This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (green) circuit of the manual (SOS) switch.
The manual (SOS) switch indicator (green) illuminates after the engine switch is turned on (IG).
If the telematics system is not active, the manual (SOS) switch indicator (green) will turn off.
If the telematics system is active, the manual (SOS) switch indicator (green) will blink while communicating with the call center.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1571 | Green LED Error | Current for the manual (SOS) switch indicator (green) exceeds malfunction threshold for 20 seconds when the engine switch is on (IG). | ·
Telematics transceiver ·
Map light assembly (manual (SOS) switch) ·
Wire harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Component with harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 21 (IND2) - 19 (GND3) | 2 seconds after engine switch turned on (IG)
→ Engine switch off |
8.5 to 10 V
→ Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Remove the map light assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect 2 dry-cell batteries (1.5 V each) in series.
Connect a positive (+) lead from batteries to terminal 21 (IND2) and a negative (-) lead to terminal 19 (GND3) of the map light assembly (manual (SOS) switch) connector.
Check if the manual (SOS) switch indicator (green) comes on.
Manual (SOS) switch indicator (green) illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F140 telematics transceiver connector.
Disconnect the S1 map light assembly (manual (SOS) switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F140-12 (IND2) - S1-21 (IND2) | Always | Below 1 Ω |
| F140-12 (IND2) or S1-21 (IND2) - Body ground | Always | 10 kΩ or higher |
| F140-26 (SIG-) - S1-19 (GND3) | Always | Below 1 Ω |
| F140-26 (SIG-) or S1-19 (GND3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT