The ATF temperature sensor converts the automatic transaxle fluid (ATF) temperature into a resistance value for use by the ECM.
The ECM applies voltage to the temperature sensor through terminal THO1 of the ECM.
The sensor resistance changes with the ATF temperature. As the temperature rises, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance and voltage decrease as the temperature rises.
The ECM calculates the ATF temperature based on the voltage signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P071011 | Transmission Fluid Temperature Sensor "A" Circuit Short To Ground | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The battery voltage is 8 V or more, the ignition switch is ON and the starter is off. 2.
ATF temperature sensor voltage is less than 0.142 V 3.
0.5 seconds 4.
1-trip detection logic |
·
Short to ground in ATF temperature sensor circuit ·
Transmission wire (ATF temperature sensor) ·
ECM |
Comes on | DTC stored | SAE Code:
P0712 |
This DTC indicates a short to ground in the ATF temperature sensor circuit. The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and can detect a short to ground in the ATF temperature sensor circuit. If the resistance value of the ATF temperature sensor is below 79 Ω*, the ECM interprets this as a malfunction of the ATF temperature sensor or in the wire harness, illuminates the MIL and stores this DTC.
*: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.
The ATF temperature can be checked in the Data List.
Refer to DTC P071000.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>P071000
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the ignition switch to ON and wait for 3 seconds or more.
Check for DTCs again.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR
DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / A/T Oil Temperature No.1.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Temperature No.1 | ATF temperature sensor value | Min.: -40°C (-40°F)
Max.: 150°C (302°F) |
·
Approximately 80°C (176°F): After stall speed test ·
Equal to ambient temperature: When engine is cold |
If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted |
| Tester Display |
|---|
| A/T Oil Temperature No.1 |
If DTC P071011 is output and the GTS indicates 150°C (302°F) or higher, there is a short in the circuit.
If DTC P071015 is output and the GTS indicates -40°C (-40°F), the circuit is open.
Check the temperature displayed on the GTS in order to check if a malfunction exists.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 150°C (302°F) or higher | Short circuit |
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / A/T Oil Temperature No.1.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Temperature No.1 | ATF temperature sensor value | Min.: -40°C (-40°F)
Max.: 150°C (302°F) |
·
Approximately 80°C (176°F): After stall speed test ·
Equal to ambient temperature: When engine is cold |
If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted |
| Tester Display |
|---|
| A/T Oil Temperature No.1 |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
Disconnect the C1 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-86 (THO1) - C1-133 (ETHW) | Always | 79 Ω to 156 kΩ |
| C1-133 (ETHW) - Body ground | Always | 10 kΩ or higher |
| C1-86 (THO1) - Body ground | Always | 10 kΩ or higher |
If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.
| ATF Temperature | Specified Condition |
|---|---|
| 10°C (50°F) | 5 to 8 kΩ |
| 25°C (77°F) | 2.5 to 4.5 kΩ |
| 110°C (230°F) | 0.22 to 0.28 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION
Disconnect the C62 transmission wire connector.
Disconnect the C1 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C62-1 (OT+) or C1-86 (THO1) - Body ground | Always | 10 kΩ or higher |
| C62-2 (OT-) or C1-133 (ETHW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
When Not Using the Engine Support Bridge: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE(When Not Using the Engine Support Bridge)>COMPONENTS
When Using the Engine Support Bridge: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE(When Using the Engine Support Bridge)>COMPONENTS
NG