Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.11
RM3160E _53 Suspension _060167 TIRE PRESSURE MONITORING _0296404 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light illuminates and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2198/98 Initialization Switch (for Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Wire harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C354516E12
5.24,1.917 6.615,2.406 1.375,0.49 10 false Tire Pressure Warning ECU and Receiver 5.458,1.01 6.833,1.5 1.375,0.49 10 false CLSW 1.865,1.438 4.573,1.646 2.708,0.208 10 false Tire Pressure Warning Reset Switch 1.885,1.25 3.26,1.74 1.375,0.49 10 false F138 2.313,0.896 2.583,1.229 0.271,0.333 10 false 2 3.417,0.885 3.688,1.219 0.271,0.333 10 false 1 2.49,0.896 2.76,1.229 0.271,0.333 10 false E 3.104,0.906 3.375,1.24 0.271,0.333 10 false INT 5.271,0.896 5.542,1.229 0.271,0.333 10 false 3 5.24,1.74 6.615,2.229 1.375,0.49 10 false M45

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.

Remove the tire pressure warning reset switch.


b.
C239105C04
2.552,1.26 2.417,1.625 true 2.865,1.25 3.01,1.625 true 0.135,0.094 0.427,0.427 0.292,0.333 10 false *a 1.438,1.146 1.688,1.292 0.25,0.146 10 false *b 1.844,1.677 2.156,1.823 0.313,0.146 10 false *c 2.365,1.635 2.604,1.844 0.24,0.208 10 false E 2.917,1.646 3.271,1.927 0.354,0.281 10 false INT
*a Component without harness connected
(Tire Pressure Warning Reset Switch)
*b On
*c Off


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (INT) - 2 (E) On Below 1 Ω
Off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the F138 tire pressure warning reset switch connector.


b.

Disconnect the M45 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M45-3 (CLSW) - F138-1 (INT) Always Below 1 Ω
M45-3 (CLSW) or F138-1 (INT) - Body ground Always 10 kΩ or higher
F138-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR