Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2015.11–2016.11
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0107347 AUTOMATIC TRANSAXLE UNIT A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 35104V 1.REMOVE BREATHER PLUG HOSE

a.
C190663

Using a screwdriver, remove the breather plug hose from the transaxle case sub-assembly.


b.
C134952C07
2.938,2.396 2.938,2.677 false 2.021,2.479 2.458,2.479 false 1.656,1.719 2.01,1.719 false 0.646,0.865 0.802,0.594 0.802,0.594 0.938,0.594 false 1.479,1.646 1.76,1.938 0.281,0.292 10 false *2 0.99,0.531 1.375,0.813 0.385,0.281 10 false *1 1.823,2.396 1.979,2.552 0.156,0.156 10 false *3 2.875,2.698 3.135,2.927 0.26,0.229 10 false *4
*1 No. 1 Breather Plug (ATM)
*2 Breather Plug Hose
*3 No. 2 Breather Plug (ATM)
*4 O-ring


Using a screwdriver, remove the No. 1 breather plug (ATM) and No. 2 breather plug (ATM) from the breather plug hose.


c.

Using a screwdriver, remove the O-ring from the No. 2 breather plug (ATM).


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C136685

Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft sub-assembly.


b.
C136686

Remove the 2 bolts and park/neutral position switch assembly from the transaxle case sub-assembly.

NOTICE:

Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the park/neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



Hide 3.REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)

a.
C289626

Remove the oil cooler tube union (outlet oil cooler union) from the transaxle case sub-assembly.


b.

Remove the O-ring from the oil cooler tube union (outlet oil cooler union).


Hide 32921X 4.REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION)

a.
C289627

Remove the oil cooler tube union (inlet oil cooler union) from the transaxle case sub-assembly.


b.

Remove the O-ring from the oil cooler tube union (inlet oil cooler union).


Hide 35104Q 5.REMOVE NO. 1 TRANSAXLE CASE PLUG

a.
C134958

Remove the 3 No. 1 transaxle case plugs from the transaxle case sub-assembly.


b.

Using a screwdriver, remove the 3 O-rings from the 3 No. 1 transaxle case plugs.


Hide 35104R 6.REMOVE NO. 2 TRANSAXLE CASE PLUG

a.
C134959

Using a 6 mm hexagon socket wrench, remove the 3 No. 2 transaxle case plugs from the transaxle housing.


b.

Remove the gasket from each of the 3 No. 2 transaxle case plugs.


Hide 30500 7.SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY

a.
C136444

Support the automatic transaxle assembly with wooden blocks.


Hide 35106D 8.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C134961

Using a 6 mm hexagon socket wrench, remove the overflow plug from the automatic transaxle oil pan sub-assembly.


b.

Remove the gasket from the overflow plug.


c.
C141531

Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.


d.
C274804

Remove the 18 bolts, automatic transaxle oil pan sub-assembly and automatic transaxle oil pan gasket from the transaxle case sub-assembly.


e.
C134963C07
2.677,0.219 1.885,0.219 1.885,0.219 1.885,1.417 false 2.448,1 2.448,0.219 false 2.74,0.135 2.917,0.302 0.177,0.167 10 false *1
*1 Transmission Oil Cleaner Magnet


Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


Hide 35394 9.INSPECT TRANSMISSION OIL CLEANER MAGNET

Hide 35330 10.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C136687

Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.


b.
C136688C05
1.823,0.375 2.063,0.375 false 2.104,0.333 2.479,0.594 0.375,0.26 10 false *1
*1 O-ring


Remove the O-ring from the valve body oil strainer assembly.


Hide 35410 11.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C136689

Remove the 11 bolts and transmission valve body assembly from the transaxle case sub-assembly.

NOTICE:

When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.



Hide 35145C 12.REMOVE TRANSAXLE CASE GASKET

a.
C287964

Remove the 2 transaxle case gaskets from the transaxle case sub-assembly.


Hide 35102 14.REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C136430

Remove the refill plug from the rear transaxle cover sub-assembly.


b.

Remove the gasket from the refill plug.


c.
C288350

Remove the 3 No. 1 automatic transaxle case plugs from the rear transaxle cover sub-assembly.


d.

Using a screwdriver, remove the 3 O-rings from the 3 No. 1 automatic transaxle case plugs.


e.
C291004

Remove the 14 bolts from the rear transaxle cover sub-assembly.


f.

Using a brass bar and a hammer, tap on the circumference of the rear transaxle cover sub-assembly to remove the rear transaxle cover sub-assembly from the transaxle case sub-assembly.


g.
C287966

Using a screwdriver, remove the 3 O-rings from the transaxle case sub-assembly.

HINT:

Tape the screwdriver tip before use.



h.
C297890C03
1.063,1.292 0.74,0.521 0.74,0.521 0.604,0.521 false 0.729,1.542 0.542,1.115 0.542,1.115 0.406,1.115 false 0.438,0.448 0.771,0.719 0.333,0.271 10 false *1 0.219,1.042 0.5,1.406 0.281,0.365 10 false *2
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


Remove the thrust needle roller bearing and thrust needle roller race from the rear transaxle cover sub-assembly.


i.
C299131C01
1.365,0.5 1.469,0.5 1.469,0.5 1.719,0.823 true 1.958,1.302 2.219,1.823 2.219,1.823 2.083,1.823 true 1.188,0.417 1.51,0.688 0.323,0.271 10 false *1 1.906,1.75 2.229,2.021 0.323,0.271 10 false *1
*1 Oil Seal Ring


Using a screwdriver, remove the 2 oil seal rings from the rear transaxle cover sub-assembly.

HINT:

Tape the screwdriver tip before use.



j.
C287967

Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and rear transaxle cover plate from the rear transaxle cover sub-assembly.


k.
C194888C07
1.417,0.896 1.521,0.896 false 1.146,0.833 1.458,1.01 0.313,0.177 10 true SST 3.156,0.375 3.333,0.552 0.177,0.177 10 false *a 0.354,0.833 0.531,1.01 0.177,0.177 10 false *b
*a Turn
*b Hold


Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.

SST
09319-60020  


Hide 35635C 15.REMOVE DIRECT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C136442C02
0.875,1.323 0.875,2.104 false 2.76,0.167 3.042,0.167 3.042,0.167 2.573,1.417 false 0.802,2.135 1.229,2.375 0.427,0.24 10 false *1 2.552,0.104 2.844,0.344 0.292,0.24 10 false *2
*1 Direct Multiple Disc Clutch Assembly
*2 Thrust Needle Roller Bearing


Remove the direct multiple disc clutch assembly from the transaxle case sub-assembly.


b.

Remove the thrust needle roller bearing from the direct multiple disc clutch assembly.


c.
C296565C01
1.135,0.167 1.646,0.167 false 1.792,1.979 2.302,1.979 false 2.344,1.896 2.656,2.052 0.313,0.156 10 false *1 0.938,0.104 1.25,0.26 0.313,0.156 10 false *2
*1 Intermediate Shaft Oil Seal
*2 O-ring


Using a screwdriver, remove the intermediate shaft oil seal from the direct multiple disc clutch assembly.

HINT:

Tape the screwdriver tip before use.



d.

Using a screwdriver, remove the O-ring from the direct multiple disc clutch assembly.

HINT:

Tape the screwdriver tip before use.



Hide 35730 16.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

a.
C293949C01
2.657,0.118 2.849,0.299 0.192,0.181 10 *1 2.622,0.215 2.52,0.215 2.52,0.215 2.096,0.56 false
*1 Snap Ring


Using 2 screwdrivers and a hammer, remove the snap ring from the direct multiple disc clutch assembly.


b.
C293946

Remove the rear planetary sun gear assembly from the direct multiple disc clutch assembly.


c.
C201526C09
2.104,0.875 2.219,0.99 2.219,0.99 2.219,1.313 false 1.375,0.104 1.719,0.104 1.719,0.104 1.885,0.198 false 1.198,0.021 1.375,0.177 0.177,0.156 10 false *1 2.125,1.313 2.302,1.49 0.177,0.177 10 false *2
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


Remove the thrust needle roller bearing and thrust needle roller race from the direct multiple disc clutch assembly.


Hide 35730 17.INSPECT REAR PLANETARY SUN GEAR ASSEMBLY

Hide 35111C 18.REMOVE TRANSAXLE HOUSING

a.
C296577

Remove the 20 bolts from the transaxle housing.


b.

Using a brass bar and a hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case sub-assembly.


Hide 19.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE

a.
C194889N02
1.193,1.543 1.512,1.712 0.319,0.169 10 SST 0.942,1.629 1.152,1.629 false

Using SST, remove the counter driven gear front tapered roller bearing outer race and shim from the transaxle housing.

SST
09308-00010  


Hide 35882A 20.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C287969

Remove the bolt, clamp and differential gear lube apply tube from the transaxle housing.


Hide 35035 21.REMOVE FRONT OIL PUMP ASSEMBLY

a.
C296578C01
2.344,0.188 2.729,0.188 false 2.771,0.094 3.083,0.292 0.313,0.198 10 false *1
*1 Gasket


Remove the 7 bolts and front oil pump assembly from the transaxle case sub-assembly.


b.

Remove the gasket from the front oil pump assembly.


c.
C293908C02
0.375,2.76 0.625,2.76 false 0.167,2.677 0.479,2.833 0.313,0.156 10 false *1
*1 Thrust Needle Roller Race


Remove the thrust needle roller race from the underdrive planetary gear assembly.


d.
C293909C01
2.135,1.25 2.521,1.25 false 0.969,0.542 1.354,0.542 false 0.771,0.438 1.083,0.635 0.313,0.198 10 false *1 2.563,1.146 2.875,1.344 0.313,0.198 10 false *2
*1 Thrust Needle Roller Bearing
*2 O-ring


Remove the thrust needle roller bearing from the counter drive gear nut.


e.

Remove the O-ring from the transaxle case sub-assembly.


Hide 35301B 22.REMOVE FRONT OIL PUMP BODY O-RING

a.
C293910

Remove the front oil pump body O-ring from the front oil pump body assembly.


Hide 35683B 23.REMOVE NO. 3 BRAKE DISC

a.
C136451C03
1.135,0.737 0.97,0.484 0.97,0.484 0.67,0.484 false 0.463,0.409 0.633,0.565 0.17,0.156 10 *1
*1 Snap Ring


Using a screwdriver, remove the snap ring from the front oil pump assembly.


b.
C136452C08
1.99,0.281 2.24,0.281 false 2.146,1.25 2.292,1.25 false 2.156,0.719 2.229,0.719 2.229,0.719 2.229,1.635 false 2.229,1.635 2.156,1.635 false 1.177,1.99 1.323,1.99 false 1.302,0.938 1.115,0.938 false 1.302,1.438 1.219,1.438 1.219,1.438 1.219,0.938 false 2.302,0.198 2.677,0.5 0.375,0.302 10 false *1 2.354,1.156 2.521,1.333 0.167,0.177 10 false *3 0.917,0.854 1.094,1.031 0.177,0.177 10 false *2 0.948,1.896 1.115,2.083 0.167,0.188 10 false *1
*1 No. 3 Brake Flange
*2 No. 3 Brake Plate
*3 No. 3 Brake Disc


Remove the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates from the front oil pump assembly.


Hide 34330 25.REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C136458

Remove the underdrive planetary gear assembly from the front oil pump assembly.


Hide 35663 26.REMOVE NO. 3 BRAKE HUB

a.
C136454

Remove the No. 3 brake hub from the underdrive planetary gear assembly.


b.
C202906C01
1.146,0.208 1.271,0.208 1.271,0.208 1.469,0.344 false 1.188,1.115 1.271,1.115 1.271,1.115 1.469,0.948 false 1.01,0.125 1.188,0.292 0.177,0.167 10 false *1 1.031,1.052 1.271,1.365 0.24,0.313 10 false *2
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing


Remove the thrust needle roller bearing and thrust needle roller race from the underdrive planetary gear assembly.


Hide 35706V 27.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C290582C01
0.396,2.198 0.906,2.198 false 2,0.5 2.51,0.5 false 1.958,3.021 2.469,3.021 false 2.594,0.427 3,0.781 0.406,0.354 10 false *1 0.219,2.125 0.667,2.531 0.448,0.406 10 false *2 2.542,2.938 2.979,3.302 0.438,0.365 10 false *3
*1 Planetary Sun Gear Sub-assembly
*2 Underdrive Planetary Gear Assembly
*3 Snap Ring


While expanding the snap ring with snap ring pliers, remove the planetary sun gear sub-assembly from the underdrive planetary gear assembly.


b.

Remove the snap ring from the underdrive planetary gear assembly.


Hide 34330 28.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY

Hide 35706V 29.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

Hide 35701 30.REMOVE INPUT SHAFT SUB-ASSEMBLY

a.
C136459

Remove the input shaft sub-assembly from the front oil pump assembly.


b.
C136460C02
1.417,0.208 1.177,0.208 false 2.177,0.708 1.927,0.708 false 1.833,2.729 2.417,2.542 2.417,2.542 1.844,3.052 false 1.844,2.896 2.417,2.542 false 0.979,1.844 1.51,1.844 false 2.208,0.615 2.375,0.771 0.167,0.156 10 false *2 0.969,0.125 1.125,0.281 0.156,0.156 10 false *1 0.771,1.76 0.927,1.906 0.156,0.146 10 false *4 2.469,2.458 2.625,2.615 0.156,0.156 10 false *3
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing
*3 Input Shaft Oil Seal Ring
*4 Input Shaft Sub-assembly


Remove the thrust needle roller bearing and thrust needle roller race from the input shaft sub-assembly.


c.

Using a screwdriver, remove the 3 input shaft oil seal rings from the input shaft sub-assembly.

HINT:

Tape the screwdriver tip before use.



Hide 34321 31.REMOVE UNDERDRIVE PLANETARY SUN GEAR

a.
C136461C02
1.01,0.604 1.385,0.604 false 2.292,1.229 2,1.229 false 2.354,1.135 2.521,1.302 0.167,0.167 10 false *2 0.792,0.531 0.948,0.677 0.156,0.146 10 false *1
*1 Underdrive Planetary Sun Gear
*2 Thrust Needle Roller Bearing


Remove the underdrive planetary sun gear from the front oil pump assembly.


b.

Remove the thrust needle roller bearing from the front oil pump assembly.


Hide 32.REMOVE NO. 1 BRAKE DISC

a.
C153477C05
2.198,0.573 2.49,0.573 false 2.198,1.167 2.333,1.167 2.333,1.167 2.333,0.573 false 1.24,0.885 1.042,0.885 false 2.51,0.49 2.677,0.646 0.167,0.156 10 false *1 0.844,0.813 1.177,1.135 0.333,0.323 10 false *2
*1 Snap Ring
*2 Brake Snap Ring Stopper


Using a screwdriver, remove the 2 snap rings and brake snap ring stopper from the front oil pump assembly.


b.
C136463C02
1.781,0.49 2.094,0.49 false 1.76,1.208 2.031,1.208 false 1.927,1.208 1.927,2.521 1.927,2.521 2.021,2.521 false 2.031,1.646 1.927,1.646 false 2.042,2.115 1.927,2.115 false 2.865,0.906 2.917,0.906 2.917,0.906 2.917,2.271 false 2.927,2.271 2.865,2.271 false 2.917,1.854 2.865,1.854 false 2.865,1.344 2.969,1.344 false 1.573,0.396 1.875,0.698 0.302,0.302 10 false *1 3.042,1.292 3.302,1.49 0.26,0.198 10 false *3 1.521,1.125 1.896,1.417 0.375,0.292 10 false *2
*1 No. 1 Brake Flange
*2 No. 1 Brake Plate
*3 No. 1 Brake Disc


Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the front oil pump assembly.


Hide 35608L 34.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C136464

Remove the 3 2nd brake piston return spring sub-assemblies from the front oil pump assembly.


Hide 35608L 35.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35621F 36.REMOVE NO. 1 BRAKE PISTON

a.
C136465

While holding the front oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the front oil pump assembly to remove the No. 1 brake piston.


b.
C136466C03
1.99,0.667 2.385,0.667 false 1.354,0.667 0.906,0.667 false 2.417,0.573 2.563,0.729 0.146,0.156 10 false *1 0.698,0.594 1.125,0.906 0.427,0.313 10 false *1
*1 O-ring


Using a screwdriver, remove the 2 O-rings from the No. 1 brake piston.

HINT:

Tape the screwdriver tip before use.



Hide 41311 37.REMOVE FRONT DIFFERENTIAL CASE

a.
C196803

Remove the front differential case from the transaxle case sub-assembly.


Hide 35782H 38.REMOVE COUNTER DRIVE GEAR NUT

a.
C136698N03
1.583,0.698 1.198,0.438 false 0.865,0.344 1.344,0.646 0.479,0.302 10 false SST

Using SST and a hammer, release the staked part of the planetary gear assembly.

SST
09930-00010  


b.
C299132N01
1.542,4.042 1.969,4.427 0.427,0.385 10 false P

Turn the manual valve lever shaft sub-assembly 2 notches counterclockwise to set it to the P position as shown in the illustration.


c.
C136468N03
0.363,0.201 0.682,0.37 0.319,0.169 10 SST 1.655,1.408 0.737,0.282 false

Using SST, remove the counter drive gear nut from the front planetary gear assembly.

SST
09387-00130  


Hide 35783R 39.REMOVE COUNTER DRIVEN GEAR

a.
C299133N01
1.542,4.031 1.729,4.271 0.188,0.24 10 false N

Turn the manual valve lever shaft sub-assembly 2 notches clockwise to set it to the N position as shown in the illustration.


b.
C136469

Remove the counter driven gear from the transaxle case sub-assembly.


Hide 40.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING

a.
C194890C02
1.645,0.0030 1.815,0.191 0.17,0.189 10 *a 0.068,0.69 0.238,0.878 0.17,0.189 10 *b 1.611,0.66 1.919,0.828 0.309,0.168 10 SST 1.44,0.592 1.587,0.739 1.587,0.739 1.438,1.214 false 1.587,0.739 1.063,1.174 false 2.903,0.114 3.212,0.281 0.309,0.168 10 SST 2.233,0.493 2.883,0.221 2.883,0.221 2.778,0.673 false
*a Turn
*b Hold


Using SST, remove the counter driven gear front tapered roller bearing from the counter driven gear.

SST
09950-00020  
09950-00030  
09950-60010  (09951-00400)


Hide 41.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING

a.
C194891C02
0.552,0.688 0.24,1.521 0.24,1.521 0.917,1.375 false 2.281,1.26 2.063,1.573 false 2.896,0.354 2.823,0.354 2.823,0.354 2.698,1.094 false 1.615,0 1.781,0.177 0.167,0.177 10 false *a 0.042,0.604 0.26,0.792 0.219,0.188 10 false *b 0.052,1.563 0.375,1.729 0.323,0.167 10 false SST 2.906,0.26 3.229,0.427 0.323,0.167 10 false SST 1.885,1.594 2.208,1.76 0.323,0.167 10 false SST
*a Turn
*b Hold


Using SST, remove the counter driven gear rear tapered roller bearing from the counter driven gear.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)
09950-60010  (09951-00320)


Hide 35558 42.REMOVE PAWL SHAFT CLAMP

a.
C136472

Remove the bolt and pawl shaft clamp from the transaxle case sub-assembly.


Hide 35596 43.REMOVE PAWL STOPPER PLATE

a.
C136473

Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.


Hide 35598 44.REMOVE PARKING LOCK SLEEVE

a.
C136474

Remove the parking lock sleeve from the transaxle case sub-assembly.


Hide 35557 45.REMOVE PARKING LOCK PAWL

a.
C136475C04
1.542,0.313 1.333,0.313 1.333,0.313 1.156,1.292 false 0.885,0.271 0.698,0.271 0.698,0.271 0.458,1.615 false 0.458,2.802 0.458,2.625 0.458,2.625 1.052,2.458 false 1.531,2.698 0.771,3.021 0.771,3.021 0.771,3.167 false 0.365,2.844 0.542,3.021 0.177,0.177 10 false *3 0.698,3.208 1.063,3.375 0.365,0.167 10 false *4 0.948,0.188 1.115,0.354 0.167,0.167 10 false *1 1.646,0.229 1.969,0.427 0.323,0.198 10 true *2
*1 Parking Lock Pawl Shaft
*2 Parking Lock Pawl
*3 Spring
*4 Parking Lock Pawl Pin


Remove the spring, parking lock pawl pin, parking lock pawl shaft and parking lock pawl from the transaxle case sub-assembly.


Hide 46.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE

a.
C194892N02
0.615,0.583 0.833,0.583 false 0.24,0.5 0.563,0.667 0.323,0.167 10 false SST

Using SST, remove the counter driven gear rear tapered roller bearing outer race from the transaxle case sub-assembly.

SST
09308-00010  


Hide 35790 47.REMOVE ONE-WAY CLUTCH ASSEMBLY

a.
C141525

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C141526C06
1.771,1.01 2.313,1.01 false 0.833,0.313 1.281,0.313 false 2.375,0.938 2.792,1.167 0.417,0.229 10 false *2 0.615,0.229 0.99,0.521 0.375,0.292 10 false *1
*1 One-way Clutch Assembly with Planetary Ring Gear
*2 Thrust Needle Roller Bearing


Remove the one-way clutch assembly with planetary ring gear from the transaxle case sub-assembly.


c.

Remove the thrust needle roller bearing from the front planetary gear assembly.


Hide 35743K 49.REMOVE PLANETARY RING GEAR

a.
C201345C07
0.917,0.094 1.01,0.094 1.01,0.094 1.313,0.375 false 1.135,1.417 1.396,1.417 false 2.521,0.979 2.802,1.052 2.802,1.052 2.802,1.135 false 0.74,0.031 0.896,0.219 0.156,0.188 10 false *1 0.969,1.344 1.135,1.521 0.167,0.177 10 false *3 2.698,1.146 2.885,1.344 0.188,0.198 10 false *2
*1 One-way Clutch Assembly
*2 Outer Race Retainer
*3 Planetary Ring Gear


Remove the planetary ring gear from the one-way clutch assembly.


b.

Remove the outer race retainer from the one-way clutch assembly.


Hide 35762E 50.REMOVE PLANETARY RING GEAR FLANGE

a.
C136480C08
1.271,0.646 0.969,0.646 false 0.958,2.302 1.219,2.302 false 2.083,1.313 2.396,1.313 false 0.719,2.229 0.896,2.396 0.177,0.167 10 false *3 2.458,1.24 2.802,1.458 0.344,0.219 10 false *2 0.719,0.573 0.896,0.74 0.177,0.167 10 false *1
*1 Snap Ring
*2 Planetary Ring Gear Flange
*3 Planetary Ring Gear


Using a screwdriver, remove the snap ring from the planetary ring gear.


b.

Remove the planetary ring gear flange from the planetary ring gear.


Hide 35682A 51.REMOVE NO. 2 BRAKE DISC

a.
C141524

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C136483C03
2.502,1.086 2.668,1.266 0.166,0.18 10 *3 0.891,1.185 1.051,1.365 0.16,0.18 10 *2 2.357,0.435 2.521,0.615 0.164,0.18 10 *1 1.31,0.87 1.213,0.87 1.213,0.87 1.213,1.702 false 1.213,1.702 1.31,1.702 false 1.31,1.069 1.213,1.069 false 1.32,1.475 1.213,1.475 false 1.31,1.268 1.105,1.268 false 2.166,0.542 2.305,0.542 false 2.213,0.781 2.364,0.781 2.364,0.781 2.364,1.598 false 2.364,1.598 2.206,1.598 false 2.213,0.985 2.364,0.985 false 2.212,1.403 2.364,1.403 false 2.213,1.184 2.451,1.184 false
*1 No. 2 Brake Flange
*2 No. 2 Brake Plate
*3 No. 2 Brake Disc


Remove the No. 2 brake flange, 5 No. 2 brake discs and 5 No. 2 brake plates from the transaxle case sub-assembly.


Hide 35068C 53.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C136482

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C136484

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case sub-assembly.


Hide 35068C 54.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 35622G 55.REMOVE NO. 2 BRAKE PISTON

a.
C136485

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the ATF hole to remove the No. 2 brake piston from the transaxle case sub-assembly.


b.
C136673C03
1.979,0.5 2.563,0.5 false 1.375,1.208 0.917,1.208 false 0.688,1.115 0.844,1.302 0.156,0.188 10 false *1 2.646,0.448 3.073,0.75 0.427,0.302 10 false *1
*1 O-ring


Using a screwdriver, remove the 2 O-rings from the No. 2 brake piston.

HINT:

Tape the screwdriver tip before use.



Hide 35720 56.REMOVE FRONT PLANETARY GEAR ASSEMBLY

a.
C136674N08
1.781,1.75 2.573,1.333 2.573,1.333 1.885,1.927 false 2.625,1.24 2.969,1.406 0.344,0.167 10 false SST

Using SST and a press, remove the front planetary gear assembly from the transaxle case sub-assembly.

SST
09950-60010  (09951-00580)
09950-70010  (09951-07100)


Hide 35720 57.INSPECT FRONT PLANETARY GEAR ASSEMBLY

Hide 35782C 58.REMOVE COUNTER DRIVE GEAR

NOTICE:

Perform this procedure only when the counter drive gear bearing or transaxle case sub-assembly is replaced.


a.
C274813N01
1.302,1.323 0.677,0.531 0.677,0.531 1.406,1.177 false 0.927,3.042 1.219,3.042 1.219,3.042 1.021,3.24 false 0.406,0.396 0.865,0.594 0.458,0.198 10 SST 1.271,2.948 1.729,3.146 0.458,0.198 10 SST

Using SST and a press, remove the counter drive gear and bearing inner race (rear side) from the transaxle case sub-assembly.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)


b.
C295183

As shown in the illustration, tighten 3 service bolts evenly to make a clearance of approximately 20.0 mm (0.787 in.) between the counter drive gear and bearing inner race (front side).


c.
C194894C03
0.5,1.49 0.417,1.646 0.417,1.646 0.906,1.469 false 2.344,0.802 2.438,0.802 2.438,0.802 2.26,1.229 false 2.885,0.833 2.781,1.146 false 1.635,0.021 1.802,0.177 0.167,0.156 10 false *a 0.042,0.604 0.219,0.792 0.177,0.188 10 false *b 0.094,1.625 0.656,1.906 0.563,0.281 10 false SST 2.917,0.75 3.427,1.052 0.51,0.302 10 false SST 2,0.729 2.458,0.958 0.458,0.229 10 false SST
*a Turn
*b Hold


Using SST, remove the bearing inner race (front side) from the counter drive gear.

SST
09950-00020  
09950-00030  
09950-60020  (09951-00710)


Hide 35623 59.REMOVE NO. 3 BRAKE PISTON

a.
C136678

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C136679C02
0.816,0.427 0.975,0.582 0.159,0.155 10 *2 1.008,0.509 1.114,0.509 1.114,0.509 1.459,0.888 false 2.309,0.229 2.463,0.381 0.154,0.152 10 *1 2.281,0.311 2.031,0.311 false
*1 Brake Piston Return Spring
*2 No. 3 Brake Piston


Remove the brake piston return spring from the transaxle case sub-assembly.


c.

Remove the No. 3 brake piston from the transaxle case sub-assembly.


Hide 35409 60.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C201354

Remove the bolt, cover and manual detent spring sub-assembly from the transaxle case sub-assembly.


Hide 35501 61.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

a.
C289567

Remove the parking lock rod sub-assembly from the manual valve lever shaft sub-assembly.

HINT:

Align the protrusions with the notches on the manual valve lever shaft sub-assembly to remove the parking lock rod sub-assembly.



Hide 35506 62.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C201356

Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the manual valve lever shaft sub-assembly.


b.
C288352

Remove the manual valve lever shaft sub-assembly from the transaxle case sub-assembly.


Hide 35506F 63.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C299161

Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case sub-assembly.

HINT:

Tape the screwdriver tip before use.