Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0298312 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

DTC C1621 is stored if the parking assist ECU determines that the input/output signal communication with the television camera assembly is abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1621 Back Camera Power Supply Failure Television camera assembly power supply malfunction
·

Harness or connector

·

Television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E238808E12
5.25,1.667 6.74,2.052 1.49,0.385 10 false Parking Assist ECU 1.021,1.688 2.896,2.021 1.875,0.333 10 false Television Camera Assembly 2.24,1.01 2.333,1.188 0.094,0.177 10 false 5 1.885,0.729 2.292,0.917 0.406,0.188 10 false CB+ 1.781,1.125 2.24,1.302 0.458,0.177 10 false CGND 1.031,1.51 1.333,1.688 0.302,0.177 10 false X30 5.26,1.51 5.781,1.688 0.521,0.177 10 false F130 5.406,0.708 5.708,0.885 0.302,0.177 10 false CB+ 5.406,1.115 5.927,1.313 0.521,0.198 10 false CGND 2.24,0.604 2.365,0.792 0.125,0.188 10 false 6 5.146,1.021 5.406,1.198 0.26,0.177 10 false 9 5.146,0.615 5.396,0.792 0.25,0.177 10 false 3 3.417,2.208 4.469,2.396 1.052,0.188 10 false *: Shielded 3.656,0.99 3.958,1.167 0.302,0.177 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F130 parking assist ECU connector.


b.

Disconnect the X30 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-3 (CB+) - X30-6 (CB+) Always Below 1 Ω
F130-9 (CGND) - X30-5 (CGND) Always Below 1 Ω
F130-3 (CB+) or X30-6 (CB+) - Body ground Always 10 kΩ or higher
F130-9 (CGND) or X30-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CB+, CGND)
a.
E272332C78
1.49,0.188 1.906,0.427 0.417,0.24 2.688,1.927 2.479,1.927 2.479,1.927 2.344,1.24 true 2.333,1.052 2.521,0.333 2.521,0.333 2.708,0.333 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 2.771,0.24 3.115,0.427 0.344,0.188 10 false CB+ 2.74,1.833 3.167,2.021 0.427,0.188 10 false CGND 1.552,0.208 2.01,0.406 0.458,0.198 10 false F130
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-9 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-3 (CB+) - F130-9 (CGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

NG