Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019700 AUDIO / VIDEO _0096790 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B15C3  Speaker Output Short  


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit
·

Harness or connector

·

Speaker

·

Radio and display receiver assembly

·

Telematics transceiver*



*: w/ Manual (SOS) Switch


WIRING DIAGRAM

E287095E08
0.167,1.135 1.427,1.708 1.26,0.573 10 false Front No. 1 Speaker Assembly RH 2.021,2.208 3.292,2.781 1.271,0.573 10 false Front No. 2 Speaker Assembly RH 3.719,2.083 5.26,2.625 1.542,0.542 10 false Telematics Transceiver*1 0.115,3.708 1.385,4.281 1.271,0.573 10 false Front No. 1 Speaker Assembly LH 1.594,4.656 4.156,4.906 2.563,0.25 10 false Front No. 2 Speaker Assembly LH 0.5,5.26 1.406,5.781 0.906,0.521 10 false Rear Speaker Assembly RH 0.51,6.833 1.417,7.354 0.906,0.521 10 false Rear Speaker Assembly LH 0.417,8.063 2.875,8.333 2.458,0.271 10 false *1: w/ Manual (SOS) Switch 0.427,8.417 2.885,8.688 2.458,0.271 10 false *2: w/o Manual (SOS) Switch 5.438,7.792 7.135,8.375 1.698,0.583 10 false Radio and Display Receiver Assembly 1.542,0.906 1.698,1.104 0.156,0.198 10 false 1 1.542,1.5 1.698,1.698 0.156,0.198 10 false 2 1.948,1.5 2.104,1.698 0.156,0.198 10 false 1 1.958,0.698 2.115,0.896 0.156,0.198 10 false 3 2.146,1.49 2.302,1.688 0.156,0.198 10 false - 2.135,0.708 2.292,0.906 0.156,0.198 10 false + 3.052,0.698 3.375,0.927 0.323,0.229 10 false + 3.094,1.49 3.396,1.719 0.302,0.229 10 false - 3.26,1.49 3.417,1.688 0.156,0.198 10 false 2 3.25,0.708 3.406,0.906 0.156,0.198 10 false 4 3.865,0.708 4.021,0.906 0.156,0.198 10 false 5 3.854,1.5 4.01,1.698 0.156,0.198 10 false 6 3.802,0.917 4.115,1.188 0.313,0.271 10 false *1 3.802,1.708 4.115,1.979 0.313,0.271 10 false *1 4.052,0.833 4.667,1.031 0.615,0.198 10 false SPO+ 4.052,1.604 4.667,1.802 0.615,0.198 10 false SPO- 4.583,0.823 5.198,1.021 0.615,0.198 10 false SPI+ 4.594,1.604 5.208,1.802 0.615,0.198 10 false SPI- 4.979,0.698 5.135,0.896 0.156,0.198 10 false 2 4.99,1.5 5.146,1.698 0.156,0.198 10 false 3 4.969,0.906 5.281,1.177 0.313,0.271 10 false *1 4.979,1.698 5.292,1.969 0.313,0.271 10 false *1 5.708,0.802 6.021,1.073 0.313,0.271 10 false F69 5.708,1.594 6.021,1.865 0.313,0.271 10 false F69 5.771,1.406 5.927,1.604 0.156,0.198 10 false 5 5.771,0.615 5.927,0.813 0.156,0.198 10 false 1 6.063,0.813 6.677,1.01 0.615,0.198 10 false FR+ 6.073,1.594 6.688,1.792 0.615,0.198 10 false FR- 4.344,2.896 4.656,3.167 0.313,0.271 10 false *2 2.01,2.042 2.625,2.24 0.615,0.198 10 false G1 3.729,1.938 4.281,2.24 0.552,0.302 10 false F140 1.542,3.521 1.698,3.719 0.156,0.198 10 false 1 1.542,4.104 1.698,4.302 0.156,0.198 10 false 2 1.948,3.313 2.104,3.51 0.156,0.198 10 false 3 1.948,4.104 2.104,4.302 0.156,0.198 10 false 1 2.146,4.104 2.302,4.302 0.156,0.198 10 false - 2.146,3.313 2.302,3.51 0.156,0.198 10 false + 3.063,3.302 3.396,3.542 0.333,0.24 10 false + 3.063,4.094 3.427,4.333 0.365,0.24 10 false - 3.26,3.302 3.417,3.5 0.156,0.198 10 false 4 3.25,4.104 3.406,4.302 0.156,0.198 10 false 2 1.594,4.49 2.208,4.688 0.615,0.198 10 false G5 5.708,4.219 6.021,4.49 0.313,0.271 10 false F69 5.708,3.427 6.021,3.698 0.313,0.271 10 false F69 5.781,4.021 5.938,4.219 0.156,0.198 10 false 6 5.781,3.24 5.938,3.438 0.156,0.198 10 false 2 6.073,3.427 6.688,3.625 0.615,0.198 10 false FL+ 6.083,4.219 6.698,4.417 0.615,0.198 10 false FL- 0.156,0.969 0.771,1.167 0.615,0.198 10 false H3 0.115,3.531 0.729,3.729 0.615,0.198 10 false I3 0.5,5.083 1.115,5.281 0.615,0.198 10 false J4 0.521,6.656 1.135,6.854 0.615,0.198 10 false K4 1.552,5.104 1.708,5.302 0.156,0.198 10 false 1 1.552,5.688 1.708,5.885 0.156,0.198 10 false 2 1.542,6.688 1.698,6.885 0.156,0.198 10 false 1 1.542,7.25 1.698,7.448 0.156,0.198 10 false 2 5.708,5 6.021,5.271 0.313,0.271 10 false F70 5.708,5.792 6.021,6.063 0.313,0.271 10 false F70 5.708,6.583 6.021,6.854 0.313,0.271 10 false F70 5.708,7.385 6.021,7.656 0.313,0.271 10 false F70 5.771,4.802 5.927,5 0.156,0.198 10 false 1 5.771,5.594 5.927,5.792 0.156,0.198 10 false 3 5.771,6.396 5.927,6.594 0.156,0.198 10 false 2 5.771,7.198 5.927,7.396 0.156,0.198 10 false 6 6.073,5.021 6.688,5.219 0.615,0.198 10 false RR+ 6.073,5.792 6.688,5.99 0.615,0.198 10 false RR- 6.073,6.583 6.688,6.781 0.615,0.198 10 false RL+ 6.073,7.385 6.688,7.583 0.615,0.198 10 false RL- 4.313,0.396 4.625,0.667 0.313,0.271 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be necessary. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/ Manual (SOS) Switch A
w/o Manual (SOS) Switch B




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

B

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)
a.

Disconnect the F69 and F70 radio and display receiver assembly connectors.


b.

Disconnect the F140 telematics transceiver assembly connector.


c.

Disconnect the G5 front No. 2 speaker assembly LH connector.


d.

Disconnect the K4 and J4 rear speaker assembly connectors.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F69-1 (FR+) or F140-2 (SPI+) - Body ground Always 10 kΩ or higher
F69-5 (FR-) or F140-3 (SPI-) - Body ground Always 10 kΩ or higher
F69-2 (FL+) or G5-4 (+) - Body ground Always 10 kΩ or higher
F69-6 (FL-) or G5-2 (-) - Body ground Always 10 kΩ or higher
F70-1 (RR+) or J4-1 - Body ground Always 10 kΩ or higher
F70-3 (RR-) or J4-2 - Body ground Always 10 kΩ or higher
F70-2 (RL+) or K4-1 - Body ground Always 10 kΩ or higher
F70-6 (RL-) or K4-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BODY GROUND)
a.

Disconnect the F140 telematics transceiver connector.


b.

Disconnect the G1 front No. 2 speaker assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F140-5 (SPO+) or G1-4 (+) - Body ground Always 10 kΩ or higher
F140-6 (SPO-) or G1-2 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)
a.

Disconnect the H3 and I3 front No. 1 speaker assembly connectors.


b.

Disconnect the G1 and G5 front No. 2 speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-3 (+) or H3-1 - Body ground Always 10 kΩ or higher
G1-1 (-) or H3-2 - Body ground Always 10 kΩ or higher
G5-3 (+) or I3-1 - Body ground Always 10 kΩ or higher
G5-1 (-) or I3-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

6.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

6.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


c.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

7.INSPECT REAR SPEAKER ASSEMBLY
7.INSPECT REAR SPEAKER ASSEMBLY
a.

Remove the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL


b.

Inspect the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

8.INSPECT TELEMATICS TRANSCEIVER

NG

8.INSPECT TELEMATICS TRANSCEIVER
a.

Remove the telematics transceiver.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.
E169849C05
2.51,1.917 2.677,1.5 2.677,1.5 2.75,1.5 false 2.302,1.906 2.188,1.5 2.188,1.5 2.083,1.5 false 0.781,1.906 0.667,1.5 0.667,1.5 0.583,1.5 false 0.979,1.917 1.146,1.5 1.146,1.5 1.25,1.5 false 2.781,1.417 3.146,1.635 0.365,0.219 10 false SPI+ 1.781,1.417 2.156,1.583 0.375,0.167 10 false SPI- 1.292,1.417 1.781,1.583 0.49,0.167 10 false SPO+ 0.198,1.427 0.667,1.646 0.469,0.219 10 false SPO- 0.167,0.177 0.448,0.417 0.281,0.24 10 false *a
*a Component without harness connected
(Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SPI+) - 5 (SPO+) Always Below 1 Ω
3 (SPI-) - 6 (SPO-) Always Below 1 Ω
2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
2 (SPI+) or 5 (SPO+) - Body ground Always 10 kΩ or higher
3 (SPI-) or 6 (SPO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)
a.

Disconnect the F69 and F70 radio and display receiver assembly connectors.


b.

Disconnect the G1 and G5 front No. 2 speaker assembly connectors.


c.

Disconnect the K4 and J4 rear speaker assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F69-1 (FR+) or G1-4 (+) - Body ground Always 10 kΩ or higher
F69-5 (FR-) or G1-2 (-) - Body ground Always 10 kΩ or higher
F69-2 (FL+) or G5-4 (+) - Body ground Always 10 kΩ or higher
F69-6 (FL-) or G5-2 (-) - Body ground Always 10 kΩ or higher
F70-1 (RR+) or J4-1 - Body ground Always 10 kΩ or higher
F70-3 (RR-) or J4-2 - Body ground Always 10 kΩ or higher
F70-2 (RL+) or K4-1 - Body ground Always 10 kΩ or higher
F70-6 (RL-) or K4-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)
a.

Disconnect the H3 and I3 front No. 1 speaker assembly connectors.


b.

Disconnect the G1 and G5 front No. 2 speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-3 (+) or H3-1 - Body ground Always 10 kΩ or higher
G1-1 (-) or H3-2 - Body ground Always 10 kΩ or higher
G5-3 (+) or I3-1 - Body ground Always 10 kΩ or higher
G5-1 (-) or I3-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

12.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

12.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


c.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

13.INSPECT REAR SPEAKER ASSEMBLY
13.INSPECT REAR SPEAKER ASSEMBLY
a.

Remove the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL


b.

Inspect the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG