Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296067 ROAD SIGN ASSIST SYSTEM C

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  C1AA2  Vehicle Speed Tolerance Malfunction  


DESCRIPTION

The forward recognition camera receives vehicle speed tolerance signals from the combination meter assembly. If the combination meter assembly detects a vehicle speed tolerance malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA2 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA2 Vehicle Speed Tolerance Malfunction 2 seconds after the engine switch is turned on (IG), a signal from the combination meter assembly indicating an abnormal vehicle speed tolerance is detected by the forward recognition camera for 50 seconds or more.
·

Meter/gauge system

·

Combination meter assembly

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

The road sign assist system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (ON-VEHICLE INSPECTION)
a.

Perform On-vehicle Inspection of the meter/gauge system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION

HINT:

Check the meter function by referring to On-vehicle Inspection for the combination meter assembly.



Result:
Result Proceed to
Combination meter assembly is normal A
Combination meter assembly is malfunctioning B



A

2.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)

B

CHECK METER / GAUGE SYSTEM (SPEEDOMETER MALFUNCTION)

2.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 1 minute or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AA2 is not output A
DTC C1AA2 is output B



A

B

3.REPLACE FORWARD RECOGNITION CAMERA
3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
4.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 1 minute or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AA2 is not output A
DTC C1AA2 is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

REPLACE COMBINATION METER ASSEMBLY