Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019700 AUDIO / VIDEO _0096790 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Map light assembly (telephone microphone assembly)

·

Radio and display receiver assembly

·

Harness or connector

·

Telematics transceiver*



*: w/ Manual (SOS) Switch


WIRING DIAGRAM

E250444E44
0.042,0.01 2.01,0.385 1.969,0.375 12 false w/o Manual (SOS) Switch: 0.042,2.708 2.927,2.969 2.885,0.26 12 false w/ Manual (SOS) Switch: 1.177,0.708 1.573,0.875 0.396,0.167 10 false SNS2 0.115,2.042 2.167,2.615 2.052,0.573 10 false Map Light Assembly (Telephone Microphone Assembly) 1.625,0.604 2.021,0.771 0.396,0.167 10 false 13 1.635,1.406 2.031,1.573 0.396,0.167 10 false 4 5.438,0.604 5.833,0.771 0.396,0.167 10 false 6 5.354,1.396 5.75,1.563 0.396,0.167 10 false 19 1.167,1.49 1.583,1.656 0.417,0.167 10 false MCO- 0.115,1.875 0.531,2.042 0.417,0.167 10 false S1 5.208,2.063 6.917,2.458 1.708,0.396 10 false Radio and Display Receiver Assembly 5.208,1.875 5.625,2.042 0.417,0.167 10 false F71 5.594,0.688 5.99,0.854 0.396,0.167 10 false SNS2 5.594,1.49 6.01,1.656 0.417,0.167 10 false MIN- 1.177,3.406 1.573,3.573 0.396,0.167 10 false SNS2 0.115,4.729 2.198,5.354 2.083,0.625 10 false Map Light Assembly (Telephone Microphone Assembly) 1.625,3.302 2.021,3.469 0.396,0.167 10 false 13 1.635,4.104 2.031,4.271 0.396,0.167 10 false 4 2.917,4.104 3.313,4.271 0.396,0.167 10 false 35 4.083,4.104 4.479,4.271 0.396,0.167 10 false 19 5.438,3.313 5.625,3.49 0.188,0.177 10 false 6 5.354,4.104 5.75,4.271 0.396,0.167 10 false 19 1.167,4.208 1.583,4.375 0.417,0.167 10 false MCO- 3.635,4.198 4.052,4.365 0.417,0.167 10 false MCO- 3.146,4.198 3.563,4.365 0.417,0.167 10 false MCI- 0.115,4.552 0.531,4.719 0.417,0.167 10 false S1 5.208,4.729 6.917,5.167 1.708,0.438 10 false Radio and Display Receiver Assembly 5.208,4.563 5.625,4.729 0.417,0.167 10 false F71 2.833,4.823 4.729,5.188 1.896,0.365 10 false Telematics Transceiver 2.833,4.667 3.25,4.833 0.417,0.167 10 false F140 5.594,3.406 5.99,3.573 0.396,0.167 10 false SNS2 5.604,4.188 6.021,4.354 0.417,0.167 10 false MIN-

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be necessary. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E176671C62
1.479,0.542 1.969,0.833 0.49,0.292 2.094,2.01 2.604,2.677 false 1.594,0.615 1.938,0.813 0.344,0.198 10 false F71 0.208,0.146 1.073,0.75 0.865,0.604 10 false *a 2.479,2.698 3.302,3.146 0.823,0.448 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-19 (MIN-) - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (w/o Manual (SOS) Switch) A
OK (w/ Manual (SOS) Switch) B
NG C




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

B

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Disconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-6 (SNS2) - S1-13 (SNS2) Always Below 1 Ω
F71-19 (MIN-) - S1-4 (MCO-) Always Below 1 Ω
F71-6 (SNS2) or S1-13 (SNS2) - Body ground Always 10 kΩ or higher
F71-19 (MIN-) or S1-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E287094C01
2.656,1.781 2.208,1.417 false 2.406,0.656 1.99,1.198 false 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 2.708,1.698 3.24,1.948 0.531,0.25 10 false SNS2 2.5,0.563 3.031,0.813 0.531,0.25 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F140 Telematics transceiver connector.


b.

Disconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F140-35 (MCI-) - S1-4 (MCO-) Always Below 1 Ω
F140-35 (MCI-) or S1-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Disconnect the F140 Telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-19 (MIN-) - F140-19 (MCO-) Always Below 1 Ω
F71-19 (MIN-) or F140-19 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Disconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-6 (SNS2) - S1-13 (SNS2) Always Below 1 Ω
F71-6 (SNS2) or S1-13 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT TELEMATICS TRANSCEIVER
a.

Reconnect the F140 telematics transceiver connector.


b.

Reconnect the F71 radio and display receiver assembly connector.


c.
E266270C24
1.5,0.583 1.917,0.833 0.417,0.25 0.99,2.604 1.24,2.031 false 1.552,0.625 1.938,0.823 0.385,0.198 10 false F140 0.854,2.646 1.302,2.885 0.448,0.24 10 false MCI- 0.198,0.177 0.51,0.375 0.313,0.198 10 false *a
*a Component with harness connected
(Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F140-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

8.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E287094C01
2.656,1.781 2.208,1.417 false 2.406,0.656 1.99,1.198 false 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 2.708,1.698 3.24,1.948 0.531,0.25 10 false SNS2 2.5,0.563 3.031,0.813 0.531,0.25 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)