Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0298312 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the parking assist ECU receives a signal via CAN communication from the steering sensor that indicates a power supply system problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering sensor +B
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E224380E88
1.125,3.219 2.875,3.396 1.75,0.177 10 false : CAN Communication Line 3.229,0.604 3.583,0.781 0.354,0.177 10 false BAT 3.229,1.708 3.563,1.885 0.333,0.177 10 false ESS 5.375,2.198 6.646,2.427 1.271,0.229 10 false Parking Assist ECU 2.167,1.344 3.177,1.521 1.01,0.177 10 false IG1 NO. 3 2.115,0.802 3.198,1 1.083,0.198 10 false MPX-B NO. 1 0.375,1.167 1.75,1.396 1.375,0.229 10 false from IG1-MAIN Relay 0.927,0.615 2.563,0.792 1.635,0.177 10 false from Battery 3.167,2.375 4.729,2.771 1.563,0.396 10 false Steering Sensor 3.031,0.51 3.156,0.688 0.125,0.177 10 false 5 3.031,1.052 3.156,1.229 0.125,0.177 10 false 4 3.031,1.604 3.25,1.792 0.219,0.188 10 false 1 3.229,1.156 3.531,1.333 0.302,0.177 10 false IG1 3.167,2.198 3.51,2.375 0.344,0.177 10 false F58

CAUTION / NOTICE / HINT

NOTICE:
·

Since the panoramic view monitor system has functions that use the CAN communication system, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)
a.

Disconnect the F58 steering sensor connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F58-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F58-4 (IG1) - F58-1 (ESS) Ignition switch ON 11 to 14 V
F58-5 (BAT) - F58-1 (ESS) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR