Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _060168 TELEMATICS _0296504 TELEMATICS SYSTEM J

TELEMATICS  TELEMATICS SYSTEM  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E342826E13
1.24,1.74 1.698,1.938 0.458,0.198 10 false S1 1.24,1.917 4,2.146 2.76,0.229 10 false Map Light Assembly (Manual (SOS) Switch) 5.125,1.729 5.583,1.927 0.458,0.198 10 false F140 5.135,1.906 6.646,2.156 1.51,0.25 10 false Telematics Transceiver 2.969,0.656 3.583,0.854 0.615,0.198 10 false RRID 2.938,1.073 3.552,1.271 0.615,0.198 10 false GND3 5.167,0.771 5.781,0.969 0.615,0.198 10 false SLED 5.167,1.094 5.781,1.292 0.615,0.198 10 false SIG- 3.417,0.656 3.604,0.854 0.188,0.198 10 false 20 4.958,0.656 5.115,0.854 0.156,0.198 10 false 9 3.427,1.063 3.604,1.25 0.177,0.188 10 false 19 4.917,1.083 5.25,1.25 0.333,0.167 10 false 26

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
a.
B361012C11
0.781,1.813 1.042,1.313 false 1.469,1.802 1.271,1.333 false 0.125,0.115 0.438,0.271 0.313,0.156 10 false *a 1.344,1.844 1.958,2.042 0.615,0.198 10 false GND3 0.5,1.833 1.115,2.031 0.615,0.198 10 false RRID
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect 4 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) from the batteries lead to terminal 20 (RRID) and a negative (-) lead to terminal 19 (GND3) of the map light assembly (manual (SOS) switch) connector.


d.

Check if the manual (SOS) switch illuminates.

OK:

Manual (SOS) switch illuminates.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the F140 telematics transceiver connector.


b.

Disconnect the S1 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F140-9 (SLED) - S1-20 (RRID) Always Below 1 Ω
F140-26 (SIG-) - S1-19 (GND3) Always Below 1 Ω
F140-9 (SLED) or S1-20 (RRID) - Body ground Always 10 kΩ or higher
F140-26 (SIG-) or S1-19 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR