Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0298312 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1682  Front Camera Current Malfunction  


DESCRIPTION

DTC C1682 is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the front television camera assembly connected to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1682 Front Camera Current Malfunction Open or short in the front television camera signal circuit
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E238808E13
5.25,1.667 6.74,2.052 1.49,0.385 10 false Parking Assist ECU 1.01,1.74 2.885,2.073 1.875,0.333 10 false Front Television Camera Assembly 2.24,1.01 2.333,1.188 0.094,0.177 10 false 5 1.74,0.719 2.146,0.906 0.406,0.188 10 false BCB+ 1.719,1.125 2.177,1.302 0.458,0.177 10 false BGND 1.031,1.51 1.333,1.688 0.302,0.177 10 false A90 5.26,1.51 5.781,1.688 0.521,0.177 10 false F130 5.406,0.708 5.917,0.917 0.51,0.208 10 false BCB+ 5.406,1.115 5.927,1.313 0.521,0.198 10 false BGND 2.24,0.604 2.365,0.792 0.125,0.188 10 false 6 5.146,1.021 5.406,1.198 0.26,0.177 10 false 27 5.146,0.615 5.396,0.792 0.25,0.177 10 false 15 3.479,2.365 5.354,2.698 1.875,0.333 10 false *: Shielded 3.531,0.969 5.406,1.302 1.875,0.333 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F130 parking assist ECU connector.


b.

Disconnect the A90 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-15 (BCB+) - A90-6 (BCB+) Always Below 1 Ω
F130-27 (BGND) - A90-5 (BGND) Always Below 1 Ω
F130-15 (BCB+) or A90-6 (BCB+) - Body ground Always 10 kΩ or higher
F130-27 (BGND) or A90-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
E272332C81
1.542,0.167 1.885,0.375 0.344,0.208 0.927,0.354 1.094,0.354 1.094,0.354 1.323,1.198 true 0.938,1.938 1.104,1.938 1.104,1.938 1.333,1.375 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.563,0.188 2.021,0.385 0.458,0.198 10 false F130 0.521,0.26 1.135,0.458 0.615,0.198 10 false BCB+ 0.51,1.844 1.125,2.042 0.615,0.198 10 false BGND
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-27 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-15 (BCB+) - F130-27 (BGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

NG