Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2016.11
RM3160E _55 Steering _019697 POWER ASSIST SYSTEMS _0104490 POWER STEERING SYSTEM U

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Meter Vehicle Velocity Vehicle speed from speedometer Min.: 0.0 km/h (0.0 MPH)
Max.: 300.0 km/h (186.4 MPH)
·

0 km/h (0 MPH): Engine running and vehicle stopped

·

No significant fluctuation: Engine running and vehicle driven at a constant speed


-
Engine Revolution Engine speed Min.: 0 rpm
Max.: 12800 rpm
No significant fluctuation Engine running at a constant speed
Motor Actual Current Amount of current to motor Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
- The value increases when turning left and decreases when turning right
Engine running and steering wheel being turned
Command Value Current Requested current to motor Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
- The value increases when turning left and decreases when turning right
Engine running and steering wheel being turned
Steering Angle Velocity Steering angle speed Min.: -32768 deg/s
Max.: 32767 deg/s
Value changes in proportion to steering speed
- The value increases when turning left and decreases when turning right
Engine running and steering wheel being turned
Thermistor Temperature ECU substrate temperature Min.: -40.0°C (-40.0°F)
Max.: 150.0°C (302.0°F)
-40°C to 150°C (-40°F to 302°F) -
PIG Power Supply Power source voltage to active motor Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Always
IG Power Supply IG power source voltage Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Ignition switch ON
Steering Wheel Torque Steering wheel torque Min.: -327.68 Nm
Max.: 7.00 Nm
Value changes in proportion to steering effort
- The value increases when turning right and decreases when turning left
Engine running and steering wheel being turned
Motor Rotation Angle Motor rotation angle Min.: 0.000 deg
Max.: 1441.770 deg
During steering operation, motor rotation angle value changes from 0 to 360° Engine running and steering wheel being turned
Motor Voltage Motor power supply voltage Min.: 0.000 V
Max.: 98.000 V
9 to 16 V Engine running and steering wheel being turned
Motor Terminal Volt(U) Motor terminal voltage (U phase) Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Engine running and steering wheel being turned
Motor Terminal Volt(V) Motor terminal voltage (V phase) Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Engine running and steering wheel being turned
Motor Terminal Volt(W) Motor terminal voltage (W phase) Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Engine running and steering wheel being turned
Torque Sensor 1 Output Torque sensor 1 output value Min.: 0.0000 V
Max.: 4.9725 V
·

2.3 to 2.7 V: Engine running and steering wheel not being turned (without load)

·

2.5 to 4.7 V: Engine running and steering wheel being turned to right with vehicle stopped

·

0.3 to 2.5 V: Engine running and steering wheel being turned to left with vehicle stopped


-
Torque Sensor 2 Output Torque sensor 2 output value Min.: 0.0000 V
Max.: 4.9725 V
·

2.3 to 2.7 V: Engine running and steering wheel not being turned (without load)

·

0.3 to 2.5 V: Engine running and steering wheel being turned to right with vehicle stopped

·

2.5 to 4.7 V: Engine running and steering wheel being turned to left with vehicle stopped


-
IG ON/OFF Times Number of times of ignition switch on/off after fail detection Min.: 0 times
Max.: 65535 times
- This value indicates the number of times of ignition switch on/off after the latest DTC detection.
Motor Overheat Record Continuous overheat prevention control record Unrec or Rec Unrec Unrec: Unrecorded
Rec: Recorded
Motor Lo Power Record PIG power source voltage drop record Unrec or Rec Unrec Unrec: Unrecorded
Rec: Recorded
Eng Rev Inter Record Record of engine signal interruption Unrec or Rec Unrec Unrec: Unrecorded
Rec: Recorded
Spd Sig Invalid Record Record of vehicle speed signal invalid Unrec or Rec Unrec Unrec: Unrecorded
Rec: Recorded
Battery Voltage Lo Record Battery voltage reduction history Min.: 0 times
Max.: 65535 times
0 to 65535 times -
Battery Control Count (Body ECU) Number of battery load control operations Min.: 0 times
Max.: 65535 times
- -
Battery Voltage Battery voltage Min.: 0.0 V
Max.: 25.5 V
9 to 16 V Always
PS Assist Signal Status of the record of power steering assist signal OFF or ON OFF: Ignition switch to ON
ON: Engine running
-
Motor Overheat Limit Cnt(Normal) Number of times that assist limit was performed according to the estimated temperature of the portion where heat was generated in the power steering ECU assembly and motor coil Min.: 0 times
Max.: 255 times
- -
Assist Limit Cnt(Power Voltage Low) Number of times that assist limit was performed due to battery voltage having dropped to 9 V or below Min.: 0 times
Max.: 255 times
- -
Power Vol Low Prevention Limit Cnt Number of times that assist limit was performed due to battery voltage having dropped to 9.7 V or below Min.: 0 times
Max.: 255 times
- -
Eng Stall/Ready OFF Cnt Number of times that assist limit was performed after the engine stalled and the ignition switch was turned off Min.: 0 times
Max.: 255 times
- -
Motor Overheat Limit Cnt(Motor Overload) Number of times that assist limit was performed to prevent the system from overheating in a case where the motor is overloaded because it is locked due to the steering wheel being turned to the full lock position or a tire hitting a curb Min.: 0 times
Max.: 255 times
- -
Assist Limit Record 1 Information of assist limit that was used in the past or is currently in use (latest history) Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, Vhcl Spd Sig Malf, Batt Vol Keep - -
Record 1 Key Cycle Number of times that the ignition switch was turned ON before Assist Limit Record 1 was stored Min.: 0 times
Max.: 65535 times
- -
Record 1 Key Cycle Elapsed Time Period of time that elapsed after the ignition switch was turned ON before Assist Limit Record 1 was stored Min.: 0.0 s
Max.: 53687091.1 s
- -
Assist Limit Record 2 Information of assist limit that was used in the past (second latest history) Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, Vhcl Spd Sig Malf, Batt Vol Keep - -
Record 2 Key Cycle Number of times that the ignition switch was turned ON after Assist Limit Record 2 was stored before Assist Limit Record 1 was stored Min.: 0 times
Max.: 65535 times
- -
Record 2 Key Cycle Elapsed Time Period of time that elapsed after the ignition switch was turned ON before Assist Limit Record 2 was stored Min.: 0.0 s
Max.: 53687091.1 s
- -
Assist Limit Record 3 Information of assist limit that was used in the past (third latest history) Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, Vhcl Spd Sig Malf, Batt Vol Keep - -
Record 3 Key Cycle Number of times that the ignition switch was turned ON after Assist Limit Record 3 was stored before Assist Limit Record 2 was stored Min.: 0 times
Max.: 65535 times
- -
Record 3 Key Cycle Elapsed Time Period of time that elapsed after the ignition switch was turned ON before Assist Limit Record 3 was stored Min.: 0.0 s
Max.: 53687091.1 s
- -
Current Key Cycle Number of current trip Min.: 0 times
Max.: 65535 times
- -
Current Key Cycle Elapsed Time Time elapsed since ignition switch was turned ON Min.: 0.0 s
Max.: 53687091.1 s
- -
The Number of DTCs Number of detected DTCs when freeze frame data stored Min.: 0
Max.: 255
0 to 255 -
HINT:
·

With the vehicle stopped or driving very slowly, if the steering wheel is turned repeatedly or turned to a lock position and the vehicle is driven for an extended period of time, the amount of power assist is decreased to prevent overheating of the motor and ECU. If this occurs, idle the engine and do not turn the steering wheel for approximately 10 minutes to improve power assist.

·

If the battery is not sufficiently charged or the voltage decreases temporarily, the amount of power assist is reduced and the EPS warning light comes on. In such cases, the amount of power assist returns to normal when the battery voltage recovers.

·

When the value displayed for "Battery Control Count (Body ECU)" in the Data List is not 0 with the battery voltage low, the system is limiting the seat heater, rear window defogger and windshield deicer operation. In this case, inspect the charging system.

for 1AR-FE: Click herePower Source / Network>1AR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

for 2GR-FKS: Click herePower Source / Network>2GR-FKS BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION