Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0109809 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0717  Input Speed Sensor Circuit No Signal  P07BF  Input/Turbine Speed Sensor "A" Circuit Low  P07C0  Input/Turbine Speed Sensor "A" Circuit High  


DESCRIPTION

This sensor detects the rotation speed of the turbine, which indicates the input shaft revolution (speed) of the transaxle. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (NC), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.

C133216C01
3.146,1.729 2.458,0.542 2.458,0.542 2.24,0.542 false 4.083,1.688 4.458,0.51 4.458,0.51 4.594,0.51 false 3.688,2.698 4,3.271 4,3.271 4.125,3.271 false 3.104,2.49 2.75,3.323 2.75,3.323 2.646,3.323 false 2.052,0.469 2.302,0.646 0.25,0.177 10 *1 4.625,0.427 4.781,0.594 0.156,0.167 10 *2 2.479,3.26 2.646,3.406 0.167,0.146 10 *3 4.156,3.208 4.333,3.354 0.177,0.146 10 *4
*1 Counter Gear *2 Clutch Drum
*3 Output Speed Sensor NC *4 Input Speed Sensor NT


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0717 Input Speed Sensor Circuit No Signal ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more: (1-trip detection logic)
(a) Vehicle speed: 50 km/h (31 mph) or more
(b) Park/neutral position switch (R) is OFF
(c) Speed sensor (NT): less than 300 rpm
·

Transmission revolution sensor (speed sensor NT)

·

Transmission wire

·

Wiring harness connector

·

ECM


Comes on DTC stored
P07BF Input/Turbine Speed Sensor "A" Circuit Low When the speed sensor input voltage is less than 0.2 V for 4.5 seconds or more. (1-trip detection logic)
·

Transmission revolution sensor (speed sensor NT)

·

Transmission wire

·

Wiring harness connector

·

ECM


Comes on DTC stored
P07C0 Input/Turbine Speed Sensor "A" Circuit High When the speed sensor input voltage is higher than 1.8 V for 4.5 seconds or more. (1-trip detection logic)
·

Transmission revolution sensor (speed sensor NT)

·

Transmission wire

·

Wiring harness connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The NT terminal of the ECM detects a revolution signal from the speed sensor (NT) (input RPM). The ECM calculates gear shifts comparing the speed sensor (NT) with the speed sensor (NC).

While the vehicle is being driven in 2nd, 3rd, 4th or 5th gear with the shift lever in D, if the input shaft revolution (speed) is less than 300 rpm*1 and the output shaft revolution (speed) is more than 1000 rpm*2, the ECM interprets this as a fault, illuminates the MIL and stores a DTC.

*1: Pulse is not output or is irregularly output.

*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM

C239276E06
5.646,4.271 6.135,4.469 0.49,0.198 10 false ECM 5.125,1.844 5.448,2 0.323,0.156 10 false NTB 5.125,2.313 5.448,2.469 0.323,0.156 10 false NTO 3.438,1.719 3.76,1.875 0.323,0.156 10 false NTB 3.438,2.188 3.76,2.344 0.323,0.156 10 false NTO 0.438,2.875 2.469,3.042 2.031,0.167 10 false Transmission Revolution Sensor 0.729,3.135 2.354,3.313 1.625,0.177 10 false (Input Speed Sensor NT) 1.438,2.083 1.646,2.229 0.208,0.146 10 false NT 0.917,3.51 2.26,3.708 1.344,0.198 10 false Automatic Transaxle 2.854,3.51 3.927,3.865 1.073,0.354 10 false Wiring Harness Connector 5.646,4.115 5.969,4.271 0.323,0.156 10 false C1 4.74,1.75 5.021,1.906 0.281,0.156 10 false 116 4.74,2.219 5.021,2.375 0.281,0.156 10 false 115 2.906,1.74 3.229,1.896 0.323,0.156 10 false NTB 2.906,2.208 3.229,2.365 0.323,0.156 10 false NTO 2.635,1.625 2.76,1.792 0.125,0.167 10 false 1 2.635,2.094 2.76,2.26 0.125,0.167 10 false 2 2.156,1.74 2.479,1.896 0.323,0.156 10 false NTB 2.156,2.208 2.479,2.365 0.323,0.156 10 false NTO 2.635,1.844 2.771,2 0.135,0.156 10 false A 3.865,2.323 4.188,2.479 0.323,0.156 10 false C2 3.865,1.854 4.188,2.01 0.323,0.156 10 false C2 2.635,2.313 2.771,2.469 0.135,0.156 10 false A 3.917,1.635 4.042,1.802 0.125,0.167 10 false 1 3.917,2.115 4.042,2.281 0.125,0.167 10 false 2

CAUTION / NOTICE / HINT

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NT) Input shaft speed Min.: 0 rpm
Max.: 12750 rpm
Lock-up is
·

ON (after warming up engine): Input turbine speed (NT) is equal to engine speed

·

OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed


Data is displayed in increments of 50 rpm
Powertrain > Engine > Data List
Tester Display
SPD (NT)
50003 234 111
HINT:
·

SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION)
a.

Remove the valve body assembly.


b.
C133219

Make sure that the connector is properly connected, and check the speed sensor installation.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>SPEED SENSOR>INSTALLATION

OK:

The installation bolts are tightened properly and there is no clearance between the sensor and valve body assembly.



Result:
Proceed to
OK
NG



OK

2.INSPECT TRANSMISSION WIRE

NG

REPAIR OR REPLACE TRANSMISSION REVOLUTION SENSOR

2.INSPECT TRANSMISSION WIRE
a.
C275092C01
2.677,1.208 3,1.469 0.323,0.26 1.938,1.042 1.333,2.167 false 2.083,1.042 2.25,2.167 false 1.458,3.948 1,4.333 false 1.688,3.938 2,4.333 false 0.073,0.094 0.385,0.25 0.313,0.156 10 *a 0.5,0.5 0.813,0.656 0.313,0.156 10 *b 0.583,3.094 0.896,3.25 0.313,0.156 10 *c 2.802,1.25 2.958,1.448 0.156,0.198 10 A 1.208,2.198 1.667,2.396 0.458,0.198 10 NTO 2.125,2.198 2.583,2.396 0.458,0.198 10 NTB 0.875,4.365 1.333,4.563 0.458,0.198 10 NTB 1.875,4.365 2.333,4.563 0.458,0.198 10 NTO
*a Component without harness connected
(Transmission Wire)
*b Wiring harness connector side
*c Sensor side


Disconnect the speed sensor connector from the transmission wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NTB) sensor side - A-1 (NTB) wiring harness connector side Always Below 1 Ω
2 (NTO) sensor side - A-2 (NTO) wiring harness connector side Always Below 1 Ω
1 (NTB) sensor side - Body ground and other terminals Always 10 kΩ or higher
2 (NTO) sensor side - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)

NG

3.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C2-1 (NTB) - C1-116 (NTB) Always Below 1 Ω
C2-2 (NTO) - C1-115 (NTO) Always Below 1 Ω
C2-1 (NTB) or C1-116 (NTB) - Body ground and other terminals Always 10 kΩ or higher
C2-2 (NTO) or C1-115 (NTO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT WIRING HARNESS CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT WIRING HARNESS CONNECTOR
a.

Remove the wiring harness connector.

C275093C05
2.458,0.521 2.771,0.76 0.313,0.24 2.5,4.01 2.813,4.25 0.313,0.24 4.031,0.542 4.167,0.25 4.167,0.25 4.25,0.25 false 3.938,0.604 4.167,1.042 4.167,1.042 4.25,1.042 false 3.51,3.896 3.917,3.708 3.917,3.708 4.083,3.708 false 3.396,3.885 3.25,3.708 3.25,3.708 3.083,3.708 false 2.354,1.427 2.667,1.583 0.313,0.156 10 false *a 2.396,0.208 2.708,0.365 0.313,0.156 10 false *b 2.427,3.646 2.74,3.802 0.313,0.156 10 false *c 2.531,0.563 2.844,0.76 0.313,0.198 10 false C2 4.292,0.219 4.75,0.417 0.458,0.198 10 false NTB 4.292,0.969 4.75,1.167 0.458,0.198 10 false NTO 4.125,3.635 4.583,3.833 0.458,0.198 10 false NTO 2.792,3.635 3.25,3.833 0.458,0.198 10 false NTB 2.604,4.042 2.76,4.24 0.156,0.198 10 false A
*a Component without harness connected
(Wiring Harness Connector)
*b ECM side
*c Transmission wire side - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C2-1 (NTB) - A-1 (NTB) Always Below 1 Ω
C2-2 (NTO) - A-2 (NTO) Always Below 1 Ω
C2-1 (NTB) - All other terminals Always 10 kΩ or higher
C2-2 (NTO) - All other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TRANSMISSION REVOLUTION SENSOR

NG

5.REPLACE TRANSMISSION REVOLUTION SENSOR

NEXT

6.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0717, P07BF AND/OR P07C0 OUTPUT AGAIN)
6.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0717, P07BF AND/OR P07C0 OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Clear the DTCs.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

HINT:

Write down the currently output DTCs before clearing them.




e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

f.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only DTC P0717, P07BF or P07C0 is output A
DTCs are not output B




A

B

END