Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _060164 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0298261 AUTOMATIC TRANSAXLE SYSTEM C

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P070513  Transmission Range Sensor "A" Circuit Open  P070562  Transmission Range Sensor "A" Signal Compare Failure  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070513 Transmission Range Sensor "A" Circuit Open 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The ignition switch is ON and battery voltage is 10.5 V or more.

2.

All of the following signals are OFF simultaneously:

-

NSW input signal

-

P input signal

-

R input signal

-

N input signal

-

D input signal


3.

60 seconds

4.

2-trip detection logic


·

Park/neutral position switch assembly

·

Open in park/neutral position switch assembly circuit

·

ECM


Comes on DTC stored SAE Code:
P0705
P070562 Transmission Range Sensor "A" Signal Compare Failure 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The ignition switch is ON and battery voltage is 10.5 V or more.

2.

Any 2 or more of the following signals are ON simultaneously:

-

(NSW, P or N) input signal

-

R input signal

-

D input signal


3.

2 seconds

4.

2-trip detection logic


·

Park/neutral position switch assembly

·

Short in park/neutral position switch assembly circuit

·

ECM


Comes on DTC stored SAE Code:
P0705

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, R, D or S).

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously and will then illuminate the MIL and store a DTC.

WIRING DIAGRAM

C368292E01
2.604,3.813 3.063,4.01 0.458,0.198 10 false C14 5.719,4.073 6.177,4.271 0.458,0.198 10 false C1 4.969,3.26 5.427,3.458 0.458,0.198 10 false 139 4.958,2.656 5.417,2.854 0.458,0.198 10 false 140 4.948,2.063 5.406,2.26 0.458,0.198 10 false 107 4.948,1.458 5.406,1.656 0.458,0.198 10 false 108 4.958,0.854 5.417,1.052 0.458,0.198 10 false 106 5.323,0.854 5.781,1.052 0.458,0.198 10 false NSW 5.333,1.458 5.792,1.656 0.458,0.198 10 false P 5.333,2.073 5.792,2.271 0.458,0.198 10 false R 5.323,2.667 5.781,2.865 0.458,0.198 10 false N 5.333,3.26 5.792,3.458 0.458,0.198 10 false D 3.792,3.26 4.25,3.458 0.458,0.198 10 false 7 3.792,2.656 4.25,2.854 0.458,0.198 10 false 8 3.792,2.063 4.25,2.26 0.458,0.198 10 false 2 3.792,1.458 4.25,1.656 0.458,0.198 10 false 3 3.781,0.854 4.24,1.052 0.458,0.198 10 false 4 3.542,0.854 4,1.052 0.458,0.198 10 false B 3.479,1.458 3.938,1.656 0.458,0.198 10 false PL 3.479,2.063 3.938,2.26 0.458,0.198 10 false RL 3.479,2.656 3.938,2.854 0.458,0.198 10 false NL 3.469,3.26 3.927,3.458 0.458,0.198 10 false DL 2.781,2.375 3.24,2.573 0.458,0.198 10 false RB 2.781,0.854 3.24,1.052 0.458,0.198 10 false L 5.99,0.688 6.448,0.885 0.458,0.198 10 false 12 V 5.719,4.25 6.177,4.448 0.458,0.198 10 false ECM 2.563,2.375 3.021,2.573 0.458,0.198 10 false 1 2.542,0.854 3,1.052 0.458,0.198 10 false 9 2.604,3.979 3.948,4.344 1.344,0.365 10 false Park/Neutral Position Switch Assembly 0.885,0.969 2.573,1.167 1.688,0.198 10 false to ST Relay 0.354,1.688 2.042,1.885 1.688,0.198 10 false from ECU-ACC Fuse 0.375,2.479 2.063,2.677 1.688,0.198 10 false from BKUP LP Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Check the battery voltage is 10.5 V or more.

2.

Turn the ignition switch to ON.

3.

Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more each.

4.

Turn the ignition switch off.

5.

Perform steps (1) through (3) again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the C14 park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C14-1 (RB) - Body ground Ignition switch ON 11 to 14 V
C14-1 (RB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)
a.

Disconnect the C14 park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C14-4 (B) - Body ground Ignition switch ON 11 to 14 V
C14-4 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712C83
1.823,0.958 2.135,0.385 true 1.594,0.958 1.75,0.354 true 1.271,0.948 0.833,0.375 true 1.313,1.792 1.49,1.292 true 2,1.781 1.719,1.292 true 0.865,1.781 1.344,1.281 true 1.385,0.938 1.198,0.344 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.708,0.292 0.865,0.49 0.156,0.198 10 false B 1.813,0.292 2.063,0.49 0.25,0.198 10 false RL 2.198,0.302 2.448,0.5 0.25,0.198 10 false RB 0.771,1.74 1.021,1.938 0.25,0.198 10 false L 2.063,1.74 2.313,1.938 0.25,0.198 10 false DL 1.146,1.75 1.396,1.948 0.25,0.198 10 false NL 1,0.271 1.417,0.469 0.417,0.198 10 false PL
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the C14 park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
1 (RB) - 7 (DL) Shift lever in D, S, "+" or "-" Below 1 Ω
4 (B) - 9 (L) Shift lever not in P or N 10 kΩ or higher
1 (RB) - 3 (PL) Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever not in D, S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Connect the C14 park/neutral position switch assembly connector.


b.

Disconnect the C1 ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C1-108 (P) - Body ground
·

Ignition switch ON

·

Shift lever in P


11 to 14 V
C1-107 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
C1-140 (N) - Body ground
·

Ignition switch ON

·

Shift lever in N


11 to 14 V
C1-139 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D, S, "+" or "-"


11 to 14 V
C1-108 (P) - Body ground
·

Ignition switch ON

·

Shift lever not in P


Below 1 V
C1-107 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
C1-140 (N) - Body ground
·

Ignition switch ON

·

Shift lever not in N


Below 1 V
C1-139 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D, S, "+" or "-"


Below 1 V


HINT:

*: The voltage will drop slightly due to the illumination of the back up lights.



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the C14 park/neutral position switch assembly connector.


b.

Disconnect the C1 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C14-4 (B) - C1-106 (NSW) Always Below 1 Ω
C14-4 (B) or C1-106 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT