Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _060164 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0298261 AUTOMATIC TRANSAXLE SYSTEM D

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  ROAD TEST  


PROBLEM SYMPTOM CONFIRMATION


a.

Based on the result of the customer problem analysis, try to reproduce the symptoms. If the problem is that the transaxle does not shift up, shift down, or the shift point is too high or too low, conduct the following road test referring to the automatic shift schedule and simulate the problem symptoms.



ROAD TEST


CAUTION:

Strictly observe posted speed limits, traffic laws and road conditions when performing the road test.


NOTICE:
·

Be sure to inspect and adjust the engine before performing these tests.

·

Perform the road test with the engine coolant temperature between 60 and 100°C (140 and 212°F) and the ATF temperature between 50 and 100°C (122 and 212°F).

·

Perform these tests with the air conditioning and cruise control off.

Inspection Procedure
Transmission Control Switch Test With the vehicle stationary and the shift lever in D, move the shift lever to S and return it to D. Check that the meter display changes from D to the appropriate S gear and then back again.
S Position Test While driving with the shift lever in S, move the shift lever to "+" and "-". Check that the meter display changes accordingly.
D Position Shift Test While driving the vehicle normally, check that the transaxle shifts up and down through each gear properly.
Lock-up Function While driving on a level surface at a constant speed in the lock-up range with the shift lever in D, lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
P Position Test Stop the vehicle on an incline (approximately 5° or more). Then move the shift lever to P and release the parking brake. Check that the parking lock pawl holds the vehicle in place.
Abnormal Noise and Vibration Check for abnormal noise and vibration while driving the vehicle forward and backward, and during shift operations.
Fluid Leakage After performing all other road test inspections, check for fluid leakage.



HINT:

When checking for DTCs after a repair, drive the vehicle according to the monitor drive pattern.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>MONITOR DRIVE PATTERN


a.

Shift schedule confirmation

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Enter the following menus: Powertrain / Transmission / Data List.

Powertrain > Transmission > Data List
Tester Display
Vehicle Speed
Coolant Temperature
Accel Position from EFI
Shift Status
50003 373 212,205,401,179

iv.

Check that the "Shift Status" changes in accordance with the "Vehicle Speed" as shown in the following table.

Shift Schedule Chart:
Accelerator Pedal Position
(Accel Position from EFI)
14 +/- 1%
Shift Status
(Shift Lever in D)
1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th 6th to 7th 7th to 8th
Vehicle Speed 5 to 20 km/h
(3 to 12 mph)
20 to 30 km/h
(12 to 19 mph)
25 to 35 km/h
(16 to 22 mph)
30 to 40 km/h
(19 to 25 mph)
40 to 50 km/h
(25 to 31 mph)
50 to 60 km/h
(31 to 37 mph)
60 to 70 km/h
(37 to 43 mph)


NOTICE:
·

All vehicle speeds indicated in the above table are actual values. Therefore, if checking a shift point with a chassis dynamometer, keep in mind that there is a margin of error in the chassis dynamometer indication.

·

If checking a shift point against the vehicle speed indicated on the speedometer, remember to consider the speedometer correction rate and margin of error in the tester indication.





b.

Lock-up confirmation

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Enter the following menus: Powertrain / Transmission / Data List.

Powertrain > Transmission > Data List
Tester Display
Vehicle Speed
Engine Speed
Coolant Temperature
Accel Position from EFI
NT Sensor Speed
A/T Oil Temperature No.1
Lock Up Status
Shift Status
50003 373 212,211,205,401,174,180,178,179

iv.

When the following conditions are met, check that the difference between "Engine Speed" and "NT Sensor Speed" is 50 rpm or less.

Lock-up Schedule:
Accelerator Pedal Position
(Accel Position from EFI)
14 +/- 1%
Vehicle Speed
(Constant speed)
80 km/h (50 mph)
Shift Status 8th
Lock Up Status ON


HINT:

Lock-up prohibition conditions:

·

Engine coolant temperature is less than 20°C (68°F)

·

ATF temperature is less than 20°C (68°F) or higher than 110°C (230°F)

·

Throttle valve is fully closed

·

Stop light switch is on





c.

Manual down-shift permission speed

i.

Manual down-shift is permitted for each shift status when the vehicle speed is below the corresponding range shown in the following table.

Manual Down-shift Permission Speed Chart:
Accelerator Pedal Fully Closed
Shift Status
(Shift Lever in S)
4 to 3 3 to 2 2 to 1
Vehicle Speed 135 to 155 km/h
(84 to 96 mph)
85 to 100 km/h
(53 to 62 mph)
40 to 50 km/h
(25 to 31 mph)




d.

Shift schedule when throttle valve is fully open

Shift Schedule Chart:
Accelerator Pedal Fully Open
Shift Status
(Shift Lever in D)
1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th 6th to 7th 7th to 8th

*: Speed limiter activates before this speed range

Vehicle Speed 35 to 50 km/h
(22 to 31 mph)
80 to 90 km/h
(50 to 56 mph)
130 to 145 km/h
(81 to 90 mph)
180 to 195* km/h
(112 to 121* mph)
220* to 240* km/h
(137* to 149* mph)
275* to 295* km/h
(171* to 183* mph)
350* to 365* km/h
(217* to 227* mph)