GENERAL
The cruise control main switch is used to turn the dynamic radar cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it.
The dynamic radar cruise control system has two cruise control modes: constant speed control mode and vehicle-to-vehicle distance control mode
Vehicle-to-vehicle distance control mode is selected by default when the dynamic radar cruise control system is turned on using the cruise control main switch (ON-OFF button).
Operation of constant speed control mode is the same as that for a conventional cruise control system.
This system maintains the vehicle at the speed that the driver has set, as long as there are no vehicles ahead. In addition to this, the system maintains the vehicle-to-vehicle distance that has been set by the driver. If the system detects a vehicle driving at a slower speed ahead while the driver is driving at a constant speed, it controls the engine to decelerate the vehicle. If further deceleration is required, the system controls the brake actuator assembly (skid control ECU) in order to apply the brakes. Thereafter, if there are no vehicles ahead within the set vehicle-to-vehicle distance because either the vehicle ahead or the driver has changed lanes, the system accelerates slowly to reach the set speed and resumes driving at this speed.
Vehicle-to-vehicle distance control mode is designed to control vehicle speed and vehicle-to-vehicle distance using the constant speed function, deceleration cruising function, follow-up cruising function, and acceleration cruising function.
The millimeter wave radar sensor assembly, forward recognition camera and driving support ECU assembly control the system while vehicle-to-vehicle distance control mode is operating, and send signals to each actuator and ECU.
In vehicle-to-vehicle distance control mode, the dynamic radar cruise control system receives signals from the forward recognition camera, yaw rate and acceleration sensor (airbag sensor assembly) and the steering sensor. Based on these signals, the system then estimates curve radius and compensates for information on the preceding vehicle while turning. It can also compensate using brake control when approaching another vehicle.
This system judges the presence of a vehicle in front and the distance to it based on the signals from the millimeter wave radar sensor assembly and forward recognition camera while vehicle-to-vehicle distance control mode is operating. Using this information, the system informs the driver of danger with the warning buzzer, performs brake control, and turns on the stop lights when approaching a vehicle in front.
The dynamic radar cruise control system performs the following controls (example).
Vehicle distance increases and decreases in accordance with vehicle speed.
Control conditions are indicated on the multi-information display in the combination meter assembly.
| *1 | Drives the vehicle at a constant speed (set speed: 100 km/h (60 mph)) | *2 | Decelerates the vehicle from the set speed to the speed of the preceding vehicle (80 km/h (50 mph))* |
| *3 | Follows the preceding vehicle while maintaining an appropriate vehicle-to-vehicle distance according to the speed of the preceding vehicle | *4 | Gradually accelerates the vehicle to the set speed and maintains the speed |
*: Throttle valve control and brake control are performed to decelerate the vehicle. If deceleration is insufficient and the distance to the preceding vehicle becomes too short, the vehicle approach warning buzzer sounds to warn the driver to take an appropriate action (braking, etc.).
FUNCTION OF MAIN COMPONENTS
The main components of the dynamic radar cruise control system have the following functions:
| Component | Outline | |
|---|---|---|
| Combination Meter Assembly | Cruise Control Indicator (Vehicle-to-vehicle Distance Control Mode) | ·
Illuminates based on signals from the ECM when the dynamic radar cruise control system is turned on using the cruise control main switch (ON-OFF button). ·
Turns off based on signals from the ECM or driving support ECU assembly when a malfunction is detected in the dynamic radar cruise control system. |
| Cruise Control Indicator (Constant Speed Control Mode) | Illuminates when the dynamic radar cruise control system is turned on using the cruise control main switch (ON-OFF button) and constant speed control mode is selected. | |
| Cruise Control SET Indicator | Illuminates when the vehicle speed is set. | |
| Multi-information Display | ·
Displays dynamic radar cruise control system information based on signals from the ECM when the dynamic radar cruise control system is turned on using the cruise control main switch (ON-OFF button). ·
Displays a warning message if the ECM or driving support ECU assembly detects a malfunction signal while the dynamic radar cruise control system is controlling vehicle speed. |
|
| Warning Buzzer | Sounds once to inform the ECM or driver if the driving support ECU assembly detects an automatic cancel signal while the dynamic radar cruise control system is controlling vehicle speed. | |
| Cruise Control Main Switch | ON-OFF Button | ·
Turns the dynamic radar cruise control system on and off. ·
Switches the control mode between constant speed control mode and vehicle-to-vehicle distance control mode. |
| CANCEL Switch | A cancel signal is sent to the ECM when the switch is operated. | |
| +RES Switch | Acceleration and stored speed resume signals are sent to the ECM when the switch is operated. | |
| -SET Switch | Deceleration and vehicle speed setting signals are sent to the ECM when the switch is operated. | |
| Vehicle-to-vehicle Distance Control Switch (Steering Pad Switch Assembly) | When vehicle-to-vehicle distance control mode is controlling vehicle speed, the driver can operate the switch to select the vehicle-to-vehicle distance in 3 stages: long, middle, and short. | |
| Stop Light Switch Assembly | Outputs brake pedal depression signals to the ECM. | |
| Millimeter Wave Radar Sensor Assembly | Sends information such as vehicle-to-vehicle distance, relative speed and presence of a vehicle in front to the driving support ECU assembly based on reflected millimeter waves. | |
| Forward Recognition Camera | Captures the image in front of the vehicle to detect lane markers and objects on the road ahead. | |
| Steering Sensor | Outputs steering angle signals to the driving support ECU assembly. | |
| Speed Sensor | Outputs wheel speed signals to the skid control ECU (Brake Actuator Assembly). | |
| Airbag Sensor Assembly (Yaw Rate and Acceleration Sensor) | Outputs yaw rate signals to the driving support ECU assembly. | |
| Brake Actuator Assembly (Skid Control ECU) | Operates the brake actuator assembly in accordance with brake request signals received from the ECM when the dynamic radar cruise control system is in vehicle-to-vehicle distance control mode. | |
| Skid Control Buzzer Assembly | Sounds upon receiving signals from the driving support ECU assembly. | |
| ECM | ·
Controls the dynamic radar cruise control system in accordance with signals received from switches, sensors, and the driving support ECU assembly. ·
Stores DTCs if a malfunction is detected in the dynamic radar cruise control system. |
|
| Throttle with Motor Body Assembly | Throttle Control Motor | Adjusts the throttle valve opening angle in accordance with signals received from the ECM. |
| Throttle Position Sensor | Outputs the throttle valve opening angle to the ECM. | |
| Driving Support ECU Assembly | ·
Detects a preceding vehicle based on signals from the millimeter wave radar sensor assembly when the dynamic radar cruise control system is in vehicle-to-vehicle distance control mode. Then, the driving support ECU assembly calculates the acceleration or deceleration required to achieve the target vehicle-to-vehicle distance, and outputs request signals to the ECM. ·
Stores DTCs if a malfunction is detected in the dynamic radar cruise control system. |
|
| Park/Neutral Position Switch Assembly | Outputs the shift lever position to the ECM. | |
| VSC OFF Switch | Outputs VSC off signals to the skid control ECU (Brake Actuator Assembly). | |
| Transmission Floor Shift Assembly | Transmission Control Switch | While the vehicle is being driven in S mode, outputs "+" (upshift) or "-" (downshift) request signals to the ECM. |
OPERATION OF DYNAMIC RADAR CRUISE CONTROL
Controls performed by the dynamic radar cruise control system in each control mode (constant speed control mode and vehicle-to-vehicle distance control mode) are as follows:
| Mode | Outline |
|---|---|
| Constant Speed Control Mode | Operation of constant speed control mode is the same as that for the conventional cruise control system. However, the difference is as follows:
·
The lowest possible set speed for the conventional cruise control system is approximately 50 km/h (31 mph) for the dynamic radar cruise control system (constant speed control mode). |
| Vehicle-to-vehicle Distance Control Mode | In vehicle-to-vehicle distance control mode, the system detects a preceding vehicle and maintains an appropriate vehicle-to-vehicle distance according to the speed of the preceding vehicle (follow-up control).
·
The driver can operate the vehicle-to-vehicle distance control switch (steering pad switch assembly) to select the vehicle-to-vehicle distance in 3 levels: long, middle, or short. ·
The mode performs 4 controls: constant speed control, deceleration control, follow-up control, and acceleration control. |
Vehicle-to-vehicle Distance Control Mode:
Constant Speed Control Mode: