Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _060164 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0298261 AUTOMATIC TRANSAXLE SYSTEM C

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P056014  System Voltage Circuit Short to Ground or Open  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history and freeze frame data. If the battery voltage falls below a minimum level, the stored ECM data will be cleared and the ECM will determine that there is a malfunction in the power supply circuit. The next time the engine is started, the ECM will illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P056014 System Voltage Circuit Short to Ground or Open 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Always

2.

Low ECM back-up power source circuit voltage

3.

3 seconds or more

4.

1-trip detection logic


·

Back-up power source circuit

·

Battery terminals

·

Battery

·

ECM


Comes on DTC stored SAE Code:
P0562

HINT:

If DTC P056014 is stored, the ECM will not store other DTCs.


WIRING DIAGRAM

A316542E04
1.167,2.302 2.24,2.5 1.073,0.198 10 false Battery 1.823,1.25 2.896,1.448 1.073,0.198 10 false FL MAIN 2.938,1.25 4.01,1.448 1.073,0.198 10 false EFI-MAIN 5.292,0.927 5.521,1.146 0.229,0.219 10 false 1 3.969,1.25 5.042,1.448 1.073,0.198 10 false EFI NO. 1 5.229,1.125 5.76,1.385 0.531,0.26 10 false A43 5.26,2.354 5.792,2.615 0.531,0.26 10 false C1 5.271,2.156 5.5,2.375 0.229,0.219 10 false 53 5.573,1.125 6.646,1.323 1.073,0.198 10 false BATT 5.583,2.354 6.656,2.552 1.073,0.198 10 false E1 5.927,3.229 7,3.427 1.073,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 3 seconds or more.



PROCEDURE

1.INSPECT BATTERY
a.

Check that the battery is not depleted.

Click herePower Source / Network>2GR-FKS BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

2.CHECK BATTERY TERMINAL

NG

CHARGE OR REPLACE BATTERY

2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

NG

REPAIR OR REPLACE BATTERY TERMINAL

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.
A255690C80
0.323,1.063 0.75,1.323 0.427,0.26 1.458,1.125 1.885,1.906 false 0.177,0.156 1.094,0.729 0.917,0.573 10 false *a 1.708,1.927 2.375,2.146 0.667,0.219 10 false BATT 0.427,1.104 0.823,1.406 0.396,0.302 10 false A43
*a Front view of wire harness connector
(to ECM)


Disconnect the A43 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-1 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > Transmission > Clear DTCs
50002 373

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Wait 5 seconds or more.


i.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

j.

Read the DTCs.

Result:
Result Proceed to
DTC P056014 is output A
DTCs are not output B




A

5.REPLACE ECM

B

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT