Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _060168 TELEMATICS _0296504 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1572  Microphone Error  


DESCRIPTION

This DTC is stored when a microphone signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1572 Microphone Error Current at terminal MCVD exceeds the malfunction threshold for 20 seconds while the engine switch is on (IG).
·

Telematics transceiver

·

Map light assembly (telephone microphone assembly)

·

Wire harness or connector



WIRING DIAGRAM

E342822E14
0.792,0.594 1.406,0.792 0.615,0.198 10 false MACC 0.823,1.052 1.281,1.26 0.458,0.208 10 false MCO+ 0.844,1.542 1.292,1.74 0.448,0.198 10 false MCO- 1.323,0.49 1.635,0.688 0.313,0.198 10 false 3 1.333,0.948 1.646,1.146 0.313,0.198 10 false 2 1.344,1.427 1.656,1.625 0.313,0.198 10 false 4 5.625,0.479 5.938,0.677 0.313,0.198 10 false 33 5.625,0.958 5.938,1.156 0.313,0.198 10 false 34 5.625,1.427 5.938,1.625 0.313,0.198 10 false 35 5.625,1.917 5.938,2.115 0.313,0.198 10 false 32 5.938,0.583 6.552,0.781 0.615,0.198 10 false MCVD 5.948,1.063 6.563,1.26 0.615,0.198 10 false MCI+ 5.958,1.521 6.573,1.719 0.615,0.198 10 false MCI- 5.958,2.021 6.573,2.219 0.615,0.198 10 false SGND 0.458,2.531 0.771,2.729 0.313,0.198 10 false S1 0.469,2.719 3.948,2.958 3.479,0.24 10 false Map Light Assembly (Telephone Microphone Assembly) 5.875,2.531 6.448,2.75 0.573,0.219 10 false F140 5.885,2.719 6.604,3.073 0.719,0.354 10 false Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TELEMATICS TRANSCEIVER
2.INSPECT TELEMATICS TRANSCEIVER
a.
B235166C59
0.917,1.656 1.292,1.281 false 1.313,1.833 1.458,1.281 false 0.104,0.094 0.375,0.354 0.271,0.26 10 false *a 0.938,1.854 1.427,2.021 0.49,0.167 10 false MCVD 0.615,1.646 1.104,1.854 0.49,0.208 10 false MCI-
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
33 (MCVD) - Body ground Engine switch on (ACC) 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition
35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

5.REPLACE TELEMATICS TRANSCEIVER
3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F140 telematics transceiver connector.


b.

Disconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F140-33 (MCVD) - S1-3 (MACC) Always Below 1 Ω
F140-34 (MCI+) - S1-2 (MCO+) Always Below 1 Ω
F140-35 (MCI-) - S1-4 (MCO-) Always Below 1 Ω
F140-33 (MCVD) or S1-3 (MACC) - Body ground Always 10 kΩ or higher
F140-34 (MCI+) or S1-2 (MCO+) - Body ground Always 10 kΩ or higher
F140-35 (MCI-) or S1-4 (MCO-) - Body ground Always 10 kΩ or higher
F140-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
B361012C09
2.406,0.354 2.229,0.969 false 2.01,0.969 1.802,0.354 false 0.125,0.115 0.438,0.271 0.313,0.156 10 false *a 2.365,0.156 2.979,0.354 0.615,0.198 10 false MACC 1.51,0.167 2.125,0.365 0.615,0.198 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (MACC) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE MAP LIGHT ASSEMBLY

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT