CLEARANCE WARNING ECU ASSEMBLY
Disconnect the F87 clearance warning ECU assembly connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F87-12 (IG) - F87-27 (E) | R - W-B | IG power source signal | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| F87-27 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| F87-38 (CLSW) - F87-27 (E) | GR - W-B | Back sonar or clearance sonar switch assembly power source signal | ·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly off |
Below 1 V |
·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on |
11 to 14 V |
Reconnect the F87 clearance warning ECU assembly connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F87-1 (S1) - F87-2 (E1) | B - W | Sensor communication signal (Rear right sensor) | ·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in R |
Pulse generation
(See waveform 1) |
| F87-2 (E1) - F87-27 (E) | W - W-B | Ground for sensor (Rear right sensor) | Always | Below 1 V |
| F87-3 (S2) - F87-2 (E1) | G - W | Sensor communication signal (Rear left sensor) | ·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in R |
Pulse generation
(See waveform 1) |
| F87-6 (S3) - F87-2 (E1) | R - W | Sensor communication signal (Rear right center sensor) | ·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in R |
Pulse generation
(See waveform 1) |
| F87-8 (S4) - F87-2 (E1) | Y - W | Sensor communication signal (Rear left center sensor) | ·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in R |
Pulse generation
(See waveform 1) |
| F87-11 (CBZ) - F87-10 (EF) | SB - LG | Clearance warning buzzer signal | Buzzer sounding | Pulse generation
(See waveform 2) |
| F87-19 (S5) - F87-20 (E5) | LG - SB | Sensor communication signal (Front right sensor) | ·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in R |
Pulse generation
(See waveform 1) |
·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in any position other than P or R ·
Less than approximately 10 km/h (6 mph) |
||||
| F87-20 (E5) - F87-27 (E) | SB - W-B | Ground for sensor (Front right sensor) | Always | Below 1 V |
| F87-21 (S6) - F87-22 (E6) | GR - SB | Sensor communication signal (Front left sensor) | ·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in R |
Pulse generation
(See waveform 1) |
·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in any position other than P or R ·
Less than approximately 10 km/h (6 mph) |
||||
| F87-22 (E6) - F87-27 (E) | SB - W-B | Ground for sensor (Front left sensor) | Always | Below 1 V |
Using an oscilloscope, check waveform 1.
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Terminal No. (Symbol) | F87-19 (S5) - F87-20 (E5)
F87-21 (S6) - F87-22 (E6) |
| Tool Setting | 2 V/DIV., 100 μs./DIV. |
| Condition | ·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in R |
·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in any position other than P or R ·
Less than approximately 10 km/h (6 mph) |
| Item | Content |
|---|---|
| Terminal No. (Symbol) | F87-1 (S1) - F87-2 (E1)
F87-3 (S2) - F87-2 (E1) F87-6 (S3) - F87-2 (E1) F87-8 (S4) - F87-2 (E1) |
| Tool Setting | 2 V/DIV., 100 μsec./DIV. |
| Condition | ·
Ignition switch ON ·
Back sonar or clearance sonar switch assembly on ·
Shift lever in R |
Using an oscilloscope, check waveform 2.
Waveform 2 (Reference)
| Item | Content |
|---|---|
| Terminal No. (Symbol) | F87-11 (CBZ) - F87-10 (EF) |
| Tool Setting | 2 V/DIV., 100 μsec./DIV. |
| Condition | Buzzer sounding |
The amplitude of the waveform changes according to the set volume.