Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › CYLINDER HEAD › 2014.08–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109584 CYLINDER HEAD G

2GR-FE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.

Using a precision straightedge and feeler gauge, measure the warpage of the surfaces which contact the cylinder block sub-assembly and manifolds.

A283828C03
3.948,0.229 4.646,0.781 0.698,0.552 12 false *A 0.719,2.354 1.271,2.708 0.552,0.354 12 false *B 3.958,2.333 4.427,2.646 0.469,0.313 12 false *C
*A Bottom Side *B Intake Manifold Side
*C Exhaust Manifold Side - -


Standard Warpage:
Item Specified Condition
Bottom Side 0.05 mm (0.00197 in.)
Intake Manifold Side 0.08 mm (0.00315 in.)
Exhaust Manifold Side 0.08 mm (0.00315 in.)


Maximum Warpage:
Item Specified Condition
Bottom Side 0.10 mm (0.00394 in.)
Intake Manifold Side 0.10 mm (0.00394 in.)
Exhaust Manifold Side 0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the cylinder head sub-assembly.


Hide 2.INSPECT CYLINDER HEAD FOR CRACKS

a.
A120706

Using a dye penetrant, check the intake ports, exhaust ports and bottom surface of the cylinder head sub-assembly for cracks.

If cracks are found, replace the cylinder head sub-assembly.


Hide 13711 3.INSPECT INTAKE VALVE

a.
A121378

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.470 to 5.485 mm (0.2154 to 0.2159 in.)


If the diameter is not as specified, check the oil clearance.


b.
A121379C12
0.524,1.296 0.677,1.479 0.153,0.183 10 *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)


Minimum Margin Thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the intake valve.


c.
A121380C25
1.884,1.028 2.055,1.173 0.17,0.145 10 *a
*a Overall Length


Using a vernier caliper, measure the valve overall length.

Standard Overall Length:

105.85 mm (4.1673 in.)


Minimum Overall Length:

105.35 mm (4.1476 in.)


If the overall length is less than the minimum, replace the intake valve.


Hide 13715 4.INSPECT EXHAUST VALVE

a.
A124001

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.465 to 5.480 mm (0.2152 to 0.2157 in.)


If the diameter is not as specified, check the oil clearance.


b.
A121382C28
0.613,1.323 0.769,1.492 0.156,0.169 10 *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)


Minimum Margin Thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the exhaust valve.


c.
A121383C20
1.932,0.968 2.107,1.134 0.175,0.166 10 *a
*a Overall Length


Using a vernier caliper, measure the valve overall length.

Standard Overall Length:

110.40 mm (4.3464 in.)


Minimum Overall Length:

109.90 mm (4.3268 in.)


If the overall length is less than the minimum, replace the exhaust valve.


Hide 11131 5.INSPECT INTAKE VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the intake valve seat.


c.
A314816C01
1.479,1.146 1.792,1.344 0.313,0.198 10 false *a
*a Width


Check the valve face and intake valve seat by using the following procedure:

i.

If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the intake valve.


ii.

If Prussian blue appears around the entire intake valve seat, the intake valve seat and valve face are concentric. If not, resurface the intake valve seat.


iii.

Check that the intake valve seat contacts the middle of the valve face with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).



Hide 11135 6.INSPECT EXHAUST VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the exhaust valve seat.


c.
A314816C01
1.479,1.146 1.792,1.344 0.313,0.198 10 false *a
*a Width


Check the valve face and exhaust valve seat by using the following procedure:

i.

If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the exhaust valve.


ii.

If Prussian blue appears around the entire exhaust valve seat, the exhaust valve seat and valve face are concentric. If not, resurface the exhaust valve seat.


iii.

Check that the exhaust valve seat contacts the middle of the valve face with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).



Hide 13711B 7.INSPECT INNER COMPRESSION SPRING

a.
A314490

Using a vernier caliper, measure the free length of the inner compression spring.

Standard Free Length:

50.55 mm (1.9902 in.)


If the free length is not as specified, replace the inner compression spring.


b.
A319225C07
1.281,0.813 1.594,0.813 false 1.083,0.74 1.396,0.896 0.313,0.156 10 false *1 0.073,1.25 1.125,1.448 1.052,0.198 10 false 50 mm (1.97 in.)
*a Deviation


Using a steel square, measure the deviation of the inner compression spring.

Maximum Deviation:

1.75 mm (0.0689 in.)


Maximum Angle (reference):

2°


If the deviation is more than the maximum, replace the inner compression spring.


Hide 8.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A120707

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard Valve Guide Bush Inside Diameter:

5.510 to 5.530 mm (0.2169 to 0.2177 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.08 mm (0.00315 in.)
Exhaust 0.10 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the valve and valve guide bush.