Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT › 2016.11–2018.09
RM3160E _52 Drivetrain _060164 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0298229 AUTOMATIC TRANSAXLE UNIT A

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

Check bearing position and installation direction.

C362613N01
1.865,4.958 2.021,5.156 0.156,0.198 10 false A 3.729,6.094 3.885,6.292 0.156,0.198 10 false B 5.646,6.885 5.802,7.083 0.156,0.198 10 false C 1.625,7.792 1.781,7.99 0.156,0.198 10 false D

C362614N01
2.604,2.948 2.76,3.146 0.156,0.198 10 false E 3.74,3.813 3.896,4.01 0.156,0.198 10 false F 5.083,4.74 5.24,4.938 0.156,0.198 10 false G

Thrust Needle Roller Bearing and Bearing Race Diameter:
Mark Front Side Thrust Bearing Race Diameter Inside / Outside
mm (in.)
Thrust Bearing Diameter Inside / Outside
mm (in.)
Rear Side Thrust Bearing Race Diameter Inside / Outside
mm (in.)
A 32.6 (1.28) / 54.2 (2.13) 31.7 (1.25) / 52.3 (2.06) 31.7 (1.25) / 52.3 (2.06)
B 59.8 (2.35) / 77.0 (3.03) 58.3 (2.30) / 75.0 (2.95) -
C - 39.2 (1.54) / 52.6 (2.07) 38.1 (1.50) / 50.2 (1.98)
D - 33.3 (1.31) / 46.3 (1.82) 34.2 (1.35) / 47.3 (1.86)
E 34.4 (1.35) / 48.7 (1.92) 33.2 (1.31) / 47.7 (1.88) 33.2 (1.31) / 47.7 (1.88)
F 25.58 (1.01) / 43.7 (1.72) 24.2 (0.953) / 43.7 (1.72) 24.2 (0.953) / 43.7 (1.72)
G - 50.5 (1.99) / 74.5 (2.93) 52.8 (2.08) / 76.4 (3.01)


Hide 35101E 2.INSTALL AUTOMATIC TRANSMISSION CASE STRAIGHT PIN

NOTICE:

It is not necessary to remove the automatic transmission case straight pins unless they are being replaced.


HINT:
C362609C02
1.521,0.458 1.885,0.198 true 1,1.49 1.385,1.979 true 1.448,1.938 1.667,2.146 0.219,0.208 10 true *a 1.938,0.094 2.177,0.302 0.24,0.208 10 true *b
*a TMC Made
*b AW Made


TMC (TOYOTA) Made and AW (AISIN AW) Made components can be identified by the differing locations where the serial number is stamped.


a.
C365915C01
0.958,0.156 1.292,0.438 0.333,0.281 12 false *A 2.125,0.156 2.458,0.385 0.333,0.229 12 false *B
*A TMC Made
*B AW Made


Using a plastic hammer, tap in 2 new automatic transmission case straight pins to the specified protrusion height.

Protrusion Height:
for TMC Made:

7.0 to 8.0 mm (0.276 to 0.315 in.)

for AW Made:

10.7 to 11.3 mm (0.421 to 0.445 in.)



Hide 41206A 3.INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING (INNER RACE)

a.
C362543N01
1.667,1.74 1.115,1.615 false 1.604,2.094 1.052,1.969 false 0.813,1.542 1.271,1.74 0.458,0.198 10 false SST 0.74,1.896 1.198,2.094 0.458,0.198 10 false SST

Using SST and a press, install a new counter driven gear front tapered roller bearing (inner race) to the pinion and counter driven gear sub-assembly.

SST
09950-60010  (09951-00550)
09950-70010  (09951-07150)

NOTICE:

Be sure to install the counter driven gear front tapered roller bearing (inner race) so that there is no clearance between the counter driven gear front tapered roller bearing (inner race) and the pinion and counter driven gear sub-assembly. If there is any clearance, the turning torque of the pinion and counter driven gear sub-assembly cannot be measured correctly.



Hide 41206A 4.INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING (OUTER RACE)

a.
C362541N01
1.865,1.073 1.323,0.958 false 1.74,1.521 1.198,1.406 true 1,0.875 1.458,1.073 0.458,0.198 10 false SST 0.875,1.323 1.333,1.521 0.458,0.198 10 false SST

Using SST and a hammer, install a new counter driven gear front tapered roller bearing (outer race) and pinion and counter driven gear shim to the transaxle housing.

SST
09950-60020  (09951-00780)
09950-70010  (09951-07150)

NOTICE:

Be sure to install the counter driven gear front tapered roller bearing (outer race) so that there is no clearance between the counter driven gear front tapered roller bearing (outer race), pinion and counter driven gear shim and the transaxle housing. If there is any clearance, the turning torque of the pinion and counter driven gear sub-assembly cannot be measured correctly.



Hide 41206A 5.INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING (INNER RACE)

a.
C365916N01
0.719,1.24 1.323,1.396 false 0.625,1.729 1.229,1.885 false 0.625,2.313 1.219,2.115 true 0.396,1.094 0.854,1.292 0.458,0.198 10 false SST 0.271,1.615 0.729,1.813 0.458,0.198 10 false SST 0.271,2.281 0.729,2.479 0.458,0.198 10 false SST

Using SST and a press, install a new counter driven gear rear tapered roller bearing (inner race) to the pinion and counter driven gear sub-assembly.

SST
09506-30012  
09950-60010  (09951-00420, 09951-00550)
09950-70010  (09951-07150)

NOTICE:

Be sure to install the counter driven gear rear tapered roller bearing (inner race) so that there is no clearance between the counter driven gear rear tapered roller bearing (inner race) and the pinion and counter driven gear sub-assembly. If there is any clearance, the turning torque of the pinion and counter driven gear sub-assembly cannot be measured correctly.



Hide 41206A 6.INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING (OUTER RACE)

a.
C362535N01
1.792,1.802 2.646,1.667 true 0.729,2.552 1.594,2.188 true 2.719,1.583 3.177,1.781 0.458,0.198 10 false SST 0.406,2.479 0.865,2.677 0.458,0.198 10 false SST

Using SST and a hammer, install a new counter driven gear rear tapered roller bearing (outer race) to the automatic transaxle case sub-assembly.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)

NOTICE:

Be sure to install the counter driven gear rear tapered roller bearing (outer race) so that there is no clearance between the counter driven gear rear tapered roller bearing (outer race) and the automatic transaxle case sub-assembly. If there is any clearance, the turning torque of the pinion and counter driven gear sub-assembly cannot be measured correctly.



Hide 7.ADJUST FRONT DIFFERENTIAL CASE TAPERED ROLLER BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and automatic transaxle case sub-assembly.


b.

Coat the front differential case front tapered roller bearing (inner race) and the front differential case rear tapered roller bearing (inner race) with a sufficient amount of Toyota Genuine ATF WS.


c.
C365899

Install the differential case assembly to the automatic transaxle case sub-assembly.


d.
C362561N01
1.427,0.365 1.594,0.521 0.167,0.156 10 false A 1.188,0.365 1.354,0.542 0.167,0.177 10 false B 1.917,0.417 2.083,0.573 0.167,0.156 10 false A 2.146,0.469 2.313,0.625 0.167,0.156 10 true A 2.917,0.729 3.083,0.885 0.167,0.156 10 true A 3.094,1.063 3.26,1.219 0.167,0.156 10 true A 3.167,1.969 3.333,2.125 0.167,0.156 10 true A 3.021,2.688 3.188,2.844 0.167,0.156 10 true A 2.271,2.865 2.438,3.021 0.167,0.156 10 true A 1.958,2.885 2.125,3.042 0.167,0.156 10 true A 0.719,0.625 0.885,0.802 0.167,0.177 10 false B 0.531,0.802 0.698,0.979 0.167,0.177 10 false B 0.208,1.26 0.375,1.438 0.167,0.177 10 false B 0.104,1.615 0.271,1.792 0.167,0.177 10 false B 0.083,1.885 0.25,2.063 0.167,0.177 10 false B 0.271,2.448 0.438,2.625 0.167,0.177 10 false B 0.458,2.677 0.625,2.854 0.167,0.177 10 false B 1.021,2.875 1.188,3.052 0.167,0.177 10 false B 1.323,2.885 1.49,3.063 0.167,0.177 10 false B 2.448,0.604 2.615,0.781 0.167,0.177 10 true B 1.625,2.896 1.792,3.073 0.167,0.177 10 false B

Install the transaxle housing to the automatic transaxle case sub-assembly with the 21 bolts (A and B).

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

Bolt Length:
Bolt (A) Bolt (B)
40 mm (1.57 in.) 35 mm (1.38 in.)



e.
C362554N01
0.448,1.219 0.979,1.396 true 0.125,1.125 0.583,1.323 0.458,0.198 10 false SST

Using SST, rotate the differential case assembly 20 times or more to stabilize the bearing.

SST
09564-33010  


f.
C362556N01
0.427,1.26 0.927,1.354 true 0.115,1.188 0.573,1.385 0.458,0.198 10 false SST

Using SST and a torque wrench, measure the turning torque of the front differential case tapered roller bearing while rotating SST at 10 rpm.

SST
09564-33010  

Standard Turning Torque:

0.69 to 1.02 N*m (8 to 10 kgf*cm, 7 to 9 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Differential Drive Pinion Shim Thickness:
Part Number Thickness
mm (in.)
Mark
90564-75002 1.10 (0.0433) 50
90564-75003 1.13 (0.0445) 51
90564-75004 1.16 (0.0457) 52
90564-75005 1.19 (0.0469) 53
90564-75006 1.22 (0.0480) 54
90564-75007 1.25 (0.0492) 55
90564-75008 1.28 (0.0504) 56
90564-75009 1.31 (0.0516) 57
90564-75010 1.34 (0.0528) 58
90564-75011 1.37 (0.0539) 59
90564-75012 1.40 (0.0551) 60
90564-75013 1.43 (0.0563) 61
90564-75014 1.46 (0.0575) 62
90564-75015 1.49 (0.0587) 63
90564-75016 1.52 (0.0598) 64
90564-75017 1.55 (0.0610) 65
90564-75018 1.58 (0.0622) 66
90564-75019 1.61 (0.0634) 67
90564-75023 1.64 (0.0646) 68
90564-75024 1.67 (0.0657) 69
90564-75025 1.70 (0.0669) 70
90564-75026 1.73 (0.0681) 71
90564-75027 1.76 (0.0693) 72
90564-75028 1.79 (0.0705) 73
90564-75029 1.82 (0.0717) 74
90564-75030 1.85 (0.0728) 75
90564-75031 1.88 (0.0740) 76
90564-75032 1.91 (0.0752) 77
90564-75033 1.94 (0.0764) 78
90564-75034 1.97 (0.0776) 79
90564-75035 2.00 (0.0787) 80



g.

Remove the 21 bolts and transaxle housing from the automatic transaxle case sub-assembly.


Hide 8.ADJUST PINION AND COUNTER DRIVEN GEAR TAPERED ROLLER BEARING PRELOAD

a.

Coat the counter driven gear front tapered roller bearing (inner race) and the counter driven gear rear tapered roller bearing (inner race) with a sufficient amount of Toyota Genuine ATF WS.


b.
C365900

Install the pinion and counter driven gear sub-assembly to the automatic transaxle case sub-assembly.


c.
C362561N01
1.427,0.365 1.594,0.521 0.167,0.156 10 false A 1.188,0.365 1.354,0.542 0.167,0.177 10 false B 1.917,0.417 2.083,0.573 0.167,0.156 10 false A 2.146,0.469 2.313,0.625 0.167,0.156 10 true A 2.917,0.729 3.083,0.885 0.167,0.156 10 true A 3.094,1.063 3.26,1.219 0.167,0.156 10 true A 3.167,1.969 3.333,2.125 0.167,0.156 10 true A 3.021,2.688 3.188,2.844 0.167,0.156 10 true A 2.271,2.865 2.438,3.021 0.167,0.156 10 true A 1.958,2.885 2.125,3.042 0.167,0.156 10 true A 0.719,0.625 0.885,0.802 0.167,0.177 10 false B 0.531,0.802 0.698,0.979 0.167,0.177 10 false B 0.208,1.26 0.375,1.438 0.167,0.177 10 false B 0.104,1.615 0.271,1.792 0.167,0.177 10 false B 0.083,1.885 0.25,2.063 0.167,0.177 10 false B 0.271,2.448 0.438,2.625 0.167,0.177 10 false B 0.458,2.677 0.625,2.854 0.167,0.177 10 false B 1.021,2.875 1.188,3.052 0.167,0.177 10 false B 1.323,2.885 1.49,3.063 0.167,0.177 10 false B 2.448,0.604 2.615,0.781 0.167,0.177 10 true B 1.625,2.896 1.792,3.073 0.167,0.177 10 false B

Install the transaxle housing to the automatic transaxle case sub-assembly with the 21 bolts (A and B).

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

Bolt Length:
Bolt (A) Bolt (B)
40 mm (1.57 in.) 35 mm (1.38 in.)



d.
C362554N01
0.448,1.219 0.979,1.396 true 0.125,1.125 0.583,1.323 0.458,0.198 10 false SST

Using SST, rotate the differential case assembly 20 times or more to stabilize the bearing.

SST
09564-33010  


e.
C362556N01
0.427,1.26 0.927,1.354 true 0.115,1.188 0.573,1.385 0.458,0.198 10 false SST

Using SST and a torque wrench, measure the turning torque of the pinion and counter driven gear tapered roller bearing while rotating SST at 10 rpm.

SST
09564-33010  

Standard Turning Torque:

Front differential case tapered roller bearing preload + 0.99 to 2.26 N*m (11 to 23 kgf*cm, 9 to 20 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Pinion and Counter Driven Gear Shim Thickness:
Part Number Thickness
mm (in.)
Mark
90564-67047 1.19 (0.0469) AA
90564-67048 1.22 (0.0480) AB
90564-67049 1.25 (0.0492) AC
90564-67050 1.28 (0.0504) AD
90564-67051 1.31 (0.0516) AE
90564-67052 1.34 (0.0528) AF
90564-67053 1.37 (0.0539) AG
90564-67054 1.40 (0.0551) AH
90564-67055 1.43 (0.0563) AJ
90564-67056 1.46 (0.0575) AK
90564-67057 1.49 (0.0587) AL
90564-67058 1.52 (0.0598) AM
90564-67059 1.55 (0.0610) AN
90564-67060 1.58 (0.0622) AP
90564-67061 1.61 (0.0634) AR
90564-67062 1.64 (0.0646) AS
90564-67063 1.67 (0.0657) AT
90564-67064 1.70 (0.0669) AU
90564-67065 1.73 (0.0681) AV
90564-67066 1.76 (0.0693) AW
90564-67067 1.79 (0.0705) AX
90564-67068 1.82 (0.0717) AY
90564-67069 1.85 (0.0728) AZ
90564-67071 1.88 (0.0740) BA
90564-67072 1.91 (0.0752) BB
90564-67073 1.94 (0.0764) BC
90564-67074 1.97 (0.0776) BD
90564-67075 2.00 (0.0787) BE
90564-67076 2.03 (0.0799) BF
90564-67077 2.06 (0.0811) BG
90564-67078 2.09 (0.0823) BH
90564-67079 2.12 (0.0835) BJ
90564-67080 2.15 (0.0846) BK
90564-67081 2.18 (0.0858) BL
90564-67082 2.21 (0.0870) BM



f.

Remove the 21 bolts and transaxle housing from the automatic transaxle case sub-assembly.


g.

Remove the pinion and counter driven gear sub-assembly from the automatic transaxle case sub-assembly.


h.

Remove the differential case assembly from the automatic transaxle case sub-assembly.


Hide 35104R 9.INSTALL NO. 2 TRANSAXLE CASE PLUG

a.

Clean the 6 No. 2 transaxle case plugs and 6 installation holes.


b.
C362559

Apply adhesive to 2 or 3 threads on the ends of the No. 2 transaxle case plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the No. 2 transaxle case plug immediately after applying adhesive to prevent foreign matter from attaching to them.



c.
C362547

Using a 6 mm socket hexagon wrench, install the 3 No. 2 transaxle case plugs and 3 new gaskets to the automatic transaxle case sub-assembly.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


d.
C362550

Using a 6 mm socket hexagon wrench, install the 3 No. 2 transaxle case plugs and 3 new gaskets to the transaxle housing.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 35104Q 10.INSTALL NO. 1 TRANSAXLE CASE PLUG

a.
C362546

Coat 8 new O-rings with Toyota Genuine ATF WS and install them to the 8 No. 1 transaxle case plugs.


b.
C362544

Install the 4 No. 1 transaxle case plugs to the automatic transaxle case sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


c.
C362545

Install the 4 No. 1 transaxle case plugs to the transaxle housing.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 35605C 11.INSTALL NEEDLE ROLLER BEARING

a.
C362532N01
2.427,1.417 2.885,1.073 true 2.51,1.719 2.938,1.26 true 2.958,0.969 3.333,1.156 0.375,0.188 10 false SST 3,1.188 3.375,1.375 0.375,0.188 10 false SST

Using SST and a press, install a new needle roller bearing to the transaxle housing.

SST
09550-60010  (09951-00560)
09950-70010  (09951-07200)

NOTICE:

Be careful not to damage the transaxle housing.



Hide 43420H 12.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C362530N01
1.448,1.385 1.813,1.563 false 2.042,2.5 2.604,2.76 true 1.146,1.313 1.604,1.51 0.458,0.198 10 false SST 2.667,2.698 3.125,2.896 0.458,0.198 10 false SST

Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle case sub-assembly.

SST
09649-17010  
09950-70010  (09951-07200)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 43410M 13.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C362528N01
1.563,1.792 1.948,1.635 false 0.74,2.542 1.313,2.375 true 2.021,1.542 2.479,1.74 0.458,0.198 10 false SST 0.427,2.469 0.885,2.667 0.458,0.198 10 false SST

Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

SST
09316-10010  
09950-70010  (09951-07200)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 14.INSTALL TRANSAXLE CASE OIL SEAL

a.

Clean and degrease the oil seal press-in surface.


b.
C362640E01
1.854,2.604 2.667,2.917 true 1.25,1.75 1.667,2.063 true 2.771,2.865 3.229,3.063 0.458,0.198 10 false SST 0.917,1.646 1.375,1.844 0.458,0.198 10 false SST

Using SST and a hammer, install a new transaxle case oil seal to the transaxle housing.

SST
09950-60010  (09951-00640)
09950-70010  (09951-07200)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



c.

Apply MP grease to the lip of the transaxle case oil seal.


Hide 15.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C362522N01
1.823,0.865 2.427,1.292 true 2.563,1.021 2.969,0.781 false 1.5,0.781 1.958,0.979 0.458,0.198 10 false SST 3.021,0.698 3.344,0.885 0.323,0.188 10 false SST

Using SST and a hammer, install a new manual valve lever shaft oil seal to the automatic transaxle case sub-assembly.

SST
09950-60010  (09951-00210)
09950-70010  (09951-07200)

Standard Depth:

-0.3 to 0.4 mm (-0.0118 to 0.0157 in.)



b.

Apply MP grease to the lip of the manual valve lever shaft oil seal.


Hide 41206A 16.INSTALL NEEDLE ROLLER BEARING

a.
C362518N01
1.854,1.167 2.969,0.375 true 1.042,2.802 1.771,1.792 true 3.031,0.292 3.354,0.521 0.323,0.229 10 false SST 0.729,2.729 1.052,2.958 0.323,0.229 10 false SST

Using SST and a press, install a new needle roller bearing to the automatic transaxle case sub-assembly.

SST
09950-60010  (09951-00210)
09950-70010  (09951-07150)

Standard Depth:

2.1 to 2.5 mm (0.0827 to 0.0984 in.)


NOTICE:

Install the needle roller bearing with its supplier name mark facing the front of the automatic transaxle assembly.



Hide 35623H 17.INSTALL 1ST AND REVERSE BRAKE PISTON

a.
C362514

Apply a light coat of Toyota Genuine ATF WS to 2 new O-rings and install them to the 1st and reverse brake piston.

NOTICE:
·

Make sure to correctly distinguish between the inner side and outer side O-rings.

·

Be careful not to damage or twist the O-rings.




b.
C362515C01
0.823,0.396 1.26,0.583 false 0.75,1.708 1.219,1.573 false 0.625,0.313 0.938,0.469 0.313,0.156 10 false *1 0.531,1.635 0.844,1.792 0.313,0.156 10 false *2
*1 1st And Reverse Brake Return Spring Sub-assembly
*2 1st And Reverse Brake Piston


Set the 1st and reverse brake return spring sub-assembly on the 1st and reverse brake piston.


c.
C362516

Install the 1st and reverse brake piston with 1st and reverse brake return spring sub-assembly to the automatic transaxle case sub-assembly.

NOTICE:

Make sure that the O-rings are not damaged or do not jump out of position during installation.



Hide 35068 18.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C362512C01
0.729,0.333 0.885,0.51 0.156,0.177 10 true *a
*a Snap ring opening within this area.


Set the snap ring on the automatic transaxle case sub-assembly as shown in the illustration.

NOTICE:

The opening of the snap ring should be within the area shown in the illustration (spline portion).



b.
C362509N01
1.969,0.99 2.813,0.604 true 0.531,0.531 1.635,1.313 true 2.875,0.531 3.333,0.729 0.458,0.198 10 false SST 0.219,0.448 0.677,0.646 0.458,0.198 10 false SST

Place SST on the 1st and reverse brake return spring sub-assembly and compress it with a press.

SST
09380-60011  (09381-06020, 09381-06050, 09381-06060, 09381-06100, 09381-06110)
09950-70010  (09951-07200)

NOTICE:

Stop the press when the 1st and reverse brake return spring sub-assembly is flush with the snap ring groove.



c.
C362510

Using a screwdriver with its tip wrapped with protective tape, install the snap ring into the snap ring groove of the automatic transaxle case sub-assembly.

NOTICE:
·

Be careful not to damage the automatic transaxle case sub-assembly.

·

Make sure that the snap ring is installed in the groove of the automatic transaxle case sub-assembly correctly.




Hide 35623P 19.INSTALL NO. 2 1ST AND REVERSE BRAKE PISTON

a.
C362508

Install the No. 2 1st and reverse brake piston to the automatic transaxle case sub-assembly.


Hide 35682 20.INSTALL 2ND BRAKE BRAKE DISC

a.
C362506C01
1.979,0.906 1.979,2.677 1.979,2.677 2.188,2.677 true 1.979,0.906 2.198,0.906 false 1.979,1.344 2.188,1.344 false 1.802,1.781 2.188,1.781 false 1.979,2.219 2.188,2.219 false 3.094,0.646 3.26,0.646 3.26,0.646 3.26,2.729 false 3.104,1.115 3.26,1.115 false 3.104,1.563 3.26,1.563 false 3.104,2 3.26,2 false 3.094,2.438 3.26,2.438 false 1.969,0.208 2.198,0.333 false 1.75,0.125 2.063,0.281 0.313,0.156 10 false *1 3.177,2.76 3.365,2.927 0.188,0.167 10 false *2 1.573,1.688 1.75,1.865 0.177,0.177 10 false *3 1,0.448 1.313,0.604 0.313,0.156 10 false *a 1.01,1.115 1.323,1.271 0.313,0.156 10 false *b
*1 2nd Brake Brake Flange
*2 2nd Brake Brake Disc
*3 2nd Brake Brake Plate
*a Snap Ring Side
*b 2nd Brake Brake Disc Side


Install the 5 2nd brake brake plates, 5 2nd brake brake discs and 2nd brake brake flange to the automatic transaxle case sub-assembly.

NOTICE:

Assemble the 2nd brake brake flange with its tapered surface facing toward the 2nd brake brake disc.



b.
C362507C01
0.604,1.583 0.781,1.76 0.177,0.177 10 true *a
*a Snap ring opening within this area.


Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the automatic transaxle case sub-assembly.

NOTICE:

The opening of the snap ring should be within the area shown in the illustration (spline portion).



Hide 35653B 22.INSTALL DIRECT CLUTCH DRUM OIL SEAL RING

a.

Apply a small amount of MP grease to the entire circumference of the direct clutch drum oil seal ring installation groove portion.

HINT:

By applying MP grease, the wobble within the direct clutch drum oil seal ring installation groove will be eliminated, preventing damage to the direct clutch drum oil seal ring at the time of front planetary gear assembly installation.



b.
C362503

Coat 2 new direct clutch drum oil seal rings with Toyota Genuine ATF WS and install them to the automatic transaxle case sub-assembly.

NOTICE:

While making the spread of the opening of the direct clutch drum oil seal ring as small as possible, install it to the automatic transaxle case sub-assembly. If the ring opening is spread, briefly hold it closed with your fingers to return it to its original condition.



Hide 35652E 23.INSTALL C-2 CLUTCH PISTON

a.
C362502

Apply a light coat of Toyota Genuine ATF WS to 2 new O-rings and install it to the intermediate shaft sub-assembly.

NOTICE:

Be careful not to damage or twist the O-ring.



b.

Apply a light coat of Toyota Genuine ATF WS to the lip seal of the C-2 clutch piston.


c.
C362501

Install the C-2 clutch piston to the intermediate shaft sub-assembly.

NOTICE:
·

Make sure the lip is not cut or folded.

·

Be careful not to damage the lip seal of the C-2 clutch piston.




Hide 35608N 24.INSTALL CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C362499

Install the clutch return spring sub-assembly to the intermediate shaft sub-assembly.


Hide 35698A 25.INSTALL C-2 CLUTCH BALANCER

a.

Apply a light coat of Toyota Genuine ATF WS to the lip seal of the C-2 clutch balancer.


b.
C362498

Install the C-2 clutch balancer to the intermediate shaft sub-assembly.

NOTICE:

Be careful not to damage the lip seal of the C-2 clutch balancer.


NOTICE:
·

Make sure the lip is not cut or folded.

·

Be careful not to damage the lip seal of the C-2 clutch balancer.




c.
C362497N01
0.427,0.677 0.573,0.51 false 2.406,1.698 2.969,1.281 false 0.115,0.615 0.458,0.792 0.344,0.177 10 false SST 2.083,1.625 2.427,1.802 0.344,0.177 10 false SST

Place SST on the C-2 clutch balancer and compress the clutch return spring sub-assembly with a press.

SST
09387-00020  

NOTICE:

Stop the press when the clutch return spring sub-assembly is flush with the snap ring groove.



d.

Using SST, install the snap ring to the intermediate shaft sub-assembly.

SST
09350-30020  (09350-07070)

NOTICE:

Make sure that the snap ring is installed in the groove of the intermediate shaft sub-assembly correctly.



Hide 35667B 26.INSTALL NO. 2 CLUTCH DISC

a.
C362496C01
1.875,2.583 1.875,0.979 1.875,0.979 2.042,0.979 false 2.042,1.51 1.698,1.51 false 2.052,2.583 1.875,2.583 false 2.052,2.052 1.875,2.052 false 3.302,2.698 3.302,0.74 3.302,0.74 3.135,0.74 false 3.302,1.26 3.125,1.26 false 3.302,1.813 3.135,1.813 false 3.302,2.333 3.135,2.333 false 2.115,0.271 1.885,0.188 false 1.677,0.094 1.875,0.281 0.198,0.188 10 false *1 3.219,2.719 3.406,2.896 0.188,0.177 10 false *2 1.5,1.417 1.813,1.573 0.313,0.156 10 false *3 1,0.365 1.313,0.521 0.313,0.156 10 false *a 1,1 1.313,1.156 0.313,0.156 10 false *b
*1 Direct Clutch Flange
*2 No. 2 Clutch Disc
*3 No. 2 Clutch Plate
*a Snap Ring Side
*b No. 2 Clutch Disc Side


Install the 4 No. 2 clutch plates, 4 No. 2 clutch discs and direct clutch flange to the intermediate shaft sub-assembly.

NOTICE:
·

Be careful during assembly because there are 2 types of No. 2 clutch plate with different thicknesses.

·

Assemble the direct clutch flange with its tapered surface facing toward the No. 2 clutch disc.




b.
C362495

Using a screwdriver with its tip wrapped in protective tape, install the snap ring to the intermediate shaft sub-assembly.

NOTICE:
·

Be careful not to damage the intermediate shaft sub-assembly.

·

Make sure that the snap ring is installed in the groove of the intermediate shaft sub-assembly correctly.




Hide 35786A 27.INSTALL NO. 1 THRUST BEARING RACE

a.
C362494

Coat the No. 1 thrust bearing race with Toyota Genuine ATF WS and install it to the automatic transaxle case sub-assembly.

No. 1 Thrust Bearing Race Diameter:
Inside Outside
52.8 mm (2.08 in.) 76.4 mm (3.01 in.)


NOTICE:

Securely insert the claw of the No. 1 thrust bearing race into the hole of the automatic transaxle case sub-assembly.



Hide 28.INSTALL THRUST NEEDLE ROLLER BEARING

a.
C362492

Coat the thrust needle roller bearing with Toyota Genuine ATF WS and install it to the C-2 clutch assembly.

Thrust Needle Roller Bearing Diameter:
Inside Outside
50.5 mm (1.99 in.) 74.5 mm (2.93 in.)


NOTICE:

Make sure to assemble the thrust needle roller bearing in the correct direction.


HINT:

When installing the C-2 clutch assembly, if the thrust needle roller bearing falls off, coat the C-2 clutch assembly installation surface with MP grease and install the parts.



Hide 29.INSTALL C-2 CLUTCH ASSEMBLY

a.
C362491

Install the C-2 clutch assembly to the automatic transaxle case sub-assembly.


Hide 35729B 31.INSTALL NO. 4 PLANETARY CARRIER THRUST WASHER

a.
C362479

Install the No. 4 planetary carrier thrust washer to the rear planetary gear assembly.

HINT:
·

Securely insert each protrusion of the No. 4 planetary carrier thrust washer into each indentation of the rear planetary gear assembly.

·

When installing the rear planetary gear assembly, if the No. 4 planetary carrier thrust washer falls off, coat the rear planetary gear assembly installation surface with MP grease and install the parts.




Hide 35760 32.INSTALL REAR PLANETARY GEAR ASSEMBLY

a.
C362477

Install the rear planetary gear assembly to the C-2 clutch assembly.


Hide 35787C 33.INSTALL NO. 2 THRUST BEARING RACE

a.
C362639

Coat the No. 2 thrust bearing race with Toyota Genuine ATF WS and install it to the C-2 clutch assembly.

No. 2 Thrust Bearing Race Diameter:
Inside Outside
24.2 mm (0.953 in.) 43.7 mm (1.72 in.)



Hide 34.INSTALL THRUST NEEDLE ROLLER BEARING

a.
C362638

Coat the thrust needle roller bearing with Toyota Genuine ATF WS and install it to the C-2 clutch assembly.

Thrust Needle Roller Bearing Diameter:
Inside Outside
24.2 mm (0.953 in.) 43.7 mm (1.72 in.)



Hide 35788D 35.INSTALL NO. 3 THRUST BEARING RACE

a.
C362487

Coat the No. 3 thrust bearing race with Toyota Genuine ATF WS and install it to the rear planetary sun gear sub-assembly.

No. 3 Thrust Bearing Race Diameter:
Inside Outside
25.58 mm (1.01 in.) 43.7 mm (1.72 in.)


HINT:

When installing the rear planetary sun gear sub-assembly, if the No. 3 thrust bearing race falls off, coat the rear planetary sun gear sub-assembly installation surface with MP grease and install the parts.



Hide 35707D 36.INSTALL REAR PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C362480

Install the rear planetary sun gear sub-assembly to the C-2 clutch assembly.


Hide 35789U 37.INSTALL THRUST BEARING RACE

a.
C362486

Coat the thrust bearing race with Toyota Genuine ATF WS and install it to the rear planetary sun gear sub-assembly.

Thrust Bearing Race Diameter:
Inside Outside
33.2 mm (1.31 in.) 47.7 mm (1.88 in.)



Hide 38.INSTALL THRUST NEEDLE ROLLER BEARING

a.
C362484

Coat the thrust needle roller bearing with Toyota Genuine ATF WS and install it to the rear planetary sun gear sub-assembly.

Thrust Needle Roller Bearing Diameter:
Inside Outside
33.2 mm (1.31 in.) 47.7 mm (1.88 in.)



Hide 35785B 39.INSTALL NO. 4 THRUST BEARING RACE

a.
C362482

Coat the No. 4 thrust bearing race with Toyota Genuine ATF WS and install it to the rear planetary sun gear sub-assembly.

No. 4 Thrust Bearing Race Diameter:
Inside Outside
34.4 mm (1.35 in.) 48.7 mm (1.92 in.)



Hide 35706V 40.INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C362476

Install the planetary sun gear sub assembly to the rear planetary gear assembly.


Hide 35739 41.INSTALL NO. 3 PLANETARY CARRIER THRUST WASHER

a.
C362475

Coat the No. 3 planetary carrier thrust washer with Toyota Genuine ATF WS and install it to the rear planetary gear assembly.

NOTICE:

Securely insert the claw of the No. 3 planetary carrier thrust washer into the hole of the rear planetary gear assembly.



Hide 35681C 42.INSTALL NO. 1 BRAKE DISC

a.
C362472C01
1.917,2.448 1.75,2.448 1.75,2.448 1.75,0.75 true 1.75,0.75 1.917,0.75 false 1.76,0.208 1.938,0.313 false 1.604,1.885 1.906,1.885 false 3.063,1.052 3.25,1.052 3.25,1.052 3.25,3.063 false 3.073,2.76 3.25,2.76 false 3.073,1.625 3.24,1.625 false 3.073,2.177 3.24,2.177 false 1.75,1.313 1.917,1.313 false 1.552,0.115 1.865,0.271 0.313,0.156 10 false *1 1.396,1.792 1.708,1.948 0.313,0.156 10 false *2 3.167,3.104 3.344,3.292 0.177,0.188 10 false *3 0.979,0.344 1.292,0.5 0.313,0.156 10 false *a 0.979,0.99 1.292,1.146 0.313,0.156 10 false *b
*1 No. 1 Brake Flange
*2 No. 1 Brake Disc
*3 No. 1 Brake Plate
*a Snap Ring Side
*b No. 1 Brake Disc Side


Install the 4 No. 1 brake plates, 4 No. 1 brake discs and No. 1 brake flange to the counter drive gear sub-assembly.

NOTICE:
·

Be careful during assembly because there are 2 types of No. 1 brake plate with different thicknesses.

·

Assemble the No. 1 brake flange with its tapered surface facing toward the No. 1 brake disc.




b.
C362473C01
0.615,2.646 0.927,2.802 0.313,0.156 10 false *a
*a Snap ring opening within this area.


Using a screwdriver with its tip wrapped in protective tape, install the snap ring to the counter drive gear sub-assembly.

NOTICE:
·

Be careful not to damage the counter drive gear sub-assembly.

·

Make sure that the snap ring is installed in the groove of the counter drive gear sub-assembly correctly.

·

The opening of the snap ring should be within the area shown in the illustration (spline portion).




Hide 35704C 43.INSTALL COUNTER DRIVE GEAR SUB-ASSEMBLY

a.

Clean and degrease the counter drive gear sub-assembly installation bolts and the 8 bolt holes.

NOTICE:

If the bolts are tightened without cleaning and degreasing the bolts and bolt holes, the tightening torque will be too high and the counter drive gear sub-assembly or automatic transaxle case sub-assembly may be damaged.



b.
C362470

Coat a new O-ring with Toyota Genuine ATF WS and install it to the automatic transaxle case sub-assembly.


c.
C362469

Install the counter drive gear sub-assembly together with the pinion and counter driven gear sub-assembly to the automatic transaxle case sub-assembly.


d.
C362468C02
1.625,0.094 1.792,0.281 0.167,0.188 10 true *a 1.385,0.146 1.563,0.313 0.177,0.167 10 true *b 2.417,0.354 2.615,0.542 0.198,0.188 10 true *a 2.427,1.802 2.604,1.969 0.177,0.167 10 true *b 1.865,2.01 2.052,2.177 0.188,0.167 10 true *b 1.385,2 1.542,2.167 0.156,0.167 10 true *b 1.167,1.969 1.323,2.135 0.156,0.167 10 true *b 0.969,1.792 1.125,1.958 0.156,0.167 10 true *b
*a Bolt A
*b Bolt B


Temporarily install the 8 bolts (A and B).

HINT:

Bolt (A) is a hexagon socket head cap bolt.



e.

Fully tighten the 6 bolts (B).

Torque:
76 N*m (775 kgf*cm, 56 ft.*lbf)


f.

Using a T50 "TORX" socket wrench, fully tighten the 2 bolts (A).

Torque:
31.8 N*m (324 kgf*cm, 23 ft.*lbf)


Hide 35598 45.INSTALL PARKING LOCK SLEEVE

a.
C362466

Coat the parking lock sleeve with Toyota Genuine ATF WS and install it to the automatic transaxle case sub-assembly.


Hide 35557 46.INSTALL PARKING LOCK PAWL

a.
C362465

Coat the parking lock pawl with Toyota Genuine ATF WS and install it to the automatic transaxle case sub-assembly.


Hide 35556 47.INSTALL PARKING LOCK PAWL SHAFT

a.
C362464

Coat the parking lock pawl shaft with Toyota Genuine ATF WS and install it to the automatic transaxle case sub-assembly.


Hide 35557A 48.INSTALL PARKING LOCK PAWL TORSION SPRING

a.
C362463

Install the parking lock pawl torsion spring to the automatic transaxle case sub-assembly as shown in the illustration.

NOTICE:

Securely insert the parking lock pawl torsion spring all the way into the parking lock pawl shaft.



Hide 35506 49.INSTALL MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C362462

Install the manual valve lever shaft sub-assembly to the automatic transaxle case sub-assembly.

NOTICE:

When installing the manual valve lever shaft sub-assembly, be careful not to damage the manual valve lever shaft oil seal.



Hide 35501 50.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
C365918C01
2.802,0.49 2.708,0.365 2.708,0.365 2.604,0.365 false 2.906,0.781 2.781,1.063 2.781,1.063 2.677,1.063 false 2.438,0.281 2.792,0.521 0.354,0.24 10 false *1 2.5,0.979 2.813,1.146 0.313,0.167 10 false *2
*1 Manual Valve Lever Shaft Sub-assembly
*2 Parking Lock Rod Sub-assembly


Parking lock rod sub-assembly as shown in the illustration, and install the parking lock rod sub-assembly.

NOTICE:

Securely align the cutouts of the parking lock rod sub-assembly and manual valve lever shaft sub-assembly.



Hide 35506J 51.INSTALL MANUAL VALVE LEVER SHAFT RETAINER SPRING

a.
C362458

Install the manual valve lever shaft retainer spring to the automatic transaxle case sub-assembly.


Hide 35596 52.INSTALL PAWL STOPPER PLATE

a.
C362457

Install the pawl stopper plate to the automatic transaxle case sub-assembly with the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35505 53.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

a.
C362456

Install the manual valve lever sub-assembly to the automatic transaxle case sub-assembly.

NOTICE:

The pin portion of the manual valve lever shaft sub-assembly must be inserted into the slot of the manual valve lever sub-assembly.



Hide 35506 54.INSTALL MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C362453

Coat a new O-ring with Toyota Genuine ATF WS and install it to the manual valve lever shaft sub-assembly.

NOTICE:

Ensure that the O-ring it not twisted.



b.
C362454

Align the cutouts of the manual valve lever sub-assembly and manual valve lever shaft sub-assembly, and install the manual valve lever shaft sub-assembly.

HINT:

Installing the manual valve lever shaft sub-assembly to the area shown in the illustration will align the cutouts.



c.
C362455

Secure the manual valve lever shaft sub-assembly to the automatic transaxle case sub-assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35775K 55.INSTALL NO. 5 THRUST BEARING RACE

a.
C362450

Coat the No. 5 thrust bearing race with Toyota Genuine ATF WS and install it to the sun gear input hub sub-assembly.

No. 5 Thrust Bearing Race Diameter:
Inside Outside
34.2 mm (1.35 in.) 47.3 mm (1.86 in.)



Hide 56.INSTALL THRUST NEEDLE ROLLER BEARING

a.
C362449

Coat the thrust needle roller bearing with Toyota Genuine ATF WS and install it to the sun gear input hub sub-assembly.

Thrust Needle Roller Bearing Diameter:
Inside Outside
33.3 mm (1.31 in.) 46.3 mm (1.82 in.)



Hide 35606M 57.INSTALL SUN GEAR INPUT HUB SUB-ASSEMBLY

a.
C362448

Install the sun gear input hub sub-assembly to the counter drive gear sub-assembly.


Hide 35612B 58.INSTALL FORWARD CLUTCH PISTON

a.
C362447

Apply a light coat of Toyota Genuine ATF WS to a new D-ring and install it to the clutch drum sub-assembly.

HINT:
·

Be careful not to damage or twist the D-ring.

·

The rounded surface of the D-ring will be on the outer side of the ring groove.




b.
C362445

Apply a light coat of Toyota Genuine ATF WS to a new O-ring and install it to the clutch drum sub-assembly.

NOTICE:

Be careful not to damage or twist the O-ring.



c.
C362444

Apply a light coat of Toyota Genuine ATF WS to the forward clutch piston and install it to the clutch drum sub-assembly.

NOTICE:
·

Make sure that the O-ring and the D-ring is not damaged or does not jump out of position during installation.

·

Make sure the lip is not cut or folded.




Hide 35650B 59.INSTALL REAR CLUTCH PISTON RETURN COMPRESSION SPRING

a.
C362442

Install the rear clutch piston return compression spring to the forward clutch piston.

NOTICE:

Make sure to install in the correct direction.



Hide 35668 60.INSTALL NO. 1 CLUTCH BALANCER

a.

Apply a light coat of Toyota Genuine ATF WS to the lip seal of the forward clutch piston.


b.
C362440

Install the No. 1 clutch balancer to the forward clutch piston.

NOTICE:

Be careful not to damage the lip seal of the forward clutch piston.



c.
C362439N01
1.281,0.552 1.615,0.219 false 2.219,1.792 2.802,1.531 true 1.688,0.125 2.146,0.323 0.458,0.198 10 false SST 1.885,1.729 2.198,1.885 0.313,0.156 10 true SST

Place SST on the No. 1 clutch balancer and compress the rear clutch piston return compression spring with a press.

SST
09387-00020  

NOTICE:

Stop the press when the rear clutch piston return compression spring is flush with the snap ring groove.



d.

Using SST, install the snap ring to the clutch drum sub-assembly.

SST
09350-30020  (09350-07070)

NOTICE:

Make sure that the snap ring is installed in the groove of the clutch drum sub-assembly correctly.



Hide 35633 61.INSTALL FRONT CLUTCH CLUTCH DISC

a.
C362438C01
1.875,0.188 2.063,0.271 false 1.833,2.667 1.833,0.917 1.833,0.917 2.01,0.917 false 1.833,2.667 2.01,2.667 false 1.844,1.365 2.021,1.365 false 1.646,1.823 2.01,1.823 false 1.833,2.25 2.01,2.25 false 3.198,2.781 3.198,0.677 3.198,0.677 3.031,0.677 false 3.042,2.49 3.198,2.49 false 3.031,2.042 3.198,2.042 false 3.031,1.594 3.198,1.594 false 3.042,1.135 3.198,1.135 false 1.688,0.104 2,0.26 0.313,0.156 10 false *1 3.125,2.813 3.323,3.01 0.198,0.198 10 false *2 1.438,1.729 1.75,1.885 0.313,0.156 10 false *3 1.115,0.479 1.427,0.635 0.313,0.156 10 false *a 1.125,1.146 1.438,1.302 0.313,0.156 10 false *b
*1 Forward Clutch Flange
*2 Front Clutch Clutch Disc
*3 Forward Multiple Disc Clutch Clutch Plate
*a Snap Ring Side
*b Front Clutch Clutch Disc Side


Install the 5 forward multiple disc clutch clutch plates, 5 front clutch clutch discs and forward clutch flange to the clutch drum sub-assembly.

NOTICE:
·

Be careful during assembly because there are 2 types of forward multiple disc clutch clutch plate with different thicknesses.

·

Assemble the forward clutch flange with its tapered surface facing toward the front clutch clutch disc.




b.
C362437

Using a screwdriver with its tip wrapped in protective tape, install the snap ring to the clutch drum sub-assembly.

NOTICE:
·

Be careful not to damage the clutch drum sub-assembly.

·

Make sure that the snap ring is installed in the groove of the clutch drum sub-assembly correctly.




Hide 63.INSTALL C-1 CLUTCH ASSEMBLY

a.
C362435

Install the C-1 clutch assembly to the sun gear input hub sub-assembly.


Hide 35776 64.INSTALL NO. 6 THRUST BEARING RACE

a.
C362434

Coat the No. 6 thrust bearing race with Toyota Genuine ATF WS and install it to the C-1 clutch assembly.

No. 6 Thrust Bearing Race Diameter:
Inside Outside
38.1 mm (1.50 in.) 50.2 mm (1.98 in.)



Hide 65.INSTALL THRUST NEEDLE ROLLER BEARING

a.
C362433

Coat the thrust needle roller bearing with Toyota Genuine ATF WS and install it to the C-1 clutch assembly.

Thrust Needle Roller Bearing Diameter:
Inside Outside
39.2 mm (1.54 in.) 52.6 mm (2.07 in.)



Hide 35743 66.INSTALL FRONT PLANETARY RING GEAR

a.
C362432

Install the front planetary ring gear flange to the front planetary ring gear.


b.
C362431

Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the front planetary ring gear.

NOTICE:

Be careful not to damage the front planetary ring gear and front planetary ring gear flange.



c.
C362430

Install the front planetary ring gear with front planetary ring gear flange to the C-1 clutch assembly.


Hide 35749B 67.INSTALL REAR INPUT SHAFT OIL SEAL RING

a.
C362429

Apply a small amount of MP grease to the entire circumference of the rear input shaft oil seal ring installation groove portion.

HINT:

By applying MP grease, the wobble within the rear input shaft oil seal ring installation groove will be eliminated, preventing damage to the rear input shaft oil seal ring at the time of front planetary gear assembly installation.



b.

Coat 2 new rear input shaft oil seal rings with Toyota Genuine ATF WS and install them to the front planetary gear assembly.

NOTICE:

While making the spread of the opening of the rear input shaft oil seal ring as small as possible, install it to the front planetary gear assembly. If the ring opening is spread, briefly hold it closed with your fingers to return it to its original condition.



Hide 35712E 68.INSTALL INPUT SHAFT OIL SEAL RING

a.
C362428

Apply a small amount of MP grease to the entire circumference of the input shaft oil seal ring installation groove portion.

HINT:

By applying MP grease, the wobble within the input shaft oil seal ring installation groove will be eliminated, preventing damage to the input shaft oil seal ring at the time of front oil pump assembly and torque converter clutch assembly installation.



b.

Coat 5 new input shaft oil seal rings with Toyota Genuine ATF WS and install them to the front planetary gear assembly.

NOTICE:

While making the spread of the opening of the input shaft oil seal ring as small as possible, install it to the front planetary gear assembly. If the ring opening is spread, briefly hold it closed with your fingers to return it to its original condition.



Hide 35777 69.INSTALL NO. 7 THRUST BEARING RACE

a.
C362427

Coat the No. 7 thrust bearing race with Toyota Genuine ATF WS and install it to the front planetary gear assembly.

No. 7 Thrust Bearing Race Diameter:
Inside Outside
59.8 mm (2.35 in.) 77.0 mm (3.03 in.)


NOTICE:

Securely insert the claw of the No. 7 thrust bearing race into the hole of the front planetary gear assembly.


HINT:

When installing the front planetary gear assembly, if the No. 7 thrust bearing race falls off, coat the front planetary gear assembly installation surface with MP grease and install the parts.



Hide 70.INSTALL THRUST NEEDLE ROLLER BEARING

a.
C362425

Coat the thrust needle roller bearing with Toyota Genuine ATF WS and install it to the front planetary ring gear.

Thrust Needle Roller Bearing Diameter:
Inside Outside
58.3 mm (2.30 in.) 75.0 mm (2.95 in.)



Hide 35720 71.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
C362423

Install the front planetary gear assembly to the front planetary ring gear.


Hide 35778 72.INSTALL NO. 8 THRUST BEARING RACE

a.
C362421

Coat the No. 8 thrust bearing race with Toyota Genuine ATF WS and install it to the front planetary ring gear.

No. 8 Thrust Bearing Race Diameter:
Inside Outside
31.7 mm (1.25 in.) 52.3 mm (2.06 in.)



Hide 73.INSTALL THRUST NEEDLE ROLLER BEARING

a.
C362422

Coat the thrust needle roller bearing with Toyota Genuine ATF WS and install it to the front planetary ring gear.

Thrust Needle Roller Bearing Diameter:
Inside Outside
31.7 mm (1.25 in.) 52.3 mm (2.06 in.)



Hide 35779A 74.INSTALL NO. 9 THRUST BEARING RACE

a.
C362421

Coat the No. 9 thrust bearing race with Toyota Genuine ATF WS and install it to the front planetary ring gear.

No. 9 Thrust Bearing Race Diameter:
Inside Outside
32.6 mm (1.28 in.) 54.2 mm (2.13 in.)



Hide 35719B 75.INSTALL PLANETARY SUN GEAR

a.
C362420

Install the planetary sun gear to the front planetary gear assembly.


Hide 35738 76.INSTALL NO. 2 PLANETARY CARRIER THRUST WASHER

a.
C362419

Install the No. 2 planetary carrier thrust washer to the front planetary gear assembly.

NOTICE:

Securely insert each protrusion of the No. 2 planetary carrier thrust washer into each indentation of the front planetary gear assembly.



Hide 34610 79.INSTALL C-3 AND C-4 CLUTCH ASSEMBLY

a.
C362405

Install the C-3 and C-4 clutch assembly to the front planetary gear assembly.


Hide 35737 80.INSTALL PLANETARY CARRIER THRUST WASHER

a.
C362404

Install the planetary carrier thrust washer to the C-3 and C-4 clutch assembly.

NOTICE:

Securely insert the protrusion of the planetary carrier thrust washer into the indentation of the C-3 and C-4 clutch assembly.



Hide 81.INSTALL FRONT OIL PUMP ASSEMBLY

a.
C362402N01
0.344,1.615 0.479,1.792 0.135,0.177 10 false A 0.708,0.031 0.844,0.208 0.135,0.177 10 false B 1.969,0.135 2.104,0.313 0.135,0.177 10 false A 2.396,0.406 2.531,0.583 0.135,0.177 10 false B 2.646,1.313 2.781,1.49 0.135,0.177 10 false B 2.573,0.979 2.708,1.156 0.135,0.177 10 false B 2.75,1.99 2.885,2.167 0.135,0.177 10 false B

Install the front oil pump assembly to the automatic transaxle case sub-assembly with the 7 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

Bolt Length:
Bolt (A) Bolt (B)
40 mm (1.57 in.) 30 mm (1.18 in.)



Hide 35409D 82.INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C362401C01
0.927,1.073 0.969,0.896 false 0.427,1.052 0.5,0.781 false 0.844,1.104 1.156,1.26 0.313,0.156 10 false *1 0.354,1.104 0.667,1.26 0.313,0.156 10 false *2 0.698,0.271 1.01,0.427 0.313,0.156 10 false *a 2.396,0.26 2.708,0.417 0.313,0.156 10 false *b
*1 Manual Detent Spring Sub-assembly
*2 Manual Valve Lever Shaft Sub-assembly
*a Correct
*b Incorrect


Install the manual detent spring sub-assembly to the front oil pump assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:
·

Securely insert the claw of the manual detent spring sub-assembly into the hole of the front oil pump assembly.

·

Check that the roller portion of the manual detent spring sub-assembly is engaged with the manual valve lever shaft sub-assembly.




Hide 35355 83.INSTALL OIL PUMP SPROCKET REAR THRUST WASHER

a.
C362399

Install the oil pump sprocket rear thrust washer to the front oil pump assembly.

NOTICE:

Securely insert the protrusion of the oil pump sprocket rear thrust washer into the indentation of the front oil pump assembly.



Hide 35781C 84.INSTALL TRANSMISSION DRIVE CHAIN

a.
C368136C01
0.552,1.083 0.802,0.917 true 1.833,1.083 2.083,0.917 true 2.438,2.708 3.031,2.188 true 0.385,1.01 0.698,1.167 0.313,0.156 10 false *1 0.542,0.333 0.854,0.49 0.313,0.156 10 false *a 1.854,0.344 2.167,0.5 0.313,0.156 10 false *b 3.073,2.083 3.385,2.24 0.313,0.156 10 false *c 1.667,1.01 1.979,1.167 0.313,0.156 10 false *1
*1 Front Oil Pump Drive Gear
*a Correct
*b Incorrect
*c Protective Tape


Using a screwdriver with its tip wrapped in protective tape, align the cutout of the front oil pump drive gear with the position (*a) shown in the illustration.

NOTICE:

Do not pry with excessive force when aligning the cutout of the front oil pump drive gear.



b.
C362397

Install the transmission drive chain together with the transmission oil pump drive sprocket and oil pump drive shaft sub-assembly to the front oil pump assembly.

NOTICE:
·

To avoid damaging the bush of the front oil pump assembly, install the transmission drive chain, transmission oil pump drive sprocket and oil pump drive shaft sub-assembly horizontally relative to the front oil pump assembly.

·

Align the cutout of the oil pump drive shaft sub-assembly and the cutout of the front oil pump drive gear, and install the parts.




Hide 35354 85.INSTALL OIL PUMP SPROCKET FRONT THRUST WASHER

a.
C362396

Install the oil pump sprocket front thrust washer to the transmission oil pump drive sprocket.

NOTICE:

Securely insert the long protrusion of the oil pump sprocket rear thrust washer into the slot of the oil pump sprocket front thrust washer.



Hide 35617 86.INSTALL CLUTCH DRUM OIL SEAL RING

a.
C362394

Apply a small amount of MP grease to the entire circumference of the clutch drum oil seal ring installation groove portion.

HINT:

By applying MP grease, the wobble within the clutch drum oil seal ring installation groove will be eliminated, preventing damage to the clutch drum oil seal ring at the time of torque converter clutch assembly installation.



b.

Coat a new clutch drum oil seal ring with Toyota Genuine ATF WS and install it to the front oil pump assembly.

NOTICE:

While making the spread of the opening of the clutch drum oil seal ring as small as possible, install it to the front oil pump assembly. If the ring opening is spread, briefly hold it closed with your fingers to return it to its original condition.



Hide 87.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C365897

Install the differential case assembly to the automatic transaxle case sub-assembly.


Hide 35847C 88.INSTALL TRANSMISSION LUBE APPLY TUBE

a.
C362645C01
2.073,2.219 2.385,2.375 0.313,0.156 10 false *a 0.5,2.219 0.813,2.375 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Install the transmission lube apply tube to the transaxle housing.

NOTICE:

Insert the transmission lube apply tube until its spool portion is contacting the transaxle housing.



b.
C362391

Install the clamp to the transaxle housing with a new bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35882C 89.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C362644C01
2.094,2.219 2.406,2.375 0.313,0.156 10 false *a 0.531,2.219 0.844,2.375 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Install the differential gear lube apply tube to the transaxle housing.

NOTICE:

Insert the differential gear lube apply tube until its spool portion is contacting the transaxle housing.



Hide 35394 90.INSTALL TRANSMISSION OIL CLEANER MAGNET

a.
C362389

Install the 3 transmission oil cleaner magnets to the transaxle housing oil separator.


Hide 35174 91.INSTALL TRANSAXLE HOUSING OIL SEPARATOR

a.
C362388

Install the transaxle housing oil separator to the transaxle housing with 3 new bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35111C 92.INSTALL TRANSAXLE HOUSING

HINT:
C362609C02
1.521,0.458 1.885,0.198 true 1,1.49 1.385,1.979 true 1.448,1.938 1.667,2.146 0.219,0.208 10 true *a 1.938,0.094 2.177,0.302 0.24,0.208 10 true *b
*a TMC Made
*b AW Made


TMC (TOYOTA) Made and AW (AISIN AW) Made components can be identified by the differing locations where the serial number is stamped.


NOTICE:
C362384

When installing the transaxle housing check that the transmission drive chain rotates smoothly.


a.

Peel off the old seal packing from the transaxle housing and automatic transaxle case sub-assembly installation surface, and clean it.

NOTICE:

Do not damage the installation surface.



b.
C365901

Clean the 21 bolts and bolt holes in the automatic transaxle case sub-assembly.


c.
C365902C01
0,0 0,0 false
V100145

Area to be cleaned


Clean the inner chamfer of the automatic transaxle case sub-assembly shown in the illustration.


d.
C365903

Apply seal packing to the automatic transaxle case sub-assembly as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Standard Seal Diameter:

1.8 mm (0.0709 in.)


NOTICE:

After applying seal packing, install the transaxle housing within 3 minutes and tighten the bolts within 20 minutes of applying the seal packing.



e.
C365896C01
1.854,0.021 2.167,0.281 0.313,0.26 10 false *1 0.615,0.396 0.948,0.719 0.333,0.323 10 false *2 2.99,0.531 3.302,0.792 0.313,0.26 10 false *1 3.073,0.823 3.385,1.083 0.313,0.26 10 false *1 3.031,1.073 3.344,1.333 0.313,0.26 10 false *1 3.01,1.5 3.323,1.76 0.313,0.26 10 false *1
*1 Transaxle Case Gaskets
*2 O-ring


Coat 5 new transaxle case gaskets with Toyota Genuine ATF WS and install it to the front oil pump assembly.


f.

Coat a new O-ring with Toyota Genuine ATF WS and install it to the automatic transaxle case sub-assembly.


g.

for TMC Made:

i.
C378383N01
1.438,0.354 1.604,0.542 0.167,0.188 10 true A 1.917,0.396 2.083,0.583 0.167,0.188 10 true A 2.146,0.469 2.313,0.656 0.167,0.188 10 true A 2.927,0.76 3.094,0.948 0.167,0.188 10 true A 2.281,2.875 2.448,3.063 0.167,0.188 10 true A 1.958,2.875 2.125,3.063 0.167,0.188 10 true A 1.188,0.344 1.354,0.531 0.167,0.188 10 true B 0.708,0.635 0.875,0.823 0.167,0.188 10 false B 0.521,0.792 0.708,0.979 0.188,0.188 10 false B 0.177,1.271 0.323,1.469 0.146,0.198 10 true B 0.083,1.625 0.229,1.823 0.146,0.198 10 true B 0.052,1.885 0.198,2.083 0.146,0.198 10 true B 0.24,2.5 0.385,2.698 0.146,0.198 10 true B 0.438,2.698 0.583,2.896 0.146,0.198 10 true B 1.021,2.885 1.167,3.083 0.146,0.198 10 true B 1.323,2.896 1.469,3.094 0.146,0.198 10 true B 1.625,2.906 1.771,3.104 0.146,0.198 10 true B 2.448,0.573 2.594,0.771 0.146,0.198 10 true B

Install the transaxle housing to the automatic transaxle case sub-assembly with the 6 bolts (A) and 12 bolts (B).

Torque:
Bolt (A) and (B) : 29.4 N*m (300 kgf*cm, 22 ft.*lbf)

Bolt Length:
Bolt (A) Bolt (B)
40 mm (1.57 in.) 35 mm (1.38 in.)



ii.
P000601C53
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of the 3 bolts (C).

Bolt Length:

40 mm (1.57 in.)


Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the bolts immediately after applying adhesive to prevent foreign matter from attaching to them.


HINT:

The bolt (C) is in one location shown in the following step.



iii.
C378384N01
3.188,1.219 3.344,1.417 0.156,0.198 10 false C 3.188,1.969 3.344,2.167 0.156,0.198 10 false C 3.042,2.729 3.198,2.927 0.156,0.198 10 false C

Install the 3 bolts (C).

Torque:
Bolt (C) : 22.7 N*m (231 kgf*cm, 17 ft.*lbf)



h.

for AW Made:

i.
C362561N01
1.427,0.365 1.594,0.521 0.167,0.156 10 false A 1.188,0.365 1.354,0.542 0.167,0.177 10 false B 1.917,0.417 2.083,0.573 0.167,0.156 10 false A 2.146,0.469 2.313,0.625 0.167,0.156 10 true A 2.917,0.729 3.083,0.885 0.167,0.156 10 true A 3.094,1.063 3.26,1.219 0.167,0.156 10 true A 3.167,1.969 3.333,2.125 0.167,0.156 10 true A 3.021,2.688 3.188,2.844 0.167,0.156 10 true A 2.271,2.865 2.438,3.021 0.167,0.156 10 true A 1.958,2.885 2.125,3.042 0.167,0.156 10 true A 0.719,0.625 0.885,0.802 0.167,0.177 10 false B 0.531,0.802 0.698,0.979 0.167,0.177 10 false B 0.208,1.26 0.375,1.438 0.167,0.177 10 false B 0.104,1.615 0.271,1.792 0.167,0.177 10 false B 0.083,1.885 0.25,2.063 0.167,0.177 10 false B 0.271,2.448 0.438,2.625 0.167,0.177 10 false B 0.458,2.677 0.625,2.854 0.167,0.177 10 false B 1.021,2.875 1.188,3.052 0.167,0.177 10 false B 1.323,2.885 1.49,3.063 0.167,0.177 10 false B 2.448,0.604 2.615,0.781 0.167,0.177 10 true B 1.625,2.896 1.792,3.073 0.167,0.177 10 false B

Install the transaxle housing to the automatic transaxle case sub-assembly with the 9 bolts (A) and 12 bolts (B).

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

Bolt Length:
Bolt (A) Bolt (B)
40 mm (1.57 in.) 35 mm (1.38 in.)




Hide 89413S 94.INSTALL TRANSMISSION REVOLUTION SENSOR (NC)

a.
C361013

Install the transmission revolution sensor (NC) to the counter drive gear sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 89413N 95.INSTALL TRANSMISSION REVOLUTION SENSOR (NT)

a.
C361014

Install the transmission revolution sensor (NT) to the automatic transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35410 96.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C361027C01
1.74,0.271 1.948,0.479 0.208,0.208 10 true *1 0.833,1.604 1.01,1.781 0.177,0.177 10 true *3 2.417,1.667 2.583,1.854 0.167,0.188 10 true *1 2.375,1.958 2.552,2.135 0.177,0.177 10 true *1 0.906,1.979 1.083,2.146 0.177,0.167 10 true *2
*1 Transaxle Case Gasket
*2 No. 1 Front Oil Pump Cover Gasket
*3 No. 2 Front Oil Pump Cover Gasket


Coat 2 new transaxle case gaskets with Toyota Genuine ATF WS and install them to the automatic transaxle case sub-assembly.


b.

Coat a new transaxle case gasket with Toyota Genuine ATF WS and install it to the counter drive gear sub-assembly.


c.

Coat a new No. 1 front oil pump cover gasket with Toyota Genuine ATF WS and install it to the front oil pump assembly.


d.

Coat a new No. 2 front oil pump cover gasket with Toyota Genuine ATF WS and install it to the front oil pump assembly.


e.
C362377C01
1.521,0.719 2.021,0.5 true 0.583,0.323 1.25,0.531 true 2.052,0.417 2.365,0.573 0.313,0.156 10 false *1 0.417,0.25 0.729,0.406 0.313,0.156 10 false *2
*1 Manual Valve
*2 Manual Valve Lever Sub-assembly


Align the slit portion of the manual valve and the manual valve lever sub-assembly as shown in the illustration, and install the transmission valve body assembly to the automatic transaxle case sub-assembly with the 9 bolts.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)

NOTICE:

Be careful that the transmission revolution sensor (NC) wire is not pinched.



f.
C362378C01
0,0 0,0 false
V100145

Do not let transmission revolution sensor (NC) wire ride up over this area.


Engage the clamp to connect the transmission revolution sensor (NC) wire connector.

NOTICE:

To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, do not let the transmission revolution sensor (NC) wire ride up over the area shown in the illustration.



Hide 82125J 97.INSTALL TRANSMISSION WIRE

a.
C362373

Coat the O-ring of the transmission wire with Toyota Genuine ATF WS.


b.
C362372

Install the transmission wire to the automatic transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.
C361009

Connect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.


d.
C361010

Install the temperature sensor to the transmission valve body assembly with the bolt and temperature sensor clamp.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)

NOTICE:
C362643C02
1.688,1.646 1.99,1.833 true 1.083,1.167 1.5,1.333 true 1.969,1.865 2.198,2.031 0.229,0.167 10 true *a 0.823,1.063 1.052,1.219 0.229,0.156 10 true *b
*a Transmission Wire (Temperature Sensor Wire)
*b Transmission Revolution Sensor (NC) Wire


To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, pass the transmission revolution sensor (NC) wire under the transmission wire (temperature sensor wire) as shown in the illustration.



e.
C365930

Connect the 9 solenoid valve connectors.

NOTICE:
C362374C01
0,0 0,0 false
V100145

Do not let transmission wire protrude into this area.


·

To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, do not let the transmission wire ride up over the area shown in the illustration.

·

To prevent it from being pinched between the transmission case side cover and the automatic transaxle case sub-assembly, do not let the transmission wire protrude toward the transmission case side cover installation surface.




f.
C365931

Engage the clamp to connect the transmission wire to the solenoid lock plate.


Hide 35151F 98.INSTALL TRANSMISSION CASE SIDE COVER (for TMC Made)

HINT:
C362609C02
1.521,0.458 1.885,0.198 true 1,1.49 1.385,1.979 true 1.448,1.938 1.667,2.146 0.219,0.208 10 true *a 1.938,0.094 2.177,0.302 0.24,0.208 10 true *b
*a TMC Made
*b AW Made


TMC (TOYOTA) Made and AW (AISIN AW) Made components can be identified by the differing locations where the serial number is stamped.


a.
C362642C01
0,0 0,0 false
V100145

Area to be cleaned


Clean the transmission case side cover installation surface of the automatic transaxle case sub-assembly.

NOTICE:

Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly.



b.
C378385

Clean the 3 bolt holes shown in the illustration.


c.
P000601C53
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the bolt (A) and 2 bolts (D).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the bolts immediately after applying adhesive to prevent foreign matter from attaching to them.


HINT:

The bolt (A) and 2 bolts (D) are in the locations shown in the following step.



d.
C365942N06
1.094,1.979 1.292,2.177 0.198,0.198 10 false A 1.635,1.979 1.833,2.177 0.198,0.198 10 false C 2.177,1.979 2.375,2.177 0.198,0.198 10 false C 2.844,1.521 3.042,1.719 0.198,0.198 10 false C 2.885,0.938 3.083,1.135 0.198,0.198 10 false C 2.771,0 2.969,0.198 0.198,0.198 10 false B 2.031,0.01 2.229,0.208 0.198,0.198 10 false C 1.365,0 1.563,0.198 0.198,0.198 10 false C 0.896,0.625 1.052,0.823 0.156,0.198 10 true D 0.896,1.156 1.052,1.354 0.156,0.198 10 true D

Temporarily install a new transmission case side cover to the automatic transaxle case sub-assembly with the 2 bolts ((A) and (B)).

NOTICE:
·

Bolt (A) is an adhesive-coated bolt.

·

To avoid damaging the gasket, prevent it from contacting the surrounding area during installation procedures.




e.

Temporarily install the 6 bolts (C) and 2 bolts (D).

NOTICE:

Bolt (D) is an adhesive-coated bolt.



f.
C365942N05
1.073,1.958 1.469,2.167 0.396,0.208 10 false 1 1.635,1.979 1.833,2.177 0.198,0.198 10 false 8 2.531,1.938 2.729,2.135 0.198,0.198 10 false 4 2.844,1.521 3.115,1.74 0.271,0.219 10 false 10 2.885,0.938 3.083,1.135 0.198,0.198 10 false 6 2.771,0 2.969,0.198 0.198,0.198 10 false 2 2.031,0.01 2.229,0.208 0.198,0.198 10 false 7 1.365,0 1.563,0.198 0.198,0.198 10 false 3 0.896,0.625 1.052,0.823 0.156,0.198 10 true 5 0.896,1.156 1.052,1.354 0.156,0.198 10 true 9

Fully tighten the 10 bolts in the order shown in the illustration.

Torque:
Bolt (A) and Bolt (D) : 6.5 N*m (66 kgf*cm, 58 in.*lbf)
Bolt (B) and Bolt (C) : 7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 35151F 99.INSTALL TRANSMISSION CASE SIDE COVER (for AISIN AW Made)

HINT:
C362609C02
1.521,0.458 1.885,0.198 true 1,1.49 1.385,1.979 true 1.448,1.938 1.667,2.146 0.219,0.208 10 true *a 1.938,0.094 2.177,0.302 0.24,0.208 10 true *b
*a TMC Made
*b AW Made


TMC (TOYOTA) Made and AW (AISIN AW) Made components can be identified by the differing locations where the serial number is stamped.


a.
C362642C01
0,0 0,0 false
V100145

Area to be cleaned


Clean the transmission case side cover installation surface of the automatic transaxle case sub-assembly.

NOTICE:

Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly.



b.
C365942N01
1.094,1.979 1.292,2.177 0.198,0.198 10 false A 1.635,1.979 1.833,2.177 0.198,0.198 10 false C 2.177,1.979 2.375,2.177 0.198,0.198 10 false C 2.844,1.521 3.042,1.719 0.198,0.198 10 false C 2.885,0.938 3.083,1.135 0.198,0.198 10 false C 2.771,0 2.969,0.198 0.198,0.198 10 false B 2.031,0.01 2.229,0.208 0.198,0.198 10 false C 1.365,0 1.563,0.198 0.198,0.198 10 false C 0.896,0.625 1.052,0.823 0.156,0.198 10 true C 0.896,1.156 1.052,1.354 0.156,0.198 10 true C

Temporarily install a new transmission case side cover to the automatic transaxle case sub-assembly with the 2 bolts (A and B).

NOTICE:

To avoid damaging the gasket, prevent it from contacting the surrounding area during installation procedures.



c.

Temporarily install the 8 bolts (C).


d.
C365942N05
1.073,1.958 1.469,2.167 0.396,0.208 10 false 1 1.635,1.979 1.833,2.177 0.198,0.198 10 false 8 2.531,1.938 2.729,2.135 0.198,0.198 10 false 4 2.844,1.521 3.115,1.74 0.271,0.219 10 false 10 2.885,0.938 3.083,1.135 0.198,0.198 10 false 6 2.771,0 2.969,0.198 0.198,0.198 10 false 2 2.031,0.01 2.229,0.208 0.198,0.198 10 false 7 1.365,0 1.563,0.198 0.198,0.198 10 false 3 0.896,0.625 1.052,0.823 0.156,0.198 10 true 5 0.896,1.156 1.052,1.354 0.156,0.198 10 true 9

Fully tighten the 10 bolts in the order shown in the illustration.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 35104B 100.INSTALL NO. 1 BREATHER PLUG (ATM)

a.

Coat the O-ring portion of the No. 1 breather plug (ATM) with Toyota Genuine ATF WS.


b.
C362520C01
2.583,2.594 3,1.833 true 2.646,2.708 3.083,2.25 true 3.063,1.74 3.375,1.896 0.313,0.156 10 false *a 3.156,2.146 3.385,2.385 0.229,0.24 10 false *b
*a Indented Portion
*b Detent Aligned


Engage each claw to install a new No. 1 breather plug (ATM) to the automatic transaxle case sub-assembly.

NOTICE:

Securely push in the automatic transaxle case sub-assembly until the No. 1 breather plug (ATM) is engaged.


HINT:

Install the No. 1 breather plug (ATM) with its detent aligned with the indented portion of the automatic transaxle case sub-assembly.



Hide 32905 101.INSTALL NO. 1 OIL COOLER OUTLET TUBE SUB-ASSEMBLY

a.
C362362C02
2.344,1.865 2.594,1.969 false 2.646,1.885 2.958,2.042 0.313,0.156 10 false *a
*a Lock Nut


Rotate the lock nut of the No. 1 oil cooler outlet tube sub-assembly all the way in the loosening direction.


b.
C362361

Coat a new O-ring with Toyota Genuine ATF WS and install it to the No. 1 oil cooler outlet tube sub-assembly.

NOTICE:

Ensure that the O-ring is not twisted.



c.
C362363C01
2.552,1.125 2.698,1.375 false 2.521,0.823 2.781,1.302 false 2.365,1.01 2.677,1.167 0.313,0.156 10 false *1 2.313,0.708 2.625,0.865 0.313,0.156 10 false *2
*1 Washer Plate
*2 Automatic Transaxle Case Sub-assembly


Rotate the entire No. 1 oil cooler outlet tube sub-assembly until the washer plate contacts the automatic transaxle case sub-assembly to install the No. 1 oil cooler outlet tube sub-assembly.


d.
C365919C01
2.042,1.135 2.333,1.323 0.292,0.188 10 true *a 2.365,0.271 2.552,0.417 0.188,0.146 10 true *b
*a 45°00' (45°)
*b +/- 7°30' (+/- 7.5°)


Adjust the tip of the No. 1 oil cooler outlet tube sub-assembly to the location shown in the illustration.


e.
C365920C01
0.844,0.917 0.896,0.698 0.896,0.698 1,0.698 false 0.542,1.427 0.635,1.427 0.635,1.427 0.698,1.208 false 0.927,2.448 0.979,2.229 0.979,2.229 1.083,2.229 false 0.354,1.313 0.688,1.542 0.333,0.229 10 false *a 1.052,0.594 1.406,0.917 0.354,0.323 10 false *b 1.135,2.115 1.385,2.302 0.25,0.188 10 false *c 1.813,2.938 2.083,3.125 0.271,0.188 10 false *d
*a Hold
*b Tighten
*c Union Nut Wrench
*d Torque Wrench Fulcrum Length


Using 17 mm and 19 mm union nut wrenches, hold the No. 1 oil cooler outlet tube sub-assembly and tighten the lock nut.

Torque:
Specified tightening torque : 31.1 N*m (317 kgf*cm, 23 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

26.7 N*m (272 kgf*cm, 20 ft.*lbf)




Hide 32901C 102.INSTALL OIL COOLER UNION SUB-ASSEMBLY

a.
C362358C01
1.49,2.802 1.656,2.719 false 2.146,2.823 1.635,3.031 1.635,3.031 1.844,2.833 true 1.281,2.74 1.594,2.896 0.313,0.156 10 false *1 1.438,2.979 1.75,3.135 0.313,0.156 10 false *2
*1 Oil Cooler Union Bolt
*2 Gasket


Pass the oil cooler union sub-assembly through 2 new gaskets and temporarily install it to the automatic transaxle case sub-assembly.


b.

Temporarily install the oil cooler union sub-assembly bracket portion to the automatic transaxle case sub-assembly with the bolt.


c.

Fully tighten the oil cooler union bolt.

Torque:
22.6 N*m (230 kgf*cm, 17 ft.*lbf)


d.

Fully tighten the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 35125C 103.INSTALL NO. 1 TRANSMISSION OIL FILLER TUBE

a.
C362356

Using a 6 mm socket hexagon wrench, install the No. 1 transmission oil filler tube to the transaxle housing.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


Hide 35405C 104.INSTALL OVERFLOW PLUG

a.
C362355

Using a 10 mm socket hexagon wrench, install the overflow plug and a new gasket to the transaxle housing.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)

NOTICE:

To prevent the gasket from being deformed when tightening, coat the gasket with Toyota Genuine ATF WS.



Hide 35015S 105.INSTALL REFILL PLUG

a.
C362354

Install the refill plug and a new gasket to the automatic transaxle case sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

To prevent the gasket from being deformed when tightening, coat the gasket with Toyota Genuine ATF WS.



Hide 84540 106.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C362351

Temporarily install the park/neutral position switch assembly to the automatic transaxle case sub-assembly with the 2 bolts.


b.
C362350

Temporarily install the transmission control shaft lever to the manual valve lever shaft sub-assembly.


c.
C362352C01
2.896,0.292 3.104,0.469 0.208,0.177 10 true *a 1.625,0.031 1.792,0.208 0.167,0.177 10 true *b
*a P Position
*b N Position


Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.


d.

Remove the transmission control shaft lever from the manual valve lever shaft sub-assembly.


e.
C362353C01
1.719,1.365 2.365,0.948 true 1.438,1.219 0.75,0.917 true 0.531,0.802 0.719,0.99 0.188,0.188 10 true *a 2.427,0.802 2.635,1 0.208,0.198 10 true *b
*a Neutral Basic Line
*b Protrusion


Align the protrusion with the neutral basic line.


f.

Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35572A 107.INSTALL TRANSMISSION CONTROL SHAFT LEVER

a.
C362350

Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the washer and nut.

NOTICE:

Be careful of the assembly direction of the transmission control shaft lever.


Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)