Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296315 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE)  U0100  Lost Communication with ECM / PCM "A"  U0122  Lost Communication with Vehicle Dynamics Control Module  U0125  Lost Communication with Yaw Rate Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  U0129  Lost Communication with Brake System Control Module  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The ECM and driving support ECU assembly communicates with each sensor and ECU via CAN communication.

If any malfunction is detected in a CAN communication circuit, one or more CAN communication system DTCs are stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0100 Lost Communication with ECM / PCM "A"
Condition 1:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the ECM and the driving support ECU assembly is detected for approximately 1 second or more.


Condition 2:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the ECM continuously receives a communication cut-off signal from the skid control ECU (brake actuator assembly) for approximately 1 second or more.


Condition 1:
·

CAN communication system

·

ECM

·

Driving support ECU assembly


Condition 2:
·

CAN communication system

·

ECM

·

Skid control ECU (brake actuator assembly)


U0122 Lost Communication with Vehicle Dynamics Control Module When the engine switch is on (IG) and the dynamic radar cruise control system is operating, a communication error between the skid control ECU (brake actuator assembly) and the ECM is detected for approximately 2.6 seconds or more.
·

CAN communication system

·

ECM

·

Skid control ECU (brake actuator assembly)


U0125 Lost Communication with Yaw Rate Sensor Module While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the yaw rate and acceleration sensor (airbag sensor assembly) and the driving support ECU assembly is detected for approximately 1 second or more.
·

CAN communication system

·

Airbag sensor assembly (yaw rate and acceleration sensor)

·

Driving support ECU assembly


U0126 Lost Communication with Steering Angle Sensor Module While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the steering sensor and the driving support ECU assembly is detected for approximately 1 second or more.
·

CAN communication system

·

Steering sensor

·

Driving support ECU assembly


U0129 Lost Communication with Brake System Control Module While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the skid control ECU (brake actuator assembly) and the driving support ECU assembly is detected for approximately 2.5 seconds or more.
·

CAN communication system

·

Brake actuator assembly (skid control ECU)

·

Driving support ECU assembly


U1104 Lost Communication with Driving Support ECU
Condition 1:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for approximately 0.2 seconds or more.


Condition 2:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the driving support ECU assembly and ECM is detected for 1 second or more.


Condition 1:
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


Condition 2:
·

CAN communication system

·

ECM

·

Driving support ECU assembly



PROCEDURE

1.CHECK FOR DTCs
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE)>DTC CHECK / CLEAR

Powertrain > Radar Cruise1 > Clear DTCs
50002 239
Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the following conditions are not met, the system cannot detect the malfunction.

1.

Turn the engine switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Drive the vehicle at 36 km/h (22 mph) or more for 3 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE)>DTC CHECK / CLEAR

Powertrain > Radar Cruise1 > Trouble Codes
50001 239
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC U0100, U0122, U0125, U0126, U0129 and U1104 are not output A
DTC U0100, U0122, U0125, U0126, U0129 or U1104 is output B



A

B