Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0298312 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1681  Front Camera Feedback Malfunction  


DESCRIPTION

DTC C1681 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1681 Front Camera Feedback Malfunction Front television camera power supply failure
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E238809E22
5.021,2.229 5.51,2.417 0.49,0.188 10 false GND1 1.719,1.823 2.219,2 0.5,0.177 10 false BGND 5.021,1.823 5.542,1.99 0.521,0.167 10 false BGND 5.021,0.646 5.552,0.823 0.531,0.177 10 false BCB+ 5.021,1.042 5.51,1.24 0.49,0.198 10 false BCV+ 5.021,1.438 5.417,1.625 0.396,0.188 10 false BCV- 1.729,0.656 2.135,0.854 0.406,0.198 10 false BCB+ 1.719,1.042 2.146,1.219 0.427,0.177 10 false BCV+ 1.75,1.448 2.125,1.635 0.375,0.188 10 false BCV- 2.25,0.521 2.333,0.698 0.083,0.177 10 false 6 2.25,0.917 2.333,1.094 0.083,0.177 10 false 3 2.25,1.313 2.333,1.49 0.083,0.177 10 false 2 2.25,1.719 2.333,1.896 0.083,0.177 10 false 5 4.563,0.625 5.052,0.792 0.49,0.167 10 false F130 4.563,2.208 5.073,2.375 0.51,0.167 10 false F131 0.844,2.271 1.146,2.448 0.302,0.177 10 false A90 4.656,0.448 4.854,0.625 0.198,0.177 10 false 15 4.656,0.854 4.833,1.031 0.177,0.177 10 false 13 4.656,1.25 4.948,1.438 0.292,0.188 10 false 14 4.656,1.646 4.885,1.823 0.229,0.177 10 false 27 4.698,2.042 4.896,2.219 0.198,0.177 10 false 3 0.844,2.438 2.385,2.792 1.542,0.354 10 false Front Television Camera Assembly 4.969,2.688 6.323,2.948 1.354,0.26 10 false Parking Assist ECU 3.198,1.615 3.792,2.094 0.594,0.479 10 false * 3.135,3.125 4.719,3.667 1.583,0.542 10 false *: Shielded 4.563,1.031 5.052,1.198 0.49,0.167 10 false F130 4.573,1.417 5.063,1.583 0.49,0.167 10 false F130 4.563,1.813 5.052,1.979 0.49,0.167 10 false F130

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F130 parking assist ECU connector.


b.

Disconnect the A90 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-15 (BCB+) - A90-6 (BCB+) Always Below 1 Ω
F130-13 (BCV+) - A90-3 (BCV+) Always Below 1 Ω
F130-14 (BCV-) - A90-2 (BCV-) Always Below 1 Ω
F130-27 (BGND) - A90-5 (BGND) Always Below 1 Ω
F130-15 (BCB+) or A90-6 (BCB+) - Body ground Always 10 kΩ or higher
F130-13 (BCV+) or A90-3 (BCV+) - Body ground Always 10 kΩ or higher
F130-14 (BCV-) or A90-2 (BCV-) - Body ground Always 10 kΩ or higher
F130-27 (BGND) or A90-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (BCV-, BGND)
a.

Disconnect the F130 parking assist ECU connector.


b.
E181084C23
1.417,1.99 1.74,2.813 true 1.26,2.135 1.01,2.802 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 0.771,2.865 1.188,3.031 0.417,0.167 10 false BGND 1.625,2.844 2.083,3.01 0.458,0.167 10 false BCV-
*a Component without harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
27 (BGND) - Body ground Always Below 1 Ω
14 (BCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

3.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
E272332C80
1.542,0.167 1.885,0.375 0.344,0.208 0.927,0.354 1.094,0.354 1.094,0.354 1.323,1.198 true 0.938,1.938 1.104,1.938 1.104,1.938 1.333,1.375 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.552,0.177 2.01,0.375 0.458,0.198 10 false F130 0.521,0.26 1.135,0.458 0.615,0.198 10 false BCB+ 0.51,1.844 1.125,2.042 0.615,0.198 10 false BGND
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-27 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-15 (BCB+) - F130-27 (BGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

NG

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)
a.

Remove the parking assist ECU with the connector still connected.


b.

Using an oscilloscope, check the waveform of the front television camera assembly.

HINT:

A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E272333C73
1.313,0.417 1.688,0.667 0.375,0.25 0.917,2.417 1.083,2.417 1.083,2.417 1.177,1.646 true 1.719,2.417 1.552,2.417 1.552,2.417 1.396,1.5 true 2.969,2.594 3.135,2.594 3.135,2.594 3.438,1.823 true 6.083,2.417 5.917,2.417 5.917,2.417 5.792,1.646 true 5.198,2.458 5.365,2.458 5.365,2.458 5.667,1.688 true 3.854,2.573 3.688,2.573 3.688,2.573 3.563,1.802 true 1.354,0.448 1.813,0.646 0.458,0.198 10 false F130 2.75,1.292 3.208,1.49 0.458,0.198 10 false GND 4.885,1.292 5.344,1.49 0.458,0.198 10 false GND 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 2.958,0.313 3.271,0.469 0.313,0.156 10 false *b 5.094,0.302 5.406,0.458 0.313,0.156 10 false *c 2.781,2.5 3.094,2.656 0.313,0.156 10 false *d 6.125,2.344 6.438,2.5 0.313,0.156 10 false *e 3.906,2.5 4.219,2.656 0.313,0.156 10 false *e 5.042,2.385 5.354,2.542 0.313,0.156 10 false *d 0.479,2.333 1.094,2.531 0.615,0.198 10 false BGND 1.781,2.323 2.396,2.521 0.615,0.198 10 false BCV+
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the front television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.



Measurement Condition
Item Content
Terminal No. (Symbol) F130-13 (BCV+) - F130-27 (BGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor switch on

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG