Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.11
RM3160E _53 Suspension _060167 TIRE PRESSURE MONITORING _0296404 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2121/21  No Signal from Transmitter ID1  C2122/22  No Signal from Transmitter ID2  C2123/23  No Signal from Transmitter ID3  C2124/24  No Signal from Transmitter ID4  C2125/25  No Signal from Transmitter ID5  C2181/81  Transmitter ID1 not Received (Test Mode DTC)  C2182/82  Transmitter ID2 not Received (Test Mode DTC)  C2183/83  Transmitter ID3 not Received (Test Mode DTC)  C2184/84  Transmitter ID4 not Received (Test Mode DTC)  C2185/85  Transmitter ID5 not Received (Test Mode DTC)  


DESCRIPTION

The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure value is less than this threshold, the warning light in the combination meter assembly illuminates.

The tire pressure warning valve and transmitters constantly send radio waves to the tire pressure warning ECU and receiver.

Under the conditions below, the tire pressure warning ECU and receiver is unable to receive the signals from the tire pressure warning valve and transmitters, and a DTC is stored.

·

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

·

Devices using similar radio frequencies are used in the vehicle.

·

The ID of a tire pressure warning valve and transmitter is mistyped during registration.

·

A tire, wheel and/or transmitter from a different vehicle is installed.


HINT:

When no transmitter ID is received from a tire pressure warning valve and transmitter for 20 minutes or more while the vehicle speed is more than 40 km/h (25 mph), or no transmitter ID is received from all of the tire pressure warning valve and transmitters for 20 minutes or more, DTCs from C2121/21 to C2125/25 are stored.

DTCs C2121/21 to C2125/25 can only be cleared by using the GTS. DTCs C2181/81 to C2185/85 can be cleared when the tire pressure warning valve and transmitter sends a forced transmission signal or test mode ends. DTCs C2181/81 to C2185/85 are output only in test mode.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2121/21 No Signal from Transmitter ID1 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2122/22 No Signal from Transmitter ID2 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2123/23 No Signal from Transmitter ID3 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2124/24 No Signal from Transmitter ID4 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2125/25 No Signal from Transmitter ID5 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2181/81 Transmitter ID1 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2182/82 Transmitter ID2 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2183/83 Transmitter ID3 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2184/84 Transmitter ID4 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2185/85 Transmitter ID5 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-

NOTICE:

When DTCs C2121/21 to C2125/25 are set, DTC C2179/79 may be set simultaneously. In such cases, troubleshoot DTCs C2121/21 to C2125/25 first, then troubleshoot DTC C2179/79.


HINT:

It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


WIRING DIAGRAM

C269188E17
5.969,3.885 6.604,4.083 0.635,0.198 10 false RDA 5.969,4.344 6.646,4.531 0.677,0.188 10 false PRG 4.302,3.854 4.646,4.021 0.344,0.167 10 false RDA 4.302,4.302 4.646,4.469 0.344,0.167 10 false PRG 5.99,6.49 6.469,6.656 0.479,0.167 10 false CLSW 5.781,6.438 5.927,6.604 0.146,0.167 10 false 3 6,7.042 6.479,7.208 0.479,0.167 10 false GND 5.719,6.99 5.948,7.156 0.229,0.167 10 false 12 2.427,6.458 2.594,6.625 0.167,0.167 10 false 2 3.51,6.469 3.667,6.635 0.156,0.167 10 false 1 5.771,4.229 5.938,4.396 0.167,0.167 10 false 5 5.771,3.781 5.958,3.948 0.188,0.167 10 false 4 5.708,7.802 7.115,8.333 1.406,0.531 10 false Tire Pressure Warning ECU and Receiver 1.906,6.99 4.208,7.219 2.302,0.229 10 false Tire Pressure Warning Reset Switch 5.708,7.635 6.573,7.802 0.865,0.167 10 false M45 2.802,0.281 4.906,0.635 2.104,0.354 10 false Tire Pressure Warning Valve and Transmitter 0.292,0.927 2.313,1.385 2.021,0.458 10 false Tire Pressure Warning Valve and Transmitter 2.823,1.573 4.917,1.927 2.094,0.354 10 false Tire Pressure Warning Valve and Transmitter 0.302,2.219 2.354,2.677 2.052,0.458 10 false Tire Pressure Warning Valve and Transmitter 0.604,7.385 1.688,7.604 1.083,0.219 10 false : Radio Waves 0.563,7.74 2.406,7.958 1.844,0.219 10 false : CAN Communication Line 2.135,5.885 2.583,6.052 0.448,0.167 10 false DLC3 2.115,4.875 4.135,5.042 2.021,0.167 10 false Combination Meter Assembly 2.115,5.188 4.094,5.573 1.979,0.385 10 false - Tire Pressure Warning Light 2.448,3.792 4.083,4.24 1.635,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 4.729,3.792 5,3.958 0.271,0.167 10 false 4 4.729,4.229 4.917,4.396 0.188,0.167 10 false 5 2.135,3.792 2.479,3.958 0.344,0.167 10 false F19 1.906,6.792 2.271,6.969 0.365,0.177 10 false F138 2.781,2.906 4.875,3.26 2.094,0.354 10 false Tire Pressure Warning Valve and Transmitter 3.24,6.688 3.698,6.885 0.458,0.198 10 false INT 2.615,6.667 2.771,6.865 0.156,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.



PROCEDURE

1.CHECK FREQUENCY RECEIVING CONDITION
a.

Check that the following conditions are not met:

i.

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

HINT:

If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking 1 minute due to interfering radio frequencies.



ii.

Devices using similar radio frequencies are used in the vehicle.

OK:

Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.


HINT:

Radio transmissions may be interrupted due to the surroundings or devices installed by the user.




Result:
Proceed to
OK
NG



OK

2.IDENTIFY TRANSMITTER CORRESPONDING TO DTC

NG

CHECK IF ANY DEVICE IS INSTALLED BY USER

2.IDENTIFY TRANSMITTER CORRESPONDING TO DTC
a.

Set the tire pressure to the specified value.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Display the "ID Tire Inflation Pressure" value for each wheel using the GTS.


h.

Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kg/cm2, 5.8 psi) within 30 seconds. If the "ID Tire Inflation Pressure" value displayed on the GTS does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" value was the cause of the output DTC.

HINT:
·

Identify the malfunctioning tire pressure warning valve and transmitter by repeatedly decreasing the tire pressure for each tire.

·

Record which "ID Tire Inflation Pressure" value corresponds to each tire.



Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40
HINT:

*1: It may take a few minutes until the values are displayed.



i.

Check the Data List.

NOTICE:
·

It may take a few minutes until the values are displayed.

·

When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.

·

Record the transmitter IDs and positions of transmitters that are normal.




j.

After confirming that the "ID Tire Inflation Pressure" value for one tire has changed, repeat this procedure one by one. Identify the transmitter that corresponds to the DTC.


Result:
Result Proceed to
One or more transmitter is abnormal A
All transmitters are normal B



A

3.CHECK TRANSMITTER ID

B

END

3.CHECK TRANSMITTER ID
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID4 displayed -
Registered ID 5 Code Registered ID5 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID5 displayed -
Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
Registered ID 5 Code
50003 203 7,8,9,10,11
HINT:

*1: Displayed only when the ID No. is not registered.



g.

Check the ID number on the identified transmitter by removing it from the tire and wheel.

C353321C03
6.031,1.313 6.156,0.719 6.156,0.719 6.302,0.719 false 0.271,0.229 0.583,0.427 0.313,0.198 10 false *1 6.354,0.656 6.667,0.854 0.313,0.198 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) - -



h.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B



A

4.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

5.REGISTRATION OF TRANSMITTER ID
4.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
a.

Replace the tire pressure warning valve and transmitter.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.REGISTRATION OF TRANSMITTER ID
5.REGISTRATION OF TRANSMITTER ID

Result:
Proceed to
NEXT



NEXT

6.PERFORM INITIALIZATION
6.PERFORM INITIALIZATION

Result:
Proceed to
NEXT



NEXT

7.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
7.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40
HINT:
·

*1: It may take a few minutes until the values are displayed.

·

When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.




Result:
Result Proceed to
Tire pressure values are not displayed. A
All tire pressure readings are equal to specified values. B



A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

END