ENTER TEST MODE
By performing a test call, it is possible to check the operation of the telematics transceiver.
Make sure to perform a test call after troubleshooting the telematics system.
Depending on radio wave signal conditions and the test center condition, a test call may fail even though the vehicle is not malfunctioning.
Enter test mode by using either of the following methods:
Method 1 (Recommended)
Connect the GTS to the DLC3.
Turn the engine switch on (IG)
Turn the GTS on.
Enter the following menus: Body Electrical / Telematics / Utility / Emergency Call Check
| Tester Display |
|---|
| Emergency Call Check |
According to the display on the GTS, perform Emergency Call Check to enter test mode.
Method 2
Turn the taillights on and off at an interval of 10 seconds or less as follows:
Operate the light control switch as follows: Off → Tail → Off → Tail → Off → Tail → Off → Tail → Off → Tail →Off → Tail → Off → Tail → Off → Tail → Off → Tail → Off → Tail.
Expose the automatic light control sensor to a light and then operate the light control switch as follows: AUTO → Tail → AUTO → Tail → AUTO → Tail → AUTO → Tail → AUTO → Tail →AUTO → Tail → AUTO → Tail → AUTO → Tail → AUTO → Tail → AUTO → Tail.
Turn the light control switch to the AUTO position, expose the automatic light control sensor to a light and then cover and uncover the light control sensor to turn the taillights on and off as follows: Off → On → Off → On → Off → On → Off → On → Off → On →Off → On → Off → On → Off → On → Off → On → Off → On.
| *a | Manual (SOS) Switch Green Indicator |
| *b | Manual (SOS) Switch Red Indicator |
Check that the manual (SOS) switch indicators begin blinks 5 times over 10 seconds and then turn off. Push the manual (SOS) switch for less than 3 seconds within 15 seconds after the indicators begin to blink to enter test mode.
PERFORM TEST CALL
Enter test mode.
The manual (SOS) switch indicator (green) will blink 3 times to indicate that test mode has been entered.
Speak into the telephone microphone assembly and confirm that your voice can be heard from the speakers, and then press the manual (SOS) switch for 3 seconds or less to enter test call mode.
If your voice cannot be heard from the speakers, press and hold the manual (SOS) switch for 3 to 10 seconds.
The manual (SOS) switch indicator (green) will blink 4 times.
Press the manual (SOS) switch and check that the manual (SOS) switch indicator (green) blinks 1 time. A test call will be performed and test data will be transmitted.
The manual (SOS) switch indicator (green) will illuminate for 10 seconds if test data transmission was successful.
The manual (SOS) switch indicator (red) will illuminate for 10 seconds if test data transmission fails.
DCM Operation History
This function is used to display operation history information and the time at which it was stored in the telematics transceiver.
Check DCM Operation History
When problem symptoms due to wave interference cannot be reproduced, this function provides telematics transceiver operation history information which can be used to explain the cause of the malfunction to the customer.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Telematics / Utility / DCM Operation History
| Tester Display |
|---|
| DCM Operation History |
| Item | Function | Parameter Name |
|---|---|---|
| Operation History | Displays the result of an attempt emergency call. | Success |
| Fail | ||
| Activation Failed | Displays the reason for failure if communication failed. | Unrecognized VIN |
| Unrecognized DCM-ID | ||
| Unrecognized IMSI | ||
| Unavailable Service Center | ||
| Service Already Activated | ||
| Backup Battery Status | Displays the mobilephone battery condition. | Low Battery Amount |
| Low Battery Voltage | ||
| Battery Exhaustion | ||
| Abnormal |
UNSENT EMERGENCY CALL DATA CLEAR
When an emergency call cannot be properly performed for an unspecified reason, the unsent data is recorded by the vehicle as "unsent emergency call data".
The unsent emergency call data can be cleared by performing the following procedure.
Clear the unsent emergency call data
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Telematics / Utility / Unsent Emergency Call Data Clear
| Tester Display |
|---|
| Unsent Emergency Call Data Clear |
According to the display on the GTS, clear the unsent emergency call data.