Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _060168 TELEMATICS _0296504 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1570  Red LED Error  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (red) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the engine switch is turned on (IG).

If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1570 Red LED Error Current for the manual (SOS) switch indicator (red) exceeds malfunction threshold for 20 seconds when the engine switch is on (IG).
·

Telematics transceiver

·

Map light assembly (manual (SOS) switch)

·

Wire harness or connector



WIRING DIAGRAM

E342832E23
1.896,1.021 2.354,1.219 0.458,0.198 10 false RED 3.396,0.656 3.656,0.958 0.26,0.302 10 false 22 3.406,1.073 3.604,1.313 0.198,0.24 10 false 19 3,0.656 3.615,0.854 0.615,0.198 10 false IND1 2.938,1.073 3.552,1.271 0.615,0.198 10 false GND3 1.24,1.729 1.698,1.927 0.458,0.198 10 false S1 1.24,1.906 3.958,2.135 2.719,0.229 10 false Map Light Assembly (Manual (SOS) Switch) 4.938,0.667 5.25,0.865 0.313,0.198 10 false 11 4.927,1.073 5.24,1.271 0.313,0.198 10 false 26 5.167,0.781 5.781,0.979 0.615,0.198 10 false IND1 5.167,1.073 5.781,1.271 0.615,0.198 10 false SIG- 5.104,1.729 5.563,1.927 0.458,0.198 10 false F140 5.115,1.917 6.677,2.125 1.563,0.208 10 false Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


HINT:

If DTC B1570 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.


PROCEDURE

1.CHECK DTC
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)
a.
B361013C08
0.594,1.604 1.083,1.271 false 1.042,1.802 1.438,1.26 false 0.865,1.833 1.438,2.042 0.573,0.208 10 false GND3 0.396,1.625 0.969,1.833 0.573,0.208 10 false IND1 0.146,0.167 0.719,0.375 0.573,0.208 10 false *a
*a Component with harness connected
(Map Light Assembly (Manual (SOS) Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
22 (IND1) - 19 (GND3) 2 seconds after engine switch turned on (IG)
→ Engine switch off
8.5 to 10 V
→ Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)

NG

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)
a.
B361012C07
0.49,1.813 0.646,1.344 false 1.5,1.802 1.302,1.333 false 0.125,0.115 0.438,0.271 0.313,0.156 10 false *a 1.344,1.844 1.958,2.042 0.615,0.198 10 false GND3 0.292,1.833 0.906,2.031 0.615,0.198 10 false IND1
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from the batteries to terminal 22 (IND1) and a negative (-) lead to terminal 19 (GND3) of the map light assembly (manual (SOS) switch) connector.


d.

Check if the manual (SOS) switch indicator (red) illuminates.

OK:

Manual (SOS) switch indicator (red) illuminates.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the F140 telematics transceiver connector.


b.

Disconnect the S1 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F140-11 (IND1) - S1-22 (IND1) Always Below 1 Ω
F140-11 (IND1) or S1-22 (IND1) - Body ground Always 10 kΩ or higher
F140-26 (SIG-) - S1-19 (GND3) Always Below 1 Ω
F140-26 (SIG-) or S1-19 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT