Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0298312 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

DTC C1622 is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the television camera assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Open or Short Circuit in Back Camera Signal Open or short in the television camera signal circuit
·

Harness or connector

·

Television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E238809E21
5.021,2.229 5.51,2.417 0.49,0.188 10 false GND1 1.771,1.823 2.271,2 0.5,0.177 10 false CGND 5.021,1.813 5.542,1.979 0.521,0.167 10 false CGND 5.021,0.646 5.406,0.813 0.385,0.167 10 false CB+ 5.021,1.042 5.458,1.229 0.438,0.188 10 false CV+ 5.021,1.438 5.417,1.625 0.396,0.188 10 false CV- 1.792,0.656 2.198,0.854 0.406,0.198 10 false CB+ 1.781,1.042 2.208,1.219 0.427,0.177 10 false CV+ 1.792,1.448 2.167,1.635 0.375,0.188 10 false CV- 2.25,0.521 2.333,0.698 0.083,0.177 10 false 6 2.25,0.917 2.333,1.094 0.083,0.177 10 false 3 2.25,1.313 2.333,1.49 0.083,0.177 10 false 2 2.25,1.719 2.333,1.896 0.083,0.177 10 false 5 4.573,0.635 5.063,0.802 0.49,0.167 10 false F130 4.573,2.208 5.083,2.375 0.51,0.167 10 false F131 0.844,2.271 1.146,2.448 0.302,0.177 10 false X30 4.656,0.448 4.854,0.625 0.198,0.177 10 false 3 4.656,0.844 4.833,1.021 0.177,0.177 10 false 1 4.656,1.24 4.948,1.427 0.292,0.188 10 false 2 4.656,1.646 4.885,1.823 0.229,0.177 10 false 9 4.698,2.042 4.896,2.219 0.198,0.177 10 false 3 0.844,2.438 2.385,2.792 1.542,0.354 10 false Television Camera Assembly 4.969,2.688 6.323,2.948 1.354,0.26 10 false Parking Assist ECU 3.198,1.615 3.792,2.094 0.594,0.479 10 false * 3.135,3.125 4.719,3.667 1.583,0.542 10 false *: Shielded 4.573,1.021 5.063,1.188 0.49,0.167 10 false F130 4.563,1.417 5.052,1.583 0.49,0.167 10 false F130 4.573,1.802 5.063,1.969 0.49,0.167 10 false F130

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F130 parking assist ECU connector.


b.

Disconnect the X30 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-3 (CB+) - X30-6 (CB+) Always Below 1 Ω
F130-1 (CV+) - X30-3 (CV+) Always Below 1 Ω
F130-2 (CV-) - X30-2 (CV-) Always Below 1 Ω
F130-9 (CGND) - X30-5 (CGND) Always Below 1 Ω
F130-3 (CB+) or X30-6 (CB+) - Body ground Always 10 kΩ or higher
F130-1 (CV+) or X30-3 (CV+) - Body ground Always 10 kΩ or higher
F130-2 (CV-) or X30-2 (CV-) - Body ground Always 10 kΩ or higher
F130-9 (CGND) or X30-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CV-, CGND)
a.

Disconnect the F130 parking assist ECU connector.


b.
E181084C22
2.458,1.75 2.75,2.625 true 2.323,2.021 2.073,2.688 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.906,2.719 2.323,2.885 0.417,0.167 10 false CGND 2.698,2.667 3.031,2.833 0.333,0.167 10 false CV-
*a Component without harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (CV-) - Body ground Always Below 1 Ω
9 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

3.CHECK PARKING ASSIST ECU (CB+, CGND)
a.
E272332C79
1.49,0.188 1.906,0.427 0.417,0.24 2.688,1.927 2.479,1.927 2.479,1.927 2.344,1.24 true 2.333,1.052 2.521,0.333 2.521,0.333 2.708,0.333 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 2.771,0.24 3.115,0.427 0.344,0.188 10 false CB+ 2.74,1.833 3.167,2.021 0.427,0.188 10 false CGND 1.542,0.208 2,0.406 0.458,0.198 10 false F130
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-9 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-3 (CB+) - F130-9 (CGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.CHECK TELEVISION CAMERA ASSEMBLY (CV+, CGND)

NG

4.CHECK TELEVISION CAMERA ASSEMBLY (CV+, CGND)
a.

Remove the parking assist ECU with the connector still connected.


b.

Using an oscilloscope, check the waveform of the television camera assembly.

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E272333C72
1.344,0.365 1.75,0.583 0.406,0.219 2.479,0.604 2.344,0.604 2.344,0.604 2.25,1.302 true 2.021,1.51 2.115,2.365 2.115,2.365 2.281,2.365 true 3.458,1.823 3.583,2.417 3.583,2.417 3.667,2.417 false 3.563,1.802 4.167,2.417 4.167,2.417 4.333,2.417 false 5.667,1.698 5.5,2.417 5.5,2.417 5.333,2.417 false 5.792,1.646 6,2.417 6,2.417 6.167,2.417 false 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.396,0.375 1.854,0.573 0.458,0.198 10 false F130 2.323,2.271 2.781,2.469 0.458,0.198 10 false CGND 2.542,0.521 3,0.719 0.458,0.198 10 false CV+ 2.729,1.302 3.188,1.5 0.458,0.198 10 false GND 4.865,1.302 5.323,1.5 0.458,0.198 10 false GND 3.021,0.406 3.333,0.604 0.313,0.198 10 false *b 5.125,0.406 5.438,0.604 0.313,0.198 10 false *c 3.719,2.354 4.031,2.552 0.313,0.198 10 false *d 5.167,2.344 5.479,2.542 0.313,0.198 10 false *d 4.396,2.344 4.708,2.542 0.313,0.198 10 false *e 6.208,2.333 6.521,2.531 0.313,0.198 10 false *e
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.



Measurement Condition
Item Content
Terminal No. (Symbol) F130-1 (CV+) - F130-9 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor switch on

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG