While the engine is being cranked, battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores this DTC.
This monitor runs when the vehicle is driven at 20 km/h (12 mph) or more for 20 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P061512 | Starter Relay Circuit Short to Battery | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
All of the following conditions are met: (a)
Battery voltage of 10.5 V or more applied to the ECM (b)
Vehicle speed is 20 km/h (12 mph) or more (c)
Engine speed is more than 1000 rpm 2.
The starter signal is ON 3.
20 seconds or more 4.
1-trip detection logic |
·
Park/neutral position switch assembly ·
Starter relay circuit ·
Cranking holding function circuit ·
Harness and connector ·
ECM ·
Certification ECU (Smart key ECU assembly) |
Comes on | DTC stored | SAE Code:
P0617 |
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following procedure.
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Drive the vehicle for 20 seconds or more under the following conditions:
Engine speed is 1000 rpm or more.
Vehicle speed is 20 km/h (12 mph) or more.
Check for DTCs again.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / Starter SW.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter SW | Starter signal | OFF or ON | ·
ON: Starter operating ·
OFF: Starter not operating |
- |
| Tester Display |
|---|
| Starter SW |
Read the Data List according to the display on the GTS.
| Condition | Starter SW |
|---|---|
| Ignition switch ON | OFF |
Read the Data List according to the display on the GTS while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12 mph) or more.
| Condition | Starter SW |
|---|---|
| Driving at 20 km/h (12 mph) or more (engine speed 1000 rpm or more) | OFF |
If the result of either of the above is not as specified, proceed to the next step with the ignition switch ON, the GTS connected and Data List item "Starter SW" selected.
| Proceed to |
|---|
| OK |
| NG |
If the starter assembly operates continuously when the ignition switch is turned ON, proceed to the next step without reading the Data List item "Starter SW".
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Enter the following menus: Powertrain / Transmission / Data List / Starter SW.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter SW | Starter signal | OFF or ON | ·
ON: Starter operating ·
OFF: Starter not operating |
- |
| Tester Display |
|---|
| Starter SW |
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Read the Data List according to the display on the GTS.
| Result | Proceed to |
|---|---|
| The Data List item "Starter SW" does not change from ON. | A |
| The Data List item "Starter SW" changes from ON to OFF. | B |
When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST relay is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
The purpose of this step is to check for ST relay terminal voltage under abnormal conditions.
| *1 | No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly |
| *2 | ST Relay Holder |
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Turn the ignition switch to ON.
Measure the voltage between ST relay terminal 2 and body ground.
Make a note of the measured voltage as it will be necessary for inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST relay.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:
Short to +B in the circuit of a connected ECU or park/neutral position switch assembly.
Short to +B in the wire harness.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly |
| *2 | ST Relay Holder |
Disconnect the C14 park/neutral position switch assembly connector.
Measure the voltage between ST relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected. | A |
| The voltage between ST relay terminal 2 and body ground changes when the connector is disconnected. | B |
If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>COMPONENTS
| *1 | No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly |
| *2 | ST Relay Holder |
Disconnect the A43 ECM connector.
Measure the voltage between ST relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected (w/o Smart Entry and Start System). | A |
| The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected (w/ Smart Entry and Start System). | B |
| The voltage between ST relay terminal 2 and body ground changes when the connector is disconnected. | C |
If the voltage is the same before and after disconnecting the connector, the ECM is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
C
Disconnect the A43 ECM connector.
Disconnect the C14 park/neutral position switch assembly connector.
Disconnect the F10 certification ECU (smart key ECU assembly) connector.
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A43-43 (STA), C14-9 (L), F10-12 (STA) or 2 (ST relay) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION