Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
71052A
1.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY
Engage 6 hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.
71849
2.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps.
82167
3.INSTALL NO. 1 SEAT WIRE (w/ Seat Heater System)
Engage each claw and each clamp to install the No. 1 seat wire.
72201B
4.INSTALL SEAT TRACK ADJUSTING HANDLE
Engage the 2 springs to install the seat track adjusting handle.
71538B
5.INSTALL LH SEAT FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side)
Engage the 3 claws and guide to install the LH seat front seat cushion edge protector LH.
71537C
6.INSTALL LH SEAT FRONT SEAT CUSHION EDGE PROTECTOR RH (for Driver Side)
Use the same procedure as for the LH side.
71538A
7.INSTALL RH SEAT FRONT SEAT CUSHION EDGE PROTECTOR LH (for Front Passenger Side)
Engage the 3 claws and guide to install the RH seat front seat cushion edge protector LH.
71537C
8.INSTALL RH SEAT FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side)
Use the same procedure as for the LH side.
71874
9.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)
Engage the clip to install the front seat lower cushion shield LH.
Engage the hook as shown in the illustration.
Install the screw.
71873
10.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)
Use the same procedure as for the LH side.
73905
11.INSTALL FRONT SEAT AIRBAG SUB-ASSEMBLY RH (for Front Passenger Side)
w/ Front Seat Airbag Sub-assembly RH
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SRS SEAT CUSHION AIRBAG ASSEMBLY>INSTALLATION
87510K
12.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
71072S
13.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
14.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Driver Side)
Engage the 13 hooks to install the separate type front seat cushion cover with pad.
15.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Front Passenger Side)
Engage the 11 hooks to install the separate type front seat cushion cover with pad.
Engage the claw to install the connector.
w/ Seat Heater System:
Engage the 3 clamps.
71759B
16.INSTALL FRONT SEATBACK HOOK
Install the 2 front seatback hooks to the front seatback spring sub-assembly.
71054S
17.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY
Engage the 2 guides to install the front seatback spring sub-assembly to the front seatback frame sub-assembly.
Engage the 2 claws.
71587B
18.INSTALL FRONT SEATBACK EDGE PROTECTOR
Engage each claw to install the 2 front seatback edge protectors.
73920A
19.INSTALL FRONT SEAT AIRBAG ASSEMBLY
87510M
20.INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
71074S
21.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 4 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
22.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad.
71930A
23.INSTALL FRONT SEAT HEADREST SUPPORT ASSEMBLY
Engage each claw to install the 2 front seat headrest support assemblies.
| *a | Bracket |
Engage the 3 brackets and install the 2 nuts.
For vehicles with a front seat airbag assembly, the separate type front seatback cover with pad must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
Make sure that the strap is not twisted after installing the nut.
Install the brackets securely.
Return the separate type front seatback cover to its original position.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 3 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 5 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
24.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Engage the 4 guides to install the separate type front seatback assembly to the separate type front seat cushion assembly.
Install the 4 bolts.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
|
Seat Clamp |
Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.
Install the front seat airbag assembly wire harness to the seat clamp.
|
Fastener |
Engage the fastener to secure the front seat airbag assembly wire harness.
Engage the 2 hooks.
89178A
25.INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)
73240
26.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
73230
27.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
71862
28.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side)
Engage the claw and guide to install the front seat inner cushion shield.
Engage the claw and 3 guides.
71861
29.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)
Engage the claw and guide to install the front seat inner cushion shield.
Engage the claw and 4 guides.
71812D
30.INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side)
Engage the claw, guide and 2 clips to install the front seat cushion shield.
Engage the claw and 3 guides.
71811D
31.INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side)
Engage the claw, guide and 2 clips to install the front seat cushion shield.
Engage the claw and 4 guides.
72495
32.INSTALL VERTICAL ADJUSTING HANDLE (for Driver Side)
Install the vertical adjusting handle with the screw.
72526
33.INSTALL RECLINING ADJUSTER RELEASE HANDLE
Engage the claw to install the reclining adjuster release handle.
71074S
34.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.
87501A
35.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)