Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0298312 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the parking assist ECU. The parking assist ECU controls the panoramic view monitor system.

WIRING DIAGRAM

E301406E21
5.073,2.948 6.417,3.188 1.344,0.24 10 false Parking Assist ECU 5.083,2.781 5.542,2.979 0.458,0.198 10 false F131 5.302,2.135 5.979,2.354 0.677,0.219 10 false GND1 5.313,1.729 5.99,1.948 0.677,0.219 10 false ACC 5.323,1.313 6,1.531 0.677,0.219 10 false IG 5.313,0.885 5.99,1.104 0.677,0.219 10 false +B 5.104,0.781 5.26,0.979 0.156,0.198 10 false 2 5.115,1.188 5.271,1.385 0.156,0.198 10 false 6 5.104,1.625 5.26,1.823 0.156,0.198 10 false 1 5.115,2.021 5.271,2.219 0.156,0.198 10 false 3 3.25,1.073 4.781,1.271 1.531,0.198 10 false MPX-B NO. 3 3.302,1.49 4.833,1.688 1.531,0.198 10 false IG1 NO. 3 3.323,1.917 4.115,2.135 0.792,0.219 10 false ECU-ACC 1.396,0.875 4,1.073 2.604,0.198 10 false from Battery 0.844,1.292 3.448,1.49 2.604,0.198 10 false from IG1-NO. 3 Relay 1.177,1.708 3.781,1.906 2.604,0.198 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


HINT:
·

The parking assist ECU is connected to other ECUs via CAN communication or AVC-LAN communication.

·

If the parking assist ECU does not operate due to a power source problem, the navigation system DTC may be stored due to an AVC-LAN communication interruption.

·

If the parking assist ECU does not operate due to a power source problem, other system DTCs may be stored due to a CAN communication interruption.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BODY GROUND)
a.

Disconnect the F131 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-3 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)
a.

Disconnect the F131 parking assist ECU connector.


b.
C280345C26
1.438,0.281 1.854,0.531 0.417,0.25 0.49,1.188 0.615,1.188 0.615,1.188 1.01,1.26 true 2.781,0.479 2.521,0.479 2.521,0.479 2.208,1.083 true 0.552,0.698 0.677,0.698 0.677,0.698 1.188,1.083 true 0.479,0.906 0.604,0.906 0.604,0.906 0.958,1.094 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.5,0.313 1.917,0.51 0.417,0.198 10 false F131 0.302,0.615 0.802,0.781 0.5,0.167 10 false +B 2.823,0.396 3.323,0.563 0.5,0.167 10 false GND1 0.292,1.094 0.792,1.26 0.5,0.167 10 false IG 0.146,0.813 0.646,0.979 0.5,0.167 10 false ACC
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F131-2 (+B) - F131-3 (GND1) Always 11 to 14 V
F131-1 (ACC) - F131-3 (GND1) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
F131-6 (IG) - F131-3 (GND1) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR