Home › Engine / Hybrid System › 2GR-FKS (COOLING) › COOLING FAN ECU › from 2016.11
RM3160E _51 Engine / Hybrid System _060161 2GR-FKS COOLING _0297919 COOLING FAN ECU G

2GR-FKS COOLING  COOLING FAN ECU  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK COOLING FAN SYSTEM

a.

Check and ensure the following conditions:

i.

The ignition switch is off.


ii.

The engine coolant temperature is less than 95°C (203°F).


iii.

The battery voltage is between 11 to 14 V.


iv.

The A/C switch is off.



b.

Connect the pickup of a clamp-on ammeter around either of the 2 wires for the cooling fan motor.


c.

Turn the ignition switch to ON and wait for approximately 10 seconds. Check that the cooling fans are not operating.


d.

Start the engine. Check that the cooling fans are not operating with the engine idling.

HINT:
·

Make sure that the engine coolant temperature is less than 95°C (203°F).

·

Turn the A/C switch off.




e.

Check that the cooling fans operate when the A/C switch is turned on.

HINT:
·

Adjust the air conditioning control to the maximum setting.

·

Adjust the blower speed to the high setting.




f.

Measure the current while the cooling fan motors are operating.

Standard Current:
Item Condition Specified Condition
Cooling fan motor LH Battery voltage applied at 20°C (68°F) 11.5 to 17.5 A
Cooling fan motor RH 11.5 to 17.5 A


HINT:

Make sure that the engine coolant temperature is less than 95°C (203°F).



g.

Check that the cooling fans operate when the engine coolant temperature sensor connector is disconnected.


h.

Measure the current while the cooling fan motors are operating.

Standard Current:
Item Condition Specified Condition
Cooling fan motor LH Battery voltage applied at 20°C (68°F) 11.5 to 17.5 A
Cooling fan motor RH 11.5 to 17.5 A



i.
A320309C01
0.052,0.042 0.448,0.271 0.396,0.229 10 false *a 0.375,1.146 0.688,1.302 0.313,0.156 10 false *b 0.385,1.667 0.698,1.823 0.313,0.156 10 false *c 0.365,2.542 0.677,2.698 0.313,0.156 10 false *d 0.375,3.094 0.688,3.25 0.313,0.156 10 false *e 0.052,2.135 0.365,2.292 0.313,0.156 10 false *f 1.229,3.677 1.542,3.875 0.313,0.198 10 false 95 1.646,3.677 1.958,3.875 0.313,0.198 10 false 97 2.208,3.667 2.521,3.865 0.313,0.198 10 false 100 2.625,3.656 2.938,3.854 0.313,0.198 10 false 102 1.188,3.917 1.646,4.115 0.458,0.198 10 false 203 1.604,3.917 2.063,4.115 0.458,0.198 10 false 207 2.219,3.917 2.677,4.115 0.458,0.198 10 false 212 2.635,3.917 3.094,4.115 0.458,0.198 10 false 216 2.99,3.927 3.281,4.208 0.292,0.281 10 false (°F) 2.99,3.656 3.281,3.938 0.292,0.281 10 false (°C)
*a Operating Diagram
*b MAX HI
*c HI
*d LO
*e OFF
*f Fan Speed


After the engine is warmed up, check that the cooling fans operate as shown in the illustration.

HINT:
·

The engine coolant temperature at which the cooling fans start operating is approximately 97°C (207°F).

·

This system can also be checked using the GTS.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature



Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205