Home › Vehicle Exterior › WIPER / WASHER › RAIN SENSOR › from 2015.11
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0101308 RAIN SENSOR G

WIPER / WASHER  RAIN SENSOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89941 1.INSPECT RAIN SENSOR (for LHD)

a.
E267170C08
1.479,0.344 1.885,0.615 0.406,0.271 1.948,1.354 2.448,1.656 false 1.583,1.354 1.073,1.688 false 0.135,0.156 0.448,0.354 0.313,0.198 10 false *a 0.948,1.719 1.26,1.917 0.313,0.198 10 false ES 2.396,1.677 2.76,1.875 0.365,0.198 10 false SIG 1.573,0.385 2.031,0.583 0.458,0.198 10 false S13
*a Front view of wire harness connector
(to Rain Sensor)


Disconnect the S13 rain sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S13-4 (SIG) - S13-2 (ES) Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S13-2 (ES) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.


d.
E257042C05
0.087,0.071 0.320,0.259 0.232,0.188 10 *a 1.126,0.265 1.586,0.417 0.460,0.152 10 ES 2.294,0.265 2.808,0.417 0.513,0.152 10 MPX 1.821,0.97 1.314,0.448 false 1.97,0.97 2.476,0.448 false
*a Component with harness connected
(Rain Sensor)


Reconnect the S13 rain sensor connector.


e.

Connect an oscilloscope to the rain sensor connector.


f.

Check for pulses.

OK:
Tester Connection Condition Specified Condition
1 (MPX) - 2 (ES) Ignition switch ON Pulse generation


If the result is not as specified, replace the rain sensor.


Hide 89941 2.INSPECT RAIN SENSOR (for RHD)

a.
E267170C25
1.479,0.344 1.885,0.615 0.406,0.271 1.948,1.354 2.448,1.656 false 1.583,1.354 1.073,1.688 false 0.135,0.156 0.448,0.354 0.313,0.198 10 false *a 0.948,1.719 1.26,1.917 0.313,0.198 10 false ES 2.396,1.677 2.76,1.875 0.365,0.198 10 false SIG 1.573,0.385 2.031,0.583 0.458,0.198 10 false S14
*a Front view of wire harness connector
(to Rain Sensor)


Disconnect the S14 rain sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S14-4 (SIG) - S14-2 (ES) Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S14-2 (ES) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.


d.
E257042C05
0.087,0.071 0.320,0.259 0.232,0.188 10 *a 1.126,0.265 1.586,0.417 0.460,0.152 10 ES 2.294,0.265 2.808,0.417 0.513,0.152 10 MPX 1.821,0.97 1.314,0.448 false 1.97,0.97 2.476,0.448 false
*a Component with harness connected
(Rain Sensor)


Reconnect the S14 rain sensor connector.


e.

Connect an oscilloscope to the rain sensor connector.


f.

Check for pulses.

OK:
Tester Connection Condition Specified Condition
1 (MPX) - 2 (ES) Ignition switch ON Pulse generation


If the result is not as specified, replace the rain sensor.