Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0109815 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Main Indicator Light Circuit  


DESCRIPTION

The ECM illuminates the cruise control indicator by sending indicator output demand signals to the combination meter assembly via CAN communication. The cruise control indicator illuminates when the cruise control system is turned on using the cruise control main switch (ON-OFF button). If a malfunction is detected, the cruise control indicator turns off and a warning message is displayed. The cruise control indicator circuit uses CAN communication. If the cruise control indicator is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the cruise control indicator by performing the Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All Test possible at vehicle speed of 0 km/h (0 mph)
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7

Result:
Result Proceed to
The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. A
The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test. B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Enter the following menus: Powertrain / Cruise Control*1 or Radar Cruise 1*2 / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
CCS Ready M-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes -
CCS Indicator M-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes -
Cancel Switch Cruise control indicator status ON or OFF ON: Cruise control indicator illuminates
OFF: Cruise control indicator turns off
-
Powertrain > Cruise Control > Data List
Tester Display
Main SW M-CPU
CCS Ready M-CPU
CCS Indicator M-CPU
50003 237 16,14,12
Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cruise Ready Main-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes -
Cruise Ready Sub-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes -
Cruise Indicator Cruise control indicator status ON or OFF ON: Cruise control indicator illuminates
OFF: Cruise control indicator turns off
-
Powertrain > Radar Cruise1 > Data List
Tester Display
Cruise Ready Main-CPU
Cruise Ready Sub-CPU
Cruise Indicator
50003 374 22,21,17

*1: for 1AR-FE

*2: for 2GR-FKS


Result:
Result Proceed to
The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch (ON-OFF button). A
The cruise control indicator does not illuminate but the Data List item Cruise Indicator changes according to the operation of the cruise control main switch (ON-OFF button). B
The cruise control indicator does not illuminate and the Data List item Cruise Indicator does not change according to the operation of the cruise control main switch (ON-OFF button). C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C