09951-07200)

Standard Depth:

21.5 to 22.5 mm (0.846 to 0.886 in.)


NOTICE:

Do not damage the front drive shaft oil seal RH lip.




b.

for Outside:

i.

Coat the lip of a new front drive shaft oil seal RH with MP grease.


ii.
C188861E03
1.198,1.906 1.125,2.333 1.125,2.333 0.906,2.104 false 1.042,2.375 1.396,2.563 0.354,0.188 10 false SST

Using SST and a hammer, install the front drive shaft oil seal RH to the transaxle housing.

SST
09649-17010  
09950-70010  (09951-07200)

Standard Depth:

5.5 to 6.5 mm (0.217 to 0.256 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal RH is installed in the correct direction.

·

Do not damage the front drive shaft oil seal RH lip.