Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296067 ROAD SIGN ASSIST SYSTEM C

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  U0100  Lost Communication with ECM / PCM "A"  U0101  Lost Communication with TCM  U0123  Lost Communication with Yaw Rate Sensor Module  U0129  Lost Communication with Brake System Control Module  U0142  Lost Communication with Body Control Module "B"  U0155  Lost Communication with Combination Meter  


DESCRIPTION

These DTCs are stored when a communication error occurs between the sensors and ECUs.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0100 Lost Communication with ECM / PCM "A" While the vehicle is being driven at 1 km/h or 1 mph or more, a communication error between the ECM and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

ECM

·

Forward recognition camera


U0101 Lost Communication with TCM While the vehicle is being driven at 1 km/h or 1 mph or more, a communication error between the TCM (ECM) and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

TCM (ECM)

·

Forward recognition camera


U0123 Lost Communication with Yaw Rate Sensor Module While the vehicle is being driven at 1 km/h or 1 mph or more, a communication error between the yaw rate sensor (airbag Sensor assembly) and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Yaw rate sensor (Airbag Sensor assembly)

·

Forward recognition camera


U0129 Lost Communication with Brake System Control Module 2 seconds after the engine switch is turned on (IG), a communication error between the skid control ECU (brake actuator assembly) and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Forward recognition camera


U0142 Lost Communication with Body Control Module "B" 2 seconds after the engine switch is turned on (IG), a communication error between the main body ECU (multiplex network body ECU) and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Main body ECU (Multiplex network body ECU)

·

Forward recognition camera


U0155 Lost Communication with Combination Meter 2 seconds after the engine switch is turned on (IG), a communication error between the combination meter assembly and the forward recognition camera is detected for approximately 50 seconds or more.
·

CAN communication system

·

Combination meter assembly

·

Forward recognition camera



PROCEDURE

1.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 1 minute or more.

2.

Drive the vehicle at a speed of 1 km/h or 1 mph or more for 5 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC U0100, U0101, U0123, U0129, U0142 and U0155 are not output A
DTC U0100, U0101, U0123, U0129, U0142 or U0155 is output B



A

B