Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS) › from 2016.11
RM3160E _52 Drivetrain _019686 DRIVE SHAFT / PROPELLER SHAFT _0295731 FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS)  DISASSEMBLY  


PROCEDURE

Hide 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C108564

Using pliers, separate the front No. 2 axle inboard joint boot clamp as shown in the illustration.


Hide 2.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.


Hide 3.SEPARATE FRONT AXLE INBOARD JOINT BOOT

a.

Separate the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C345674C02
1.448,1.031 0.969,0.5 0.969,0.5 1.917,0.625 true 0.792,0.417 1.104,0.615 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.


d.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
F045046

Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.


f.
C141145C04
2.844,1.031 1.813,1.479 1.813,1.479 2.896,1.104 false 1.625,1.396 1.896,1.646 0.271,0.25 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




h.
C345675

Remove the front axle inboard joint grommet from the front drive inboard joint shaft assembly.


Hide 5.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.


Hide 43474E 6.REMOVE FRONT DRIVE SHAFT DAMPER (w/ Drive Shaft Damper)

a.
C292475

Using needle-nose pliers, separate the 2 front drive shaft damper clamps.


b.

Remove the front drive shaft damper and 2 front drive shaft damper clamps from the front drive outboard joint shaft assembly.


Hide 7.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.
C081167

Using pliers, separate the front No. 2 axle outboard joint boot clamp.


Hide 8.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.


Hide 9.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove the old grease from the outboard joint.


Hide 43410C 10.REMOVE FRONT DRIVE SHAFT BEARING (for AWD)

a.
C092033

Using a snap ring expander, remove the drive shaft hole snap ring.


b.
F040210N02
2.052,0.813 2.052,0.292 2.052,0.292 2.542,0.292 false 2.354,1.094 2.354,0.292 false 2.583,0.208 3.083,0.49 0.5,0.281 10 false SST

Using SST and a press, remove the front drive shaft bearing.

SST
09527-10011  

NOTICE:

Do not drop the front drive inboard joint assembly.