Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0109815 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the cruise control system to enter self-diagnostic mode.

HINT:

When a particular warning light remains blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in the relevant ECU is suspected.


WIRING DIAGRAM

E269391E46
1.271,1.135 1.688,1.406 0.417,0.271 10 false TC 1.25,2.25 1.667,2.521 0.417,0.271 10 false CG 1.563,1 1.979,1.271 0.417,0.271 10 false 13 1.594,2.104 2.01,2.375 0.417,0.271 10 false 4 0.76,3.302 1.177,3.573 0.417,0.271 10 false F25 1.135,3.302 1.885,3.594 0.75,0.292 10 false DLC3 5.854,1.135 6.271,1.406 0.417,0.271 10 false TC 5.833,3.313 6.25,3.583 0.417,0.271 10 false A43 6.198,3.313 6.615,3.583 0.417,0.271 10 false ECM 5.531,0.979 6.469,1.177 0.938,0.198 10 false 23

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - ECM)
a.

Disconnect the A43 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-23 (TC) - F25-13 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DLC3 - ECM)

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)
a.
E265513C30
1.5,0.417 1.854,0.635 0.354,0.219 0.5,0.552 1.229,0.552 1.229,0.552 1.583,1.063 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 1.563,0.438 2.021,0.635 0.458,0.198 10 false F25 0.24,0.469 0.552,0.667 0.313,0.198 10 false CG
*a DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F25-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DLC3 - BODY GROUND)

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)
a.
E265513C31
1.5,0.417 1.885,0.646 0.385,0.229 2.833,2 2.365,2 2.365,2 1.771,1.625 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 1.573,0.448 2.031,0.646 0.458,0.198 10 false F25 2.927,1.917 3.24,2.115 0.313,0.198 10 false TC
*a DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F25-13 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU